Analog

Showing results for: analogue
Refine Analog companies and products:
analog analogue analog circuit analog ic analogue circuit analogue ic analog to digital digital to analog a/d d/a adc dac continuous signal
Click on any vendor
to see a listing of
analogue related products.
  • Nuvoton Technology  (1)
    • WAU8812
      Mono audio Codec for VoIP-telephone, hands-free telephony markets; provides flexibility in performance and power consumption (+)

      Features:

      38376.jpg
      • Robust, high-fidelity, 24-bit signal architecture
      • 93dB Digital-to-Analog Converter (DAC), Signal to Noise Ratio (SNR), and 91dB Analog-to-Digital Converter (ADC) SNR at audio sampling rates from 8 KHz to 48 KHz
      • Industry-leading 6uA standby current, which greatly reduces power consumption and extends battery life in hand-held applications
  • SingMai Electronics  (1)
    • PT5
      PT5 is a very high quality adaptive 2D/3D comb, multi-standard video decoder with sample rate converter and integrated 3D noise reduction (+)

      Features:

      184216468183889261.jpg
      • PAL-B/D/G/I/M/N, NTSC-M/J decoding, (SECAM soon).
      • Pixel by pixel adaptation between notch, 2D 3 line comb and asymmetric minimum delay 3D field/frame combs.
      • 12 bit input, 12 bit demodulation, 10 bit comb filter, 10 bit I/O.
  • Seica Test Solutions  (1)
    • S40 Pilot LX
      An extra large flying probe system well-suited to testing any type of electrical board on any type of production run from a single board to high volume (+)

      Features:

      • The extended 24" x 24" board area is particularly suited to larger PCB demands such as PC motherboards and multi-board panels. Speed, precision and reliability from new brushless motor-driven roller bearings
      • High performance mechanical adaptors ensure significant levels of rigidity required to sustain the high acceleration and speed of the new probe technology
      • The S40 Pilot LX has a full suite of test capabilities ranging from simple MDA testing of passive components through to complete, powered-up in-circuit and functional analogue tests, static and dynamic digital tests and vectorless testing
  • Cambridge Pixel  (3)
    • HPx-200 radar card
      Cambridge Pixel's HPx-200 is PCI-based primary radar input card, which interfaces to a wide range of primary radar signals and features dual analogue video inputs (+)

      Features:

      • Accommodates analog and digital radar video types, trigger and azimuth (ACP/ARP and parallel data) signals
      • Captures one or two channels of video at up to 50 MHz using high-precision analogue to digital converters at 12 bits resolution
      • Uses an FPGA for pre-processing of radar video prior to PCI bus-client software transfer
    • HPx-200e
      The HPx-200e is Cambridge Pixel's new PCI Express Radar Interface Card for primary radar acquisition. The card supports the capture of 1 or 2 analogue radar videos with trigger and azimuth data. A board support library is available for Windows or Linux, or Cambridge Pixel's SPx software suite provides processing, scan conversion and target trackign capabilities. (+)

      Features:

      193291468811362524.jpg
      • Radar video capture
      • Flexible interfacing
      • PCI Express Interface Bus
    • HPx-100
      A flexible, PCI-based primary radar interface card for analog and digital radars (+)

      Features:

      • Card is supported by Windows and Linux
      • Analog and digital interface with trigger and azimuth turning data
      • Onboard high-performance FPGA for radar processing
  • ACCES I/O Products, Inc.  (6)
    • 104-AIO16-16
      Multifunctional high-speed analog-to-digital and digital-to-analog converter card for PC/104 (+)

      Features:

      14717.jpg
      • 16 single-ended/eight differential analog inputs
      • 16-bit resolution, 500 Ksamples/sec conversions
      • Nine input ranges (uni/bipolar)
    • 104-AIM-32
      PC/104 analog signal multiplexer for data acquisition (+)

      Features:

      • Card multiplexes and conditions 16 differential or 32 single-ended analog signals before passing them to an analog-to-digital converter card
      • Removable screw terminal block provided for termination of the input signals coming from thermocouples, three-wire RTDs, strain gauges, four 20mA current inputs as well as DC and AC voltage inputs
      • Factory installed bridge completion circuit, current-to-voltage circuit, and current sourcing circuits for the RTDs are optional
    • DAQ-PACK System
      The DAQ-PACK offers 32, 64, 96 or 128 channels of single-ended or differential analog inputs, a unique real-time internal autocalibration system for high accuracy, and a wide ran (+)

      Features:

      52471.jpg
      • 32, 64, 96 or 128-channels, single-ended or differential analog inputs
      • High-speed USB 2.0 multifunction DAQ with sustained sampling speeds up to 500kHz
      • 12 or 16-bit resolution
    • 104-AIM-32A
      A PC/104 signal-conditioning multiplexer and A/D board (+)

      Features:

      16981.jpg
      • 32 single-ended or 16 differential inputs with flexible gain
      • 12-bit, 8-input, 100-kHz A/D board and cable
      • Software programmable channel by channel input range/gain
    • 104-AIO 12-8
      PC/104 analog I/O board features eight channels, 12-bit resolution on input and four channels, 12-bit resolution on output (+)

      Features:

      • Analog input configuration employs an instrumentation preamplifier per channel (differential inputs), 200V common mode rejection, high input impedance, and optional factory channel-by-channel gain, with preset features, to accommodate low-level inputs from sensors
      • Analog output ranges are field selectable with jumpers
      • Digital I/O lines are pulled up to 5V or pulled down to ground
    • USB-AO Series
      Up to 16 analog outputs with 12 or 16-bit resolution (+)

      Features:

      52225.jpg
      • Unipolar and bipolar output ranges
      • Real-time hardware calibration per channel
      • Update outputs individually or simultaneously
  • WinSystems, Inc.  (6)
    • PCM-MIO Multifunction A/D
      Analog and digital I/O on a PC/104 module (+)

      Features:

      41298.jpg
      • 16-bit Analog-to-Digital (A/D) converter
      • Conversion sped: 100K samples per second
      • Two quad 12-bit Digital-to-Analog (D/A) converters
    • Command-based DAQ module
      Command-based intelligent data acquisition system (+)

      Features:

      • Onboard processor handles all scheduling, mode selection, calibration control, and data buffer management
      • Eight analog input ranges: 0-1.25 V, 0-2.5 V, 0-5 V, 0-10 V, ±1.25 V, ±2.5 V, ±5 V, and ±10 V
      • 16-bit Analog-to-Digital (A/D) converter
    • Multifunction A/D
      Versatile, PC/104-based analog input, analog output, and digital I/O board designed for industrial applications requiring high-accuracy analog I/O yet requiring no external calibration (+)

      Features:

      33633.jpg
      • Supports optically isolated analog and digital I/O modules for use in harsh industrial environments
      • Two separate 16-bit A/D converters: Each supports 8-channels for a total of 16 single-ended, 8 differential channels or various combinations of both
      • Analog input ranges are: 0-5V, 0-10V, ±5V, and ±10V
    • A/D & D/A Module
      A versatile, PC/104-based analog input, analog output, and digital I/O board (+)

      Features:

      • Multifunction analog and digital I/O module
      • 12-bit or 16-bit A/D converter
      • Eight 12-bit D/A converters
    • PCM-A/D12/16
      16-bit successive approximation analog-to-digital converter capable of operation over a -40°C to +85°C temperature range with no missing codes (+)

      Features:

      1345.jpg
      • Up to 16 single-ended or 8 differential input channels can be selected
      • Supports input of 0V to +5V and ±10V
      • The conversion rate is 30 microseconds/channel
    • PCM-D/A12
      "No tweak" 12-bit digital-to-analog converter module incorporates non-adjusting, laser-trimmed devices and eliminates onboard potentiometers (+)

      Features:

      1135.jpg
      • Provides 8 independent channels with voltage ranges of 0V to +5V, 0V to +10V, and ±10V
      • Available without onboard DC/DC converter [...]
  • ADLINK Technology, Inc.  (6)
    • PCI-9527
      The PCI-9527 is a high-performance, 2-CH analog input and 2-CH analog output dynamic signal acquisition board. This board is specifically designed for audio testing, acoustic measurement, and vibration analysis applications. The ADLINK PCI-9527 features two 24-bit simultaneous sampling analog input channels. The 24-bit sigmadelta ADC provides a sampling rate up to 432 KS/s at high resolutions, making it ideal for higher bandwidth dynamic signal measurements. The sampling rate can be adjusted by setting the onboard DDS clock source to an appropriate frequency. All channels are sampled simultaneously and accept an input range from ±40 V to ±0.316 V. The PCI-9527 analog input supports software selectable AC or DC coupling and 4 mA bias current for integrated electronic piezoelectric (IEPE) sensors. The ADLINK PCI-9527 also has two channels of 24-bit resolution, high fidelity analog output. The outputs occur simultaneously at software programmable rates up to 216 KS/s. A software programmable output range of ±0.1 V, ±1 V, and ±10 V is available on the output channels. (+)

      Features:

      183912127701794017.jpg
      • 24-Bit Sigma-Delta ADC and DAC
      • 2-CH simultaneous sampling analog input
      • 2-CH simultaneous updated analog input
    • PCIe-9842
      The ADLINK PCIe-9842 is a 200 MS/s 14-bit 1-CH digitizer designed for applications such as LIDAR testing, optical fiber testing, and radar signal acquisition. The 100 MHz bandwidth analog input with 50 ohm impedance is designed to receive ¡Ó1 V high speed signal. With this simplified front-end design and high stable onboard reference, the PCIe-9842 provides not only high accuracy measurement results but also delivers high dynamic performance. For applications that require data to be acquired and transferred in real-time, the PCIe-9842 utilizes the PCI Express x4 bus as its interface. When signals are converted from analog to digital data, the data will be transferred to host system memory continuously because of the high bandwidth of the PCI Express. For applications that require data to be acquired and transferred in real-time, the PCIe-9842 utilizes the PCI Express x4 bus as its interface. When signals are converted from analog to digital data, the data will be transferred to host system memory continuously because of the high bandwidth of the PCI Express. (+)

      Features:

      183913114701794017.jpg
      • Up to 200 MS/s sampling rate
      • High resolution 14-bit ADC
      • ±1 V Input range with 50 Ω input impedance and DC couple
    • DAQ-2000
      A series of half-size data acquisition control cards that incorporate Adlink's carrier and daughter modular design concept (+)

      Features:

      • The digital and analog functions are separated onto isolated boards, with the analog functions on a daughter board
      • Easily upgraded to CompactPCI/PXI by changing the carrier
      • 100% software compatibility
    • DAQe-2200
      PCI Express data acquisition cards (+)

      Features:

      33379.jpg
      • Family of cards can sample up to 64 analog channels with input voltages ranging up to 10 V
      • 2204 model: 12-bit A/D card with 3 MSps (simultaneous); 2205: 16-bit A/D card with 500 KSps (simultaneous); 2206: 16-bit/250 KSps
      • All boards offer differential mode (making 32 analog channels) to eliminate noise, analog and digital triggering, and a system synchronization bus to “lock together” up to four cards
    • PCM-9112+
      PC/104-Plus multifunction DAS module (+)

      Features:

      12729.jpg
      • 12-bit analog input resolution
      • 16 single-ended or eight differential analog inputs
      • Auto-scanning channel selection
    • PCI-9820
      A high-speed, high-resolution data acquisition card (+)

      Features:

      • Two analog inputs and a system synchronization interface (SSI)
      • 14-bit resolution
      • Maintains single-channel sampling rates of 130 MSps and dual-channel rates of 65 MSps
  • Fujitsu  (1)
  • RF Engines Limited  (1)
    • SpectraChip™ IF
      SpectraChip™ IF is a digital replacement for analogue intermediate frequency (IF) filtering used in current spectrum analysers, and is supplied as an IP core for embedding on low cost FPGA devices. SpectraChip™ IF provides a digital implementation of all the standard features, such as resolution bandwidth filtering, video bandwidth filtering and conversion to log power. (+)

      Features:

      • Replaces analogue IF filtering in spectrum analysers
      • IP core applicable to low cost FPGAs
      • Implements all standard spectrum analyser features
  • Annapolis Micro Systems, Inc.  (1)
    • 2.5 GSps 10-Bit ADC FMC
      The 2.5 GSps 10-Bit ADC FMC provides high fidelity and high speed analog-to-digital conversion along with a rug-ged design. The 2.5 GSps 10-Bit ADC FMC is shipped with a custom heatsink which enables proper cooling of the ADC. An on-board temperature monitor is also supplied which allows for real-time monitoring of the ADC’s internal die temperature. The FMC is mechanically and electrically compliant to FMC standard (ANSI/VITA 57.1). (+)

      Features:

      293453569861406184.jpg
      • 2.5 GHz Max Input Sample Rate
      • 10-Bit A/D conversion with e2v® EV10AS150A or EV10AS150B Analog-to-Digital Converter
      • Analog input configuration option: EV10AS150A – Middle Band; EV10AS150B - Low Band & Middle Band
  • Future Technology Devices International Ltd.  (1)
    • VNCLO-START1 kit.
      Integrates an 8-channel, 10-bit ADC, simplifying connection to sensors, actuators and other analogue devices (+)

      Features:

      52475.jpg
      • Supports 38 general-purpose input/output connections
      • Controller chip at the heart of the board integrates a 16/32-bit (instruction/data) MCU core, 16kB of RAM and 256kB of Flash Memory, along with a range of interfaces (UART, SPI, GPIO, FIFO and PWM) [...]
  • Shenzhen WAYJUN Industrial Automation  (2)
    • 8 Channels Analog Signal To RS485
      8-channel Analogue Signal to rs485/232 Signal Output A-D Converter with Modbus,Data Acquisition Samples: Part No.:WJ28-A4-485 means 8 channels 4-20mA input,ouput is RS485 interface Part No.:WJ28-U1-232 means 8 channels 0-5V input,output is RS232 interface Part No.:WJ28-U2-485 means 8 channels 0-10V input,output is RS485 interface (+)

      Features:

      • Eight analog signal acquisition, isolated converter RS-485/232 output
      • 24-bit AD converter, accuracy>0.05%
      • Signal input / output:3000VDC isolation
    • 4-20ma to RS485 Converter with Modbus
      Featuresï?? â—? Analog signal acquisition,isolated RS-485/232 output â—? 12-bit AD converter,testing accuracy>0.1% â—? Can be remotely reconfigured for modules Analog Current signal to RS485 or RS232 Converter,Slim-line plastic housing with integral 35mm DIN rail mounting , LED indication and terminals,power supply(8-32VDC) [...] (+)

      Features:

      325368931670794760.jpg
  • Hectronic AB  (2)
    • H6045
      PC104 board with AMD LX800 (+)

      Features:

      • AMD LX800 500MHz CPU or LX700 433 MHz, LX600 or LX900 on request
      • VGA graphics: Analogue CRT and the choice between TFT or LVDS
      • Ethernet 10/100 Mbit
    • H6045
      PC/104 board with AMD LX800 (+)

      Features:

      • AMD LX800 500MHz CPU or LX700 433 MHz, LX600 or LX900 on request
      • VGA graphics: Analogue CRT and the choice between TFT or LVDS
      • Ethernet 10/100 Mbit
  • AIM-USA  (1)
    • AXE1553-x
      The card is a member of AIM’s family of PCI Express based XMC-Mezzanine (ANSI/ VITA 42.3) modules targeted for embedded MIL-STD-1553A/B applications. The card is designed to meet or exceed vibration requirements as specified in ANSI/VITA 47 for class V3 in conduction cooled applications and class V2 in air-cooled applications. It is also designed to meet the shock requirements specified in ANSI/VITA 47 for class OS2.  All cards are available as conduction cooled rear I/O cards that meet the VITA46.9 x12d + x8d + x24s rear I/O XMC routing scheme.  For other routing schemes please contact your local sales representative.  All cards have the capability to handle up to 4 dual redundant MIL-STD-1553 channels with eight Open/Ground Avionics Level (+35V) Discrete I/O signals in addition to Trigger-I/O. With the provided onboard flash memory the components boot up autonomously after power up. Therefore the cards are well prepared for MIL-STD-1760D and other embedded applications requiring fast and autonomous boot up to operational mode.  An onboard IRIG-B analogue time encoder/ decoder is included with sinusoidal output and ‘freewheeling’ mode for time tag synchronization. (+)

      Features:

      346053114941847663.jpg
      • Up to 4 Dual Redundant MIL-STD-1553 Channels
      • -40°C to +85°C operating temperature range
      • VITA-47 shock and vibration qualified
  • General Standards Corporation  (15 of 45)
    • cPCI66-16AISS8AO4
      12-channel, 16-bit PMC analog input/output board with eight simultaneously sampled analog inputs, four analog outputs, and input sampling rates to 2.0 MSPS per channel (+)

      Features:

      • Analog inputs: 8 differential analog inputs with dedicated 16-bit ADC per channel; true simultaneous sampling of all Inputs to 2.0 MSPS per channel
      • Analog outputs: 4 single-ended analog outputs with dedicated 16-Bit DAC per channel; Simultaneous output clocking rates to 1.0 MSPS per channel
      • Selectable Input/Output ranges: ±10V, ±5V, ±2.5V
    • PMC66-16AISS8AO4
      12-Channel, 16-Bit PMC Analog Input/Output Board with eight simultaneously sampled analog Inputs, four analog outputs, and Input Sampling Rates to 2.0 Msps per channel (+)

      Features:

      35127.jpg
      • Analog Inputs: 8 Differential Analog Inputs with Dedicated 16-Bit ADC per Channel; True Simultaneous Sampling of all Inputs to 2.0 Msps per channel
      • Analog Outputs: 4 Single-Ended Analog Outputs with Dedicated 16-Bit DAC per Channel; Simultaneous Output Clocking Rates to 1.0 Msps per Channel
      • Selectable Input/Output Ranges: ±10V, ±5V, ±2.5V
    • PMC-ADADIO
      A 12-channel analog I/O PMC mezzanine (+)

      Features:

      • Provides 16-bit analog input, analog output, and digital I/O
      • Eight analog input channels are sampled simultaneously
      • Inputs can be sampled continuously or burst-sampled (up to 200 Ksamples/channel for an agregate rate of 1.6 Msamples/sec)
    • CPCI-ADADIO
      A 12-channel analog I/O board that provides high-resolution 16-bit analog input, analog output, and digital I/O (+)

      Features:

      3520.jpg
      • Eight analog input channels are sampled simultaneously
      • Inputs can be sampled continuously or burst-sampled (up to 200,000 samples/channel for an aggregate rate of 1,600,000 samples/sec)
      • The inputs are converted and stored in a 32,000 sample FIFO buffer
    • CPCI-16DSI-VHS
      A versatile multifunction analog I/O board (+)

      Features:

      • The board has 8 analog inputs and 8 analog outputs per board and supports arbitrary waveform generation
      • A single 16-bit scanning Analog-to-Digital converter scans 8 single-ended or 4 differential inputs at an aggregate rate of 72,500 samples per second into the 32,000 sample storage FIFO
      • Up to 250,000 samples per second aggregate output update rates for the 8 D/A channels. Analog outputs are double-buffered and allow for software or hardware (synchronized) strobes for output updating
    • PC104P-16AIO88
      Versatile multifunction analog I/O board for PC/104-Plus (+)

      Features:

      • Eight analog inputs
      • Eight analog outputs per board
      • Supports arbitrary waveform generation
    • PC104P-VIDEO-AI2
      PC-104-Plus analog video input (+)

      Features:

      • Two video digitizers, FIFOs, and a DMA engine
      • Each video digitizer provides luminance and chrominance signal processing for NTSC M, NTSC N, NTSC 4.43, NTSC-Japan, PAL BGHI, PAL N, PAL M, and SECAM
      • Once the interface has been initialized, it transfers frame-after-frame of video input to host memory without host intervention
    • CPCI-12AISS8AO4
      12-channel, 12-bit CompactPCI Analog Input/Output board with eight 2.0 MSPS per Channel Analog Inputs, simultaneous input sampling, wide-range analog inputs; ±100 mV to ±10 V Full-scale (+)

      Features:

      • 8 Differential Analog Inputs with Dedicated 12-Bit, 2.0 MSPS ADC per Channel
      • True Simultaneous Sampling of all Inputs; Minimum data skew
      • Sampling rates to 2.0 MSPS per Channel (16 MSPS Aggregate Rate)
    • PMC-16AIO88
      A multifunction analog I/O PMC board (+)

      Features:

      • Board has eight analog inputs and eight analog outputs and supports arbitrary waveform generation
      • A single 16-bit scanning ADC scans eight single-ended or four differential inputs at an aggregate rate of 72,500 samples/sec into the 32,000-sample storage FIFO
      • Up to 250,000 samples/sec aggregate output update rates for the eight D/A channels
    • cPCI6U-24DSI32R
      32-channel 24-bit Delta-Sigma CompactPCI 6U Analog Input Board with Rear I/O (+)

      Features:

      • Low noise, 24-bit resolution, low phase distortion and multi-board synchronization make the cPCI6U-24DSI32 board ideal for state-of-the-art sonar and noise monitoring applications
      • 32-channel cPCI6U-24DSI32 analog input board provides a high-density 24-bit analog input resources on a standard 6U cPCI expansion board
      • Optimized for flexibility and performance, the board is ideal for a wide variety of applications, ranging from simple precision voltage measurements, to the analysis of complex audio signals and waveforms
    • cPCI66-14HSAI4
      14-bit, 4-channel, 50 MSPS/Channel PMC analog input board (+)

      Features:

      34788.jpg
      • Four-channel, 14-bit wideband analog input board
      • Sampling rates to 50 MSPS per channel
      • Four wideband analog inputs with a dedicated 14-bit ADC per channel
    • cPCI-16AIO88
      Eight analog output channels with a 16-bit D/A converter per channel (+)

      Features:

      • 16-bit scanning ADC for 8 single-ended or 4 differential analog input channels
      • Input and output ranges available as ±10V, ±5V, or ±2.5V
      • Input and output FIFO buffers, 32 Ks input, 16 Ks output capacity
    • 24DSI16WRC
      The 16-channel 24DSI16WRC analog input module provides high-density 24-bit analog input resources on a standard single-width PMC. Optimized for flexibility and performance, the board is ideal for a wide variety of applications, ranging from simple precision voltage measurements, to the analysis of complex audio signals and waveforms. (+)

      Features:

      292763604861575915.jpg
      • Any PMC board can be used on PCI Express, PCI-X, cPCI-X, PCI, cPCI, PC/104-Plus via an adapter.
      • 16 wide-range differential 24-Bit simultaneously-sampled analog input channels.
      • Input sample rates to 105 Kilosamples per second per channel.
    • PC/104-ADADIO
      12-channel board for PC/104-Plus (+)

      Features:

      11893.jpg
      • High-resolution 16-bit analog input
      • Analog output and digital I/O
      • Samples eight analog input channels simultaneously
    • PMC-16AIO168
      16-bit analog I/O, 16 single ended or 8 differential input channels, 32-K sample FIFO buffers (+)

      Features:

      • A cost effective, high-speed 16-bit analog input/ output and digital output board
      • Eight analog output channels (at 300,000 samples/ sec per channel) are updated either synchronously or asynchronously, and support arbitrary waveform generation
      • The analog inputs are configurable as either 16 single-ended or 8 differential input channels, and can be scanned continuously or in bursts
  • Precision Devices  (1)
    • VC40
      High frequency Voltage-Controlled Crystal Oscillator (VCXO) for 4G wireless and high-speed data applications (+)

      Features:

      • The VC40 covers the frequency range from 60MHz to 800MHz, making it suitable for a wide range of applications including 4G wireless infrastructure, instrumentation and other high-speed data applications
      • Can be adjusted by as much as +/-100ppm via the voltage adjustment pin, over a tuning range of 0V to 3.3V
      • Stability is from +/-50ppm over an operating temperature range of -40°C to +85°C
  • Communications Computer Intelligence Integration  (2)
    • CCII Vehicle Management & Monitoring PMC
      Provides an integrated solution for monitoring and reporting the geographic position, movement parameters, and internal health of a vehicle (+)

      Features:

      • Incorporates a GPS module, a GSM module, autonomous data logging to onboard EEPROM, digital/analogue input and digital output functionality
      • An onboard rules engine allows easy and powerful user configuration
      • All VMM functions can be accessed using a powerful serial API
    • CCII Vehicle Management & Monitoring CCPMC
      Provides an integrated solution for monitoring and reporting the geographic position, movement parameters, and internal health of a vehicle (+)

      Features:

      • Incorporates a GPS module, a GSM module, autonomous data logging to onboard EEPROM, digital/analogue input and digital output functionality
      • An onboard rules engine allows easy and powerful user configuration
      • All VMM functions can be accessed using a powerful serial Application Program Interface
  • Analog Devices, Inc.  (9)
    • ADuC702x
      A single-chip, precision analog microcontroller solution that integrates a 12-bit analog front end with a 32-bit RISC processing core for industrial, optical networking, and automotive applications (+)

      Features:

      • Integrates an ARM7TDMI core with a Flash-based 16/32-bit RISC MCU with processing capabilities up to 45 MIPS peak performance
      • Analog peripherals include up to 16 channels of fast, 12-bit accurate analog-to-digital conversion, up to four individual 12-bit monotonic digital-to-analog converters, and a precision bandgap reference
      • Other peripherals include a comparator, programmable logic array (PLA), and a three-phase PWM generator
    • AD9736
      A 14-bit digital-to-analog converter (DAC) that clocks at a sample rate of 1.2 GSps (+)

      Features:

      • Operates from 1.8V and 3.3V supplies, consuming 380mW at 1.2 GSps with the interpolation filter bypassed and 550mW with the interpolation filter enabled
      • Provides a fast LVDS input interface using a DDR mode
      • Output currents are programmable over a range of 10mA to 30mA and can be configured for various single-ended or differential circuit topologies
    • AD5641
      A digital-to-analog converter (DAC) (+)

      Features:

      • Part of the nanoDAC family; small package and low power consumption
      • SC-70 package
      • 14-bit resolution
    • AD77990/91 and AD7788/89
      A low-power, 24-bit, sigma-delta analog-to-digital converter (+)

      Features:

      • Consumes only 25µA
      • Available in a MCOP-10 package
      • On-chip buffer and internal clock generator
    • AD7686
      A 16-bit Successive-Approximation Register (SAR), analog-to-digital converter (+)

      Features:

      • Housed in a 5mm x 3mm MSOP (micro-SOIC) package
      • Operates at 550 Ksamples/sec while providing ±3 LSB linearity
      • Typical power dissipation of 20mW with a 2.7V supply
    • AD9956
      A low-power, monolithic radio frequency (RF) synthesizer that integrates both direct digital synthesis (DDS) and phased locked loop (PLL) circuitry (+)

      Features:

      • Part of the AgileRF family of synthesizers
      • Operates in the ISM band of frequencies
      • 650-MHz, PECL-compliant CML clock driver with programmable slew rates
    • AD5380/AD5382
      A family of high-density digital-to-analog converters (DACs) (+)

      Features:

      • 40-channel (AD5380) or 32-channel (AD5382) 14-bit, voltage-output DAC operates from a single 5V power supply
      • On-chip, low-drift reference
      • User-programmable offset and gain for digital range adjustment and system calibration
    • AD534x Family
      A family of low-voltage, octal, digital-to-analog converters (+)

      Features:

      • Each device integrates eight low-power, parallel-interface DACs
      • Available in 6mm x 6mm chip-scale packages (CSP)
      • Available in 8-bit (AD5346), 10-bit (AD5347), and 12-bit (AD5348) versions
    • ADSP EZ-ICE
      In-circuit emulator for Analog Devices ADSP-2171 DSP (+)

      Features:

      • Contains GUI for easier debugging control
      • Plugs directly into processor socket on target board
      • Stand alone operation for software debugging
  • Toradex  (1)
    • NVIDIA Tegra 2 Computer on Module - Colibri T20
      The Colibri T20 module provides dual display support and a wide variety of display interface options, including digital RGB, analogue VGA, DVI (TDMS), and with an appropriate external encoder, LVDS, making interfacing to almost any LCD panel simple. The digital RGB interface supports resolutions of up to WSXGA+ (1680x1050), while the DVI interface will support Full HD (1920x1080) resolution. 4 and 5-wire resistive touch screens are natively supported. An integrated 16 bit stereo codec provides audio recording and playback functionality. The module can also be directly connected to a CMOS camera sensor for imaging application support. In addition to this rich set of features, the Colibri T20 provides full 100 Megabit Ethernet connectivity as well as high-speed USB 2.0 host and device functionality. The Colibri T20 IT module is a special version which meets the stringent requirement of an industrial temperature range (-40 to +85 degree Celsius). FEATURES: The Colibri T20 is part of the Colibri (ARM based) product family. The T20 module is based on NVIDIA's Tegra 2 ARM Cortex A9 MPCORE Dual Core processor, runs at 1.0GHz and was the first computer-on-module to feature this processor within the embedded market. Colibri modules feature state of the art technology, and are aimed at low power systems that require high CPU performance. They are equipped with all the interfaces needed in a modern embedded device. The T20 is available with 256 MB or 512 MB of on-board Flash memory. This provides a large amount of storage for program and data, with data storage further expandable through USB and SD Card. [...] (+)

      Features:

  • Memec  (1)
    • P160 Communications Module 3 Kit
      Ideal for Xilinx embedded MicroBlaze eystems (+)

      Features:

      19946.jpg
      • Adds Ethernet, Bluetooth, and analog I/O to Popular Memec Spartan-3 LC Board
      • Small, low-cost daughter card form-factor
      • Enables designers to add a standard set of processor peripherals and bulk memory to any P160 compatible system board
  • Precision Analog Systems (PAS)  (15)
    • PAS 9816/RO
      A 16-channel, 16- bit VME-based analog output card (+)

      Features:

      • Each of the 16 channels provides a dedicated 16-bit digital-to-analog converter (DAC)
      • Output voltage is +/- 10 V at 5 mA of output current
      • Double buffered DAC input registers allow all DAC outputs to be updated simultaneously
    • PAS 9710/AO
      8 Channels of +/- 10 Volt Analog Outputs (+)

      Features:

      • 14 bit resolution, 14 bit linear Digital to Analog Converter (DAC) per channel
      • Output current of +/- 5 mAmps per channel, Output Impedance of 0.1 Ohm
      • Settling time of 2 uSec for full scale voltage step
    • PAS 9737/AI
      64 differential analog input channels (+)

      Features:

      • Differential or single ended inputs jumper configurable per channel
      • Optional low pass filters with corner frequencies of 10 Hz, 50 Hz, 100 Hz or 500 Hz
      • Analog inputs on 2 ea. 64 position connectors, allows the use of mass termination cable
    • PAS 9416/AO & 9418/AO
      16 analog amplifiers with offset voltage circuits (+)

      Features:

      • Pin compatible with Precision Analog Systems' 9716/AO 16-channel, 16-bit analog output board
      • Using the combination of these two cards, a VMEbus-based analog output system can be constructed that will supply up to ±85V and up to 50 mA of output current per channel [...]
    • PAS9715/AO
      A 32-channel, 12-bit resolution D/A converter board (+)

      Features:

      • Each channel has a separate D/A and provides six program-selectable output ranges from ±10V to 0-2.5V
      • Supports full 32-bit VMEbus address space
      • 16-bit and 32-bit data transfers
    • PAS 9723/AI
      32 simultaneous sampling analog voltage input channels (+)

      Features:

      • 32 channel scanning analog multiplexer and 12 bit A/D Converter
      • Instrumentation Amplifier per channel with resistor programmable gain
      • Selectable +/- 10.24 V, +/- 5.12 V, 0-10.24 V, or 0 to 5.12V, input voltage ranges
    • PAS 9716/AO
      A 16-channel, 16-bit analog output board (+)

      Features:

      • Each channel has a separate D/A converter and provides a ±10V output range
      • Two D/A channels can be updated with a single 32-bit-wide VMEbus write operation
      • D/A converters reset to zero during powerup
    • 9716/AO
      Sixteen ±10V analog output channels with a 14-bit linear D/A converter per channel (+)

      Features:

      • Output current of ±5 mA
      • Output impedance 0.1 Ω
      • Output short circuit proof to analog ground
    • PAS 9422/AO
      Sixteen high power amplifier circuits on a 6U format card (+)

      Features:

      • Compatible with the PAS 9716/AO, 16 channel, 16 bit Analog Output card and the PAS 9715/AO, 32 channel, 12 bit Analog Output card
      • Will supply up to +/- 210 Volts and up to 200 mAmps of output current
      • Amplifiers can be configured for either inverting or non-inverting operation, with soldered in jumpers [...]
    • PAS 9732/AI
      8 channel, 0 to 10 Volt (9732) or +/- 10 Volt (9732-001), 14 bit Analog Input Card 3 MHz per channel continuous sampling on all channels (+)

      Features:

      • VME 6U form factor; 233 mm x 160 mm card size
      • VME access: D32, D16; A32, A24, A16
      • Right justified sixteen bit integer data. Digital input looks like contiguous memory
    • PAS 9915/AO
      VME Analog Output Card (+)

      Features:

      • Provides 32, 12-bit analog voltage output channels on a 6U VMEbus card
      • DAC resolution: 12 bits
      • VME Interface: A32, A24, A16; D32, D16 slave, no interrupts
    • PAS 9739/AI
      Thirty-nine channel, photodetector and dual gain analog input card (+)

      Features:

      • Dual gain amplifiers provide high and low sensitivity outputs for each photodiode
      • Thirteen synchronously scanning ADC chips
      • High and low sensitivity outputs of each channel are converted simultaneously
    • PAS 9722/AI
      Analog input board (+)

      Features:

      • 4 or 8 channels
      • 12-bit resolution
      • Samples at 800 KHz per channel
    • PAS 9731/AI
      8 channel, 14-bit resolution, 2 MHz per channel A/D converter board (+)

      Features:

      • Input voltage range of ±10V
      • 32-bit VMEbus interface allows two channels to be read with one transfer
      • No VMEbus interrupts [...]
    • PAS 9416/AO
      16 Amplified and Offset Channels (+)

      Features:

      • Output Drive of up to +/- 35Volts and +/- 20 mAmps
      • Gain of 1 or 2 Jumper Selectable
      • External Supply Voltage of +/- 15 Volts to +/- 45 Volts
  • Advantech Corporation  (14)
    • PCI-1744e
      \High-Speed Analog Input Card with PCI Express Interface (+)

      Features:

      • PCIe-1744 4-channel, 12-bit, ultra high-speed analog data acquisition card with PCI express interface
      • The PCIe-1744 is capable of handling analog-to-digital sampling simultaneously and independently on all four channels
      • The PCIe-1744 features multiple trigger modes for convenient application scenarios and a 30MHz sampling rate is achieved with independent A/D converters for each of the four analog input channels
    • PCM-3813I
      Advantech Launches Isolated Analog Input PCI-104 Card (+)

      Features:

      42559.jpg
      • The Industrial Automation Group of Advantech introduces the PCM-3813I PCI-104 module with 100 kS/s, 12-bit 32-channel isolated analog input
      • The PCM-3813I offers 2,500 VDC isolation protection and software programmable gain on each analog input channel protecting computers and connected peripherals from high voltage damage on the input lines
      • Moreover, the PCM-3813I breaks the traditional limitations of analog input data transmission by providing significantly faster speeds than similar modules on the market
    • MIC-3723
      16-bit, 8-channel non-isolated analog output card (+)

      Features:

      • 3U CompactPCI 16-bit 8-channel non-isolated analog output card
      • Each analog output channel is equipped with a 16-bit double-buffered DAC and features an auto-calibration function and BoardID switch
      • The MIC-3723 is a plug & play device that fully complies with the PCI specification Rev 2.2
    • ADAM-4117
      The ADAM-4117 is an 8-channel analog input module starting at $375. (+)

      Features:

      • The Industrial Automation Group of Advantech introduces the ADAM-4117, a data acquisition module designed for reliable operation in harsh environments. Its built-in microprocessor, encased in rugged industrial-grade ABS plastic, provides intelligent signal conditioning, analog I/O, digital I/O, LED data display, and an address mode with a user-friendly design.
      • Other ADAM-4117 features include: 8 differential and independently configurable channels, high noise immunity, broad power input range (+10~48VDC), LED display, and on-line firmware update. It supports both unipolar and bipolar inputs and has 1 kV surge protection on the power input, 3 kV ETF, and 8 kV ESD protection. It supports the popular Modbus/RTU protocol as well a simple ASCII based protocol.
      • The ADAM-4117 starts at $375 and is available for purchase directly from Advantech at 1-800-205-7940 or from one of Advantech's North American distributors at www.eautomationpro.com/us. [...]
    • USB-4716
      A 200 KSps 16-bit multifunction USB 2.0 I/O module (+)

      Features:

      32994.jpg
      • Designed for industrial environments
      • Includes a USB connector with screw fasteners and a DIN-rail mounting kit
      • Draws power directly from the USB port and therefore does not require an external power supply
    • MIC-3714
      3 FPM 2 TPC 12-bit A/D converter up to 30 MSps (+)

      Features:

      • 4 single-ended analog input channels
      • Programmable gain for each input channel
      • 32 K samples on board FIFO memory per channel
    • PCI-1727U
      The eAutomation Group of Advantech introduces the PCI-1727U analog output PCI card featuring 12 analog output channels with DB-37 connector. The PCI-1727U is capable of outputting +/- 10V and 0~20mA current loops with 14-bit resolution. It's equipped with 16 TTL DI and 16 TTL DO channels that are suitable for industrial control applications and a universal PCI bus compatible with both 3.3V and 5V signaling. (+)

      Features:

      • The PCI-1727U is compatible with Advantech's popular ISA card functions, connectors, and Windows DLL drivers allowing you to upgrade from ISA to PCI effortlessly. The ISA-compatible card uses the same software API as ISA cards, there is no need to rewrite programming when upgrading. The PCI-1727U features synchronized analog output function allowing multiple devices to be driven simultaneously without any synchronization lags.
      • The PCI-1727U starts at $795 and is available for purchase directly from Advantech at 1-800-205-7940. [...]
    • PEC-3710
      Integrated I/O controller (+)

      Features:

      52367.jpg
      • AMD LX800 500 MHz controller
      • 16-channel analog input
      • 4-channel analog output
    • Analog Input Module, 8-channel Independent
      Independent channel configuration allows up to eight types of signals to be processed by a single module. With older modules, each different type of signal required a separate module. (+)

      Features:

      • "The biggest advantage of this upgrade is that it will save you modules," says Mike Berryman, ADAM product manager. "You can take eight different types of analog inputs and pipe them into one module, and it'll pump out all the data in Modbus(R) to whatever software you like."
      • The ADAM-4019+ is a 16-bit, 8-differential channel analog input module with a 10Hz sampling rate. Its 4~20 mA input range satisfies most requirements in industrial automation applications.
      • Other frequently used input ranges include +/-10V, mV, and thermocouple, which are integrated into the ADAM-4019+.
    • USB-4704
      Data acquisition module (+)

      Features:

      45607.jpg
      • The USB-4704 is a 48 kS/s, 14-bit, 8-channel multi-functional module with analog I/O, digital I/O and counter functions specifically recommended for students or trainees
      • It comes packaged with Wavescan, a data logging tool that provides examples such as Visual C++, Visual Basic, Visual C#, Visual Basic .NET, Borland C++ builder, Delphi, and LabView for easy development
      • The USB-4704 has a price of $190, making this multi-functional USB module an excellent option for consumers looking for a low cost personal measurement tool [...]
    • PCI-1742U
      One MSps, 16-bit, 16-channel multifunction DAQ card (+)

      Features:

      32973.jpg
      • High-resolution multifunction DAQ card with fast sampling rate for PCI bus
      • 16x single-ended or 8x differential analog input channels, 1.0 MSps single channel sampling rate (800 KSps multi-channel), 2 x 16-bit D/A output channels, 16 x digital input/output channels, and 1 x 10 MHz 16-bit counter channel
      • 1K analog input FIFO
    • BACnet
      Four BACnet I/O Modules (+)

      Features:

      47712.jpg
      • BAS-3018BC 8-channel Universal Input Module
      • BAS-3024BC 4-channel Universal Input
      • 4-channel Analog Output
    • PCI-1739U
      A 48-channel digital I/O universal PCI card for both 3.3 V and 5 V PCI bus signaling (+)

      Features:

      32668.jpg
      • Uses popular Opto-22 compatible 50-pin connectors for interfacing to many signal conditioning and termination options
      • Features an interrupt function that can output a digital signal synchronized with an internal PC interrupt generated by the card
      • Other features include software configurable digital I/O channels, 0 to 65 °C operating temperature, and digital output status read-back
    • FPM-3121G
      Industrial 12.1-inch XGA flat panel monitor (+)

      Features:

      32478.jpg
      • 1024 x 768 resolution
      • Designed for applications with limited space
      • Direct-VGA signal input with a high level of compatibility
  • National Semiconductor  (3)
    • ADC12040
      A monolithic CMOS analog-to-digital converter (+)

      Features:

      • Converts analog input signals into 12-bit digital words at a minimum of 40 MSPS
      • Uses a differential, pipelined architecture with digital error correction and an on-chip sample-and-hold circuit to minimize die size and power consumption
      • Operates on a single 5V power supply
    • ADC08200
      A low-power 8-bit monolithic analog-to-digital converter with an on-chip track and hold (+)

      Features:

      • Operates at conversion rates up to 230 MSPS
      • Achieves 7.3 effective bits with 50 MHz input frequency
      • Typically consumes 210mW at 200 MSPS
    • LM96511
      Eight-channel transmit/receive system (+)

      Features:

      46222.jpg
      • Four ICs including an Analog Front End (AFE), transmit/receive switch, transmit pulser, and transmit beamformer
      • National claims this AFE has the highest-resolution digital variable gain amp available, with better channel-to-channel matching and higher spectral performance than analog-only solutions
      • An evaluation kit for the transmit/receive system includes WaveVision 5 software [...]
  • SSV Software Systems GmbH  (3)
    • AIO104-30
      A PC/104-based analog I/O board (+)

      Features:

      • 16 channels of 12-bit ADC
      • Two channels of 12-bit DAC
      • Eight digital inputs
    • AIO104-10
      A PC/104-based analog I/O board (+)

      Features:

      • 16-channel
      • 12-bit ADC
      • 0V to 10V
    • AIO104-20
      A PC/104-based analog I/O board (+)

      Features:

      • 2-channel
      • 12-bit DAC
      • 0V to 10V
  • HARTING  (2)
    • Mini Coax Single Row
      analogue signal transmission up to 4.5GHz (+)

      Features:

      • ganged RF-connector
      • 50 ohms
      • 15mm slot distance
    • Mini Coax Slim Version
      analogue signal transmission up to 2.5GHz (+)

      Features:

      • 50 Ohms
      • ganged RF connector
      • 9.5mm height against 13mm height of standard version
  • Nallatech  (3)
    • BenADDA-V4
      Virtex-4, Dual 105 MSps ADC, Dual 160 MSps DAC DIME-II Module (+)

      Features:

      31732.jpg
      • Suited for applications requiring high-speed analog capture and the processing performance of an on-board FPGA
      • Combining an Xilinx Virtex-4 SX or LX FPGA, two analog input channels, two analog output channels, and two banks of DDR-II SRAM, the module provides processing, analog I/O, and memory expansion capability
      • The direct coupling and high density coupling of processing, memory in less space makes design implementation easier [...]
    • BenADC-V4
      Virtex-4/Quad 250 MSps Analog Capture Module (+)

      Features:

      31733.jpg
      • Suitable for applications requiring high-speed analog capture and the on-board FPGA
      • Combining an Xilinx Virtex-4 SX or LX FPGA, four high speed analog capture channels, and two banks of DDR-II SRAM, the module provides processing, analog I/O, and memory expansion capability
      • The high density of processing and analog capture enables systems to be implemented in less space and makes design implementation easier
    • XMC-240
      FPGA processing and analog input PMC/XMC mezzanine (+)

      Features:

      42876.jpg
      • Designed to meet the signal processing needs of modern signal intelligence, software defined radio and radar applications
      • The XMC-240 is the latest product to be introduced to the highly successful Nallatech REVX Series of rugged embedded processing solutions
      • The XMC-240 features four channels of analog input that can sample analog signals at up to 250 MSPS with 14 bits resolution
  • Aitech Defense Systems  (3)
    • M453
      An analog I/O PMC module (+)

      Features:

      15665.jpg
      • 50 analog input channels
      • 16-bit A/D conversions at 100 Ksamples/sec
      • 12 differential or 24 single-ended analog input channels with ±10V input range
    • S930 I/O Card
      Rad-tolerant 3U, CompactPCI analog I/O card that increase real-time communication and I/O functions between control subsystems and external subsystems (+)

      Features:

      33260.jpg
      • Designed for LEO, Mars Terrestrial with an Option for GEO Environments
      • Single-Slot Conduction-Cooled 3U CompactPCI card
      • 12-bit A/D converter with -10 V to +10 V input range
    • M585 Multi-standard Graphics/Video PMC
      High-performance 2D and 3D graphics combined with extensive video I/O capabilities (Permedia3 graphics processor) (+)

      Features:

      • 32 MB SDRAM frame buffer memory
      • RGB/RGsB analog output support resolution up to 1600x1200; analog video inputs supporting composite, S-video and RGB/RGsB; composite video/S-video outputs supporting NTSC or PAL (according to configuration)
      • Flat panel interface supporting up to UXGA, DVI compliant
  • Curtiss-Wright  (12)
    • VPX3-535 3U VPX ADC DAC 6 GSPS
      The VPX3-535 combines high-speed multi-channel analog IO, VITA 48.8 Air-Flow Through (AFT) technology, user programmable FPGA processing and local processing in a single 3U VPX slot for direct RF wideband processing to 6Gsps. This card allows for a high performance single slot transceiver with two 6Gsps 12bit channel, to over 6GHz instantaneous analog bandwidth, but can also scale to larger system with many channel. The architecture is optimized for RADAR, Electronic Warfare (EW), Signal Intelligence (SIGINT), Radar Warning Receivers (RWR) & Software Defined Radio (SDR). (+)

      Features:

      • 3U VPX ADC DAC Card with Xilinx UltraScale FPGA
      • 2x 6Gsps/12b analog inputs (or 4x 3Gsps/12b)
      • 2x 6Gsps/12b analog outputs
    • FMC-520 DAC
      The FMC-520 DAC dual/quad channel digital-to-analog converter card, that can support up to 4 analog output channels updating at 500 MSPS or 2 analog output channels at 1 GSPS (+)

      Features:

      43574.jpg
      • Dual Texas Instruments DAC5682Z 16-bit digital-to-analog converters
      • Four (4) analog output channels updating at 500 MSPS or two (2) analog output channels updating at 1.0 GSPS
      • Choice of sample clock options: onboard, external direct or external 10 MHz reference
    • RVG-SA1 Analog Video Switch
      The Curtiss-Wright RVG-SA1 SWaP-C-optimized analog video switch implements analog crossbar functionality such that any of the 12 analog video inputs can be routed to any of the 12 outputs. The RVG-SA1 implements a digital crossbar to allow routing of 8 digital inputs to any of 8 digital outputs to support HSYNC and VSYNC connectivity for four PC-style analog video channels. In addition the RVG-SA1 supports four separate EDID interfaces, providing the ability to emulate displays. (+)

      Features:

      363759672405694361.jpg
      • Non-blocking, analog video cross point switch, 12 x 12
      • Up to 4 x RGBHV external video ports
      • 4x EDID ports to support computer inputs
    • Software Defined Radio & EW System
      Curtiss-Wright’s mid-size SDR and EW System enables customers to select their preferred RF tuner and software applications (i.e. GNU Radio, Red Hawk or SCA). By provides up to sixteen analog inputs (12-bit up to 2 Gsps) and eight (14-bit < 2.8 Gsps output channels), the SDR and EW system is easily able to interface L-band or S-band RF frequencies. The SDR/EW is built using rugged COTS products and the system is qualified to MIL-STD-810 and MIL-STD-461 standards. (+)

      Features:

      3745809954057398615.jpg
      • COTS Software Defined Radio and Electronic Warfare System with RF tuner and software selectable by the system integrator
      • Intel Core i7 or Xeon Processor
      • 28VDC Power input per MIL-STD-704
    • VPX3-534 3U VPX 6GSPS Tranceiver Card
      The VPX3-534 combines high-speed multi-channel analog IO, user programmable FPGA processing and local processing in a single 3U VPX slot for direct RF wideband processing to 6 Gsps. This card allows for a high performance single slot transceiver with two 6 Gsps 12bit channel, to over 6 GHz instantaneous analog bandwidth, but can also scale to larger system with many channel. The architecture is optimized for RADAR, Electronic Warfare (EW), Signal Intelligence (SIGINT), Radar Warning Receivers (RWR) and Software Defined Radio (SDR) applications. (+)

      Features:

      3928024634057507215.jpg
      • 3U VPX Analog I/O card with 2x 6Gsps/12b analog inputs (or 4x 3Gsps/12b)
      • Xilinx KU115 UltraScale user programmable FPGA
      • Xilinx ZU4 UltraScale+ Zynq
    • DSP-Based Data Acquisition Sub-Systems
      A line of multiprocessor DSP boards and modules integrated into complete data acquisition subsystems (+)

      Features:

      10633.jpg
      • Designed for industrial process and control applications
      • Deliver from 6400 MIPS fixed point DSP performance up to 16 GFLOPS floating point performance in a single 6U VMEbus or CompactPCI slot
      • Based on Ixthos' CHAMP architecture
    • PMC-704
      PMC-704 is a PCI Mezzanine Card (PMC) form factor, ruggedized, high-performance, feature rich Graphics PMC designed, developed and supported by Dy 4 Systems (+)

      Features:

      • Mobility 9000 Visual Processor Unit
      • Dual independent video capture capabilities
      • Dual analog capture
    • PMC-706
      A high-performance, ruggedized, feature-rich graphics PMC (+)

      Features:

      16660.jpg
      • ATI Technologies RADEON Mobility 9000 visual processor unit with: 64 Mbytes integrated high-speed DDR SDRAM, flexible power management capabilities, and hardware OpenGL acceleration
      • Dual independent analog and digital video output: NTSC, PAL, RS-170, and S-Video, non-interlaced analog, LVDS supporting OpenLDI/FlatLink and Barco, DVI/TMDS
      • Analog outputs support separate horizontal and vertical, composite, or sync on red/green/blue
    • DCU 4111 Data Concentrator Unit
      Designed to meet the most stringent aerospace requirements, the Curtiss-Wright Model 4111-1 Data Concentrator Unit (DCU) is a microprocessor based controller that receives a diverse assortment of inputs to process and format them into common digital data formats for consumption by various aircraft systems. The DCU design processes many digital communication protocols including EIA/TIA-422, ARINC 429 and Ethernet. (+)

      Features:

      320750269221207198.jpg
      • Rugged construction for military helicopter applications
      • Dual 28Vdc power Inputs normal and backup
      • Interfaces including: analog input, analog output, discrete arinc 429, ethernet, rs-232 [...]
    • Osiris Radar Input
      A high-performance, dual channel radar interface board that accepts and processes analog and digital radar signals (+)

      Features:

      34877.jpg
      • Provides a PCI interface to applications
      • Dual-channel radar interface card
      • PMC or half-length PCI form factors
    • PMC-704 Graphics
      PMC-704 - dual I/O graphics PMC (+)

      Features:

      • ATI Technologies RADEON Mobility 9000 Visual Processor
      • Dual independent video capture capabilities
      • Dual independent analog and digital video output
    • VPX3-4731 3U VPX Video Processor GPU
      The VPX3-4731 rugged NVIDIA Quadro Pascal P5000 based video processing 3U OpenVPX card was designed for high-performance video ingest, processing, and display applications. The 3U VPX module can capture up to 6 simultaneous video streams from analog and digital sources, and provides up to 4 simultaneous display outputs to DisplayPortâ„¢, DVI, HD/3G-SDI or analog CVBS output interfaces. (+)

      Features:

      4004092604058472488.jpg
      • NVIDIA Quadro Pascal P5000 Graphics / Video Processor in 3U OpenVPX form factor
      • 2048 CUDA cores, up to 6.2 TFLOPS
      • 16 GB GDDR5 256-bit graphics memory
  • CAEN Technologies,Inc.  (2)
    • V1742
      The Mod. V1742 is a VME board housing two sections of 16+1Channels 12bit 5GS/s Switched Capacitor Digitizer, with 1 Vpp input dynamic range on single ended MCX coaxial connectors. The DC offset adjustment (range ± 1V) on each channel by 16bit DAC allows a right sampling of a bipolar (Vin=± 0.5V) up to a full positive (Vin= 0 · +1V) or negative (Vin= 0 · -1V) analog input swing without losing dynamic resolution. The analog input signals are continuously sampled into the DRS4s (resolution up to 200ps) in a circular analog memory buffer (1024 cells). As a trigger signal arrives, all analog memory buffers are frozen and subsequently digitized with a resolution of 12bit into a digital memory buffer. The digital memory (128 events deep for each channel, where 1 event = 1024x12bit) allows to store following events, even if the readout is not yet started. Moreover, since the digital memory buffers work like FIFOs, the readout activity from VME or Optical Link doesn’t affect write operations of successive events. (+)

      Features:

      184331390941381821.jpg
      • A common board trigger can be provided via VME or Optical Link, or by TRGIN input.
      • 32+2 Channel in a 6U VME module
      • 12 bit; Selectable 5, 2.5, 1 GS/s Switched Capacitor ADC
    • V1724
      -8 channel -14 bit 100 MHz ADC with digital pulse processing (+)

      Features:

      • Analog Sum/Majority and digital over/under threshold flags for Global Trigger logic
      • Front panel clock In/Out available for multiboard synchronisation (direct feed through or PLL based synthesis)
      • Digital Pulse Processing for Spectroscopy Applications
  • GE Intelligent Platforms, Inc.  (15 of 21)
    • VMIVME-4116
      An 8-channel, 16-bit resolution analog output board (+)

      Features:

      • Fast settling: 10µs maximum to ±0.003 percent of FSR
      • Buffered voltage output (±10V at 5mA)
      • Multiplexed programmable outputs on P2 connector for testing analog outputs
    • ICS-150B
      4-Channel, 40 MHz, 12-bit, VMEbus Analog Input and output board (+)

      Features:

      33591.jpg
      • 4 separate 12-bit ADCs and DACs
      • The ADCs and DACs can operate at rates of up to 40 MHz/ch. for 2 channels, or 20 MHz/ch. for 4 channels
      • Continuous or burst modes of operation
    • VMIVME-4514A
      A scanning analog I/O board (+)

      Features:

      • 16 analog input channels
      • Continually digitizes all input channels and stores the results in a dedicated channel dual-port register (autoscanning mode)
      • Three A/D operating modes: autoscanning; random polling, and scanning poll
    • ICS-1556
      4-channel, 400 MHz 14-bit ADC PMC module with Virtex-5 SX95T user programmable FPGA (+)

      Features:

      • 4 transformer-coupled analog inputs
      • Analog-to-digital resolution 14-bits
      • Fs≤ 400 MHz per channel
    • VMIVME-4132
      An analog output board (+)

      Features:

      • 32 analog output channels
      • 12-bit D/A converter
      • One S&H for output
    • VMIVME-4512
      An analog I/O board (+)

      Features:

      • 16 analog input channels
      • Onboard 12-bit A/D converter
      • 16 differential or 16 single-ended channels
    • VMIVME-3125
      A 6U isolated scanning analog-to-digital converter board (+)

      Features:

      • 12-bits, 32-channels
      • Autoscanning; continuously digitizes inputs and stores results in dual-ported data registers
      • Input ranges from ±50mV to ±10V or 0 to 25mA
    • ICS-8145
      Rugged high-speed Acoustic VME Bus ADC board (+)

      Features:

      33572.jpg
      • 16 ADC channels (Analog Devices AD9260): 16-bits @ 2.5 MSPS
      • Rear I/O features differential analog inputs and FPDP II output bus
      • Onboard signal conditioning provides programmable gain, filtering
    • VMIVME-4105
      An 8-channel, 12-bit multiplying digital-to-analog converter board (+)

      Features:

      • Jumper-selectable P2 or front-panel outputs
      • 2- or 4-quadrant multiplier jumper-selectable option
      • Jumper option to support 8 independent or 1 shared AC or DC voltage reference
    • ICS-1554
      4-channel, 160 MHz 16-Bit ADC PMC module with Virtex-5 SX95T user programmable FPGA (+)

      Features:

      36712.jpg
      • Four AC-coupled analog inputs
      • Fs ≤ 160 MHz per channel
      • Xilinx Virtex-5 SX95T User Programmable FPGA
    • ICS-1554
      4-channel, 160 MHz 16-bit ADC PMC module with Virtex-5 SX95 user programmable FPGA (+)

      Features:

      • Four AC-coupled analog inputs
      • FS < 160 MHz per channel
      • Xilinx Virtex-5 SX95 User Programmable FPGA
    • daqNet
      Acoustic Data Conversion System (+)

      Features:

      33566.jpg
      • Fully integrated acoustic server in a compact rackmount 1U chassis
      • Up to 192 channels of acoustic I/O or 240 channels of digital I/O
      • Dual Gigabit Ethernet interfaces for data I/O and control
    • CAD16
      A 3U, intelligent 16 channel analog I/O board (+)

      Features:

      • Two 16-bit A/D converters
      • Programmable gain
      • Onboard TMS320C31 DSP [...]
    • VMIVME-3123
      A high-throughput analog input board (+)

      Features:

      • 16 differential analog input channels; software-selectable as 1, 2, 4, 8, or 16 active channels
      • 16-bit A/D converters; 1 per channel
      • Simultaneous sample-and-hold inputs
    • VMIVME-3413
      32 differential or single-ended low-level analog input channels (+)

      Features:

      • Buffered high-level analog outputs
      • Isolation from VMEbus; 500 VDC
      • Analog current loop inputs (optional)
  • Agilent Technologies  (3)
    • E1430A
      2 pass, or subranging, 10 Msamples/sec ADC with 23 bits of resolution (+)

      Features:

      • A single-slot, single channel, C-size, VXI card that is a complete A/D module
      • Included in the module with the low distortion, low noise analog to digital converter, is flexible input signal conditioning, tunable digital filtering, an 8-Mbyte memory, and a high-speed local bus
      • Input signal conditioning includes 11 attenuation/gain ranges, AC/DC coupling and an analog anti-alias filter
    • N8211A
      20/40 GHz performance analog upconverter generates a stimulus signal with superior AM, FM and pulse modulation capabilities (external or internal modulation) (+)

      Features:

      • Based on the PSG analog signal generator's high output power, low phase noise and excellent level accuracy [...]
    • ADS software
      An EDA platform for microwave and RF circuit and system design (+)

      Features:

      • Offers complete design integration to designers of cellular and portable products
      • Verilog-AMS co-simulation for simulating end-to-end system behavior with analog and digital components
      • W-Element Model for including RLGC files in simulations
  • TEWS Technologies LLC  (7)
    • TAMC900-10
      High speed, high-performance A/D converter AdvancedMC with eight high speed ADCs, preprocessing power by a Virtex-5 FPGA, high speed on board memory for full bandwidth snapshots (+)

      Features:

      38367.jpg
      • Form factor: PCIMG AMC.1 Module, x8 PCI Express port (AMC.1 Type 8 compliant)
      • Virtex-5 LXT FPGA
      • 4 MB QDR-II SRAM
    • TAMC 900
      The TAMC900 is an analog to digital converter AdvancedMC with 8 high speed ADCs providing preprocessing power by a Virtex-5 FPGA and high-speed onboard memory (+)

      Features:

      38072.jpg
      • Single-width / mid-height AMC.1 Type 8 compliant module, x8 PCIe port; IPMI interface
      • Virtex-5 LXT FPGA; 4 MB QDR-II SRAM
      • Analog-to-Digital Converter: 8 x LTC 2254 ADCs, 105 MSps, 14 bit
    • TCP467
      Suitable for high-density I/O in embedded applications (+)

      Features:

      31174.jpg
      • 32 single-ended or 16 differential channels of 16 bit multiplexed analog input, 8 channels of 16 bit analog output, 16 digital I/O lines, and a 32 bit multipurpose counter
      • Manual mode, sequencer mode, or external trigger for ADC/DAC
      • ± 10 V inputs/outputs
    • TAMC900
      High performance analog to digital converter AdvancedMC (+)

      Features:

      • Virtex-5 FPGA and high-speed onboard memory
      • Single-width, mid-height PICMG AMC.1 module; x8 PCI port (AMC.1 Type 8 compliant)
      • Virtex-5 LXT FPGA; 4 MB QDR-II SRAM
    • TIP551
      An IndustryPack compatible module offering 4 channels of isolated 16 bit analog outputs (+)

      Features:

      18122.jpg
      • Interface according to IndustryPack specification
      • Identification-PROM supports auto-configuration
      • Single Size IndustryPack
    • TPMC551
      A standard single-width 32-bit PMC module conforming to IEEE P1386.1 (+)

      Features:

      10967.jpg
      • PCI 2.1 compliant interface
      • Board size: 149mm x 74mm
      • Eight or 4 channels of isolated 16-bit analog outputs
    • TPMC550
      A standard single-width 32 bit PMC module conforming to IEEE P1386.1 (+)

      Features:

      17833.jpg
      • PCI 2.1 compliant interface
      • Board size: 149mm x 74mm
      • Eight or four channels of isolated 12 bit analog outputs
  • EWA, Inc.  (1)
    • ADX 1480-4
      The ADX1480-4 offers four high speed analog-to-digital converter (ADC) channels on a single 6U VME Module. Each channel includes a 14-bit ADC with sampling rates to 80 MHz. (+)

      Features:

      • 4 Channels
      • Single-slot, 6U VME
      • 80 MHz, 14-bit sampling
  • Dallas Logic Corporation  (1)
    • FMC-ADC01
      A four-channel analog signal capture board based on Texas Instrument's ADS64xx family of analog-to-digital converters (ADCs) (+)

      Features:

      • Supports both 12- and 14-bit devices with sample rates ranging from 65 MSps to 125 MSps
      • Seven front bezel MMCX connectors and a low pin count (LPC) FMC connector provide the module's off-board connectivity
      • In addition to the four A/D inputs, the module has an external clock input, synchronization input, and synchronization output
  • Micro Technic A-S  (3)
    • PV-2019B
      A 12-bit data acquisition module with analog and digital I/Os (+)

      Features:

      • 8 analogue 0-20mA inputs
      • 8 opto-isolated digital inputs
      • 8 opto-isolated digital outputs
    • PV-2019
      A PC/104 board combining 16 voltage and eight current inputs (0-20mA) with 12-bit resolution of A/D and D/A (+)

      Features:

      • 16 analog voltage inputs, single-ended
      • Eight analog 0-20mA inputs
      • Two analog voltage/current outputs
    • Micronix PV-1800
      GSM/GPRS modem including 20 W power supply module with analog and digital I/O channels (+)

      Features:

      23595.jpg
      • GSM/GPRS modem: dual-band EGSM900/GSM1800; data, voice, SMS, and fax; control via AT commands
      • Power supply: 8 to 27 VDC input range; Output: 5V at 4A
      • Integrated I/O: 8 isolated analog inputs (0-10V), 12-bit; 8 digital inputs, opto-isolated; 7 digital outputs, opto-isolated
07/3/22 13:51
Close

Subscribe to Analog updates