Analog

Showing results for: continuous signal
Refine Analog companies and products:
analog analogue analog circuit analog ic analogue circuit analogue ic analog to digital digital to analog a/d d/a adc dac continuous signal
Click on any vendor
to see a listing of
continuous signal related products.
  • AcQ InduCom  (6)
    • VME381
      A DSP ADC for high-speed analog signal capturing and digital signal processing (+)

      Features:

      • 6U VMEbus board
      • Four TMS320C32 DSPs, each with 2 analog input channels, running at 60 MHz, delivering 30 MIPS
      • Two simultaneous sampling 12-bit A/D channels per DSP
    • VME383
      A DSP DAC for high-speed analog signal regeneration and digital signal processing (+)

      Features:

      • 6U VMEbus board
      • Four TMS320C32 floating point DSPs running at 60 MHz, delivering 30 MIPS
      • Three high-speed 16-bit D/A channels per DSP
    • CPCI381
      A 3U CompactPCI board providing a powerful platform for high-speed analog signal capturing and digital signal processing (+)

      Features:

      11141.jpg
      • TMS320C32 floating point DSP, running at 60 MHz, delivering 30 MIPS
      • Two simultaneous sampling 12-bit A/D channels
      • Programmable sampling rate up to 7.5 Msamples/sec
    • M383 DSP M-module
      Provides a powerful platform for high-speed analog signal (re) generation and digital signal processing (+)

      Features:

      • Three analog output channels share the 10 MSps output update rate
      • Local software allows enhanced and user-specific signal processing
      • Eight general-purpose digital I/Os (4x input, 4x output, TTL-compatible) are available [...]
    • M381 DSP M-module
      Provides a powerful platform for high-speed analog signal capturing and digital signal processing (+)

      Features:

      • Two analog input channels are capable of simultaneously sampling at (maximum) 7.5 MSps sampling rate
      • Local software allows enhanced and user-specific signal processing
      • Gain and offset errors are compensated by the DSP
    • CPCI383
      A 3U CompactPCI board providing a powerful platform for high-speed analog signal (re)generation and digital signal processing (+)

      Features:

      11143.jpg
      • TMS320C32 floating point DSP, running at 60 MHz, delivering 30 MIPS
      • Three high-speed, 16-bit D/A channels
      • Analog output rate is software programmable up to 7.5 Msamples/sec (using DMA, single channel)
  • ADLINK Technology, Inc.  (5)
    • PCI-9527
      The PCI-9527 is a high-performance, 2-CH analog input and 2-CH analog output dynamic signal acquisition board. This board is specifically designed for audio testing, acoustic measurement, and vibration analysis applications. The ADLINK PCI-9527 features two 24-bit simultaneous sampling analog input channels. The 24-bit sigmadelta ADC provides a sampling rate up to 432 KS/s at high resolutions, making it ideal for higher bandwidth dynamic signal measurements. The sampling rate can be adjusted by setting the onboard DDS clock source to an appropriate frequency. All channels are sampled simultaneously and accept an input range from ±40 V to ±0.316 V. The PCI-9527 analog input supports software selectable AC or DC coupling and 4 mA bias current for integrated electronic piezoelectric (IEPE) sensors. The ADLINK PCI-9527 also has two channels of 24-bit resolution, high fidelity analog output. The outputs occur simultaneously at software programmable rates up to 216 KS/s. A software programmable output range of ±0.1 V, ±1 V, and ±10 V is available on the output channels. (+)

      Features:

      183912127701794017.jpg
      • 24-Bit Sigma-Delta ADC and DAC
      • 2-CH simultaneous sampling analog input
      • 2-CH simultaneous updated analog input
    • PCIe-9842
      The ADLINK PCIe-9842 is a 200 MS/s 14-bit 1-CH digitizer designed for applications such as LIDAR testing, optical fiber testing, and radar signal acquisition. The 100 MHz bandwidth analog input with 50 ohm impedance is designed to receive ¡Ó1 V high speed signal. With this simplified front-end design and high stable onboard reference, the PCIe-9842 provides not only high accuracy measurement results but also delivers high dynamic performance. For applications that require data to be acquired and transferred in real-time, the PCIe-9842 utilizes the PCI Express x4 bus as its interface. When signals are converted from analog to digital data, the data will be transferred to host system memory continuously because of the high bandwidth of the PCI Express. For applications that require data to be acquired and transferred in real-time, the PCIe-9842 utilizes the PCI Express x4 bus as its interface. When signals are converted from analog to digital data, the data will be transferred to host system memory continuously because of the high bandwidth of the PCI Express. (+)

      Features:

      183913114701794017.jpg
      • Up to 200 MS/s sampling rate
      • High resolution 14-bit ADC
      • ±1 V Input range with 50 Ω input impedance and DC couple
    • USB DAQ modules
      Equipped with built-in signal conditioning, the USB-powered Plug and Play USB DAQ modules deliver easy connection and accurate results for both portable measurement and machine automation applications. Featuring built-in signal conditioning, ADLINK USB DAQ modules enable direct measurement of most frequently applied signal sources which reduce manpower requirements and associated development costs while increasing overall accuracy. ADLINK's USB DAQ collection offers the USB-1900 series, consisting of USB-1901 and USB-1902 models of 16-bit 250 kS/s DAQ modules. Also in the series is the USB-1903, with additional built-in precision current-to-voltage resistors allowing direct measurement of current signals from 0 to 20 mA. Rounding out the USB DAQ category is the USB-2401, a 24-bit four-channel simultaneous-sampling universal DAQ module supporting sampling rates up to 1.6 kS/s and a more flexible signal conditioning circuit such as voltage, current, strain, load cell, thermocouple, and RTD measurement. The USB DAQ line is ideally suited for easily accomplished deployment and superior accuracy when measuring temperature, stress, strain, and other factors in diverse applications. (+)

      Features:

      183911542701794017.jpg
      • USB 2.0 high-speed function
      • USB bus power
      • Removable screw-down terminal module
    • cPCI-8168
      A 6U, CompactPCI, 8-axis motion control card (+)

      Features:

      14479.jpg
      • Capable of integrating into six system cards to control up to 48 motors
      • Differential input/output signals
      • Generates high-frequency pulse trains that control motor speed and positioning
    • PCI-8134
      A high-performance, four-axis stepper and servo motion control card (+)

      Features:

      18486.jpg
      • Provides widely utilized pulse train for both stepping and AC/DC servo motors, with pulse rates up to 2.4 Mbps
      • Programmable acceleration and deceleration times
      • S-curve profile allows for smoother motion during starting and stopping
  • Agilent Technologies  (7)
    • E1430A
      2 pass, or subranging, 10 Msamples/sec ADC with 23 bits of resolution (+)

      Features:

      • A single-slot, single channel, C-size, VXI card that is a complete A/D module
      • Included in the module with the low distortion, low noise analog to digital converter, is flexible input signal conditioning, tunable digital filtering, an 8-Mbyte memory, and a high-speed local bus
      • Input signal conditioning includes 11 attenuation/gain ranges, AC/DC coupling and an analog anti-alias filter
    • N8211A
      20/40 GHz performance analog upconverter generates a stimulus signal with superior AM, FM and pulse modulation capabilities (external or internal modulation) (+)

      Features:

      • Based on the PSG analog signal generator's high output power, low phase noise and excellent level accuracy [...]
    • ADS software
      An EDA platform for microwave and RF circuit and system design (+)

      Features:

      • Offers complete design integration to designers of cellular and portable products
      • Verilog-AMS co-simulation for simulating end-to-end system behavior with analog and digital components
      • W-Element Model for including RLGC files in simulations
    • B4655A FPGA Dynamic Probe
      For visibility into FPGA´s internal activity (+)

      Features:

      • Up to 64 internal signals for each pin dedicated to debug
      • Ability to switch internal probe points in seconds
      • Maps internal signal naming from your FPGA design tool to your logic analyzer
    • 81600
      A Infiniium DCA oscilloscope (+)

      Features:

      • TDR capability enables verification of the signal integrity of printed circuit boards, cables, and connectors that incorporate InfiniBand technology
      • Plugins are available that provide up to 80 GHz bandwidth and single-ended and differential TDR measurements [...]
    • PSA-80BW
      A wide-bandwidth, vector spectrum analyzer solution (+)

      Features:

      • Provides 80-MHz demodulation bandwidth and eight-second capture memory for multi-carrier power amplifier (MCPA), signal monitoring, radar, and satellite measurement applications
      • Up to 20 GHz frequency coverage, 0.1dB amplitude flatness, 0.7 degree phase flatness, and optional 1.2 Gbyte (768 Msamples) deep capture memory to provide eight seconds of full-bandwidth capture at the maximum sample rate
      • Well suited for error vector modulation (EVM)
    • Infiniimax 1130A
      A 1.5 GHz differential probe (+)

      Features:

      17118.jpg
      • Can be paired with Agilent's Infiniium Mixed Signal (MSO) and Digital Signal Oscilloscopes (DSO) for validating and verifying the performance of new high-speed digital product designs
      • Single-ended or differential measurements from a single probe amplifier
      • Controlled transmission-line probe heads provide a flat frequency response over the entire bandwidth specification and eliminate the distortion and loading that affects probes with in-band resonance
  • Compel Electronics  (2)
    • Coaxial adapters for monitoring points
      For the direct type, the device is made up of three coaxial interfaces so that an input / output path for the signal in transit and a direct link for monitoring are created (+)

      Features:

      30429.jpg
      • For the uncoupled type, the device is also made up of three coaxial interfaces; the difference lies in the fact that the signal which is picked up to be monitored is uncoupled with respect to the signal in transit through the insertion of an internal resistor which has been appropriately connected
      • Sometimes there is also the need for better adaptation, from an electrical point of view, of the output port of the signal being monitored; in this case a further resistor is appropriately connected, thus obtaining an uncoupled and adapted link
      • As far as the interface coaxial connectors are concerned, the most common types used are the 1.0/2.3 and 1.6/5.6 (male or female)
    • BALUNS
      Impedance adapters allow systems with different impedance levels to be connected (+)

      Features:

      30182.jpg
      • As is well known, the best method for transmitting a signal is to transport it using means with uniform impedance: Any variation or discontinuity leads to great reflections and losses in the signal
      • In modern equipment the need often arises to connect systems with a 75 ohm output (typical in the use of coaxial cables) with systems with a 120 ohm output (typical when using twisted pairs which have been introduced because a high density of connections with cables of reduced dimensions is needed)
      • It becomes necessary, therefore, to adopt a device capable of connecting the two systems in such a way that each uses its own impedance, eliminating the possibility of having substantial losses in the signal
  • Cypress Semiconductor  (1)
    • PSoC 4
      PSoC 4 is a custom mixed-signal SoC with programmable analog and digital blocks combined with flexible routing and interconnects (+)

      Features:

      • A new Programmable System-on-Chip (PSoC) architecture from Cypress Semiconductor combines analog and digital fabric with CapSense capacitive touch technology and the 32-bit ARM Cortex-M0 core
      • PSoC 4 is a custom mixed-signal SoC with programmable analog and digital blocks combined with flexible routing and interconnects
      • For analog input, the chip features a high-performance successive-approximation analog-to-digital converter with 12-bit resolution sampling at 1 Msps
  • Diamond Systems Corporation  (1)
    • Ruby-MM-1616AP-XT
      The Ruby-MM-1616A family provides up to 16 channels of 16-bit resolution analog outputs with either voltage and/or current outputs. The modules also provide 48 lines of digital I/O, a waveform generator, 4 pulse width modulators, 2 counter/timers, and HART signal handling capability on four channels. This new family of analog output modules provides the highest accuracy analog outputs, making them ideal for embedded and OEM applications needing analog output with digital I/O. (+)

      Features:

      238154878641804264.jpg
      • 4, 8, or 16 16-bit analog outputs
      • Independent voltage and/or current outputs
      • 48 digital I/O lines
  • Electro Standards  (1)
    • M4331-200 CellMite
      An LVDT embedded conditioning board (+)

      Features:

      41571.jpg
      • Connects directly to two standard AC LVDT transducers and simultaneously generates a serial output for connection to a PC and a ± 10 V analog output
      • Onboard storage for up to three calibrated LVDTs, each with integrated six-point calibration that can be used to linearize the LVDT outputs
      • Its multidrop RS-232/RS-485 serial port and simple command set allow for connection of multiple units in a serial network configuration
  • Freescale Semiconductor  (1)
    • K50 32-bit MCU
      Integrated analog measurement engine consisting of operational and transimpedance amplifiers, then adds 16-bit ADC and 12-bit DAC modules for continuous processing of analog signals (+)

      Features:

      47503.jpg
      • On-chip interfaces for Ethernet
      • low-power LCD controller
      • Capacitive touch-sensing module
  • Fujitsu  (2)
    • CHArge-mode Interleaved Sampler
      Fujitsu 65 nm CMOS process technology (+)

      Features:

      • Resolution: 8-bit
      • Sampling rate: 56 GSps
      • Power supply: -1.2 V, 1.2 V, 3.3 V
    • FCN-260D
      A vertical board-mount I/O socket in the microGiGaCN connector series (+)

      Features:

      18253.jpg
      • Optimized for differential signal transmission of 3.125 Gbps and higher, over standard FR-4 material
      • Available in 4x and 12x versions with latches for InfiniBand applications
      • Intermatable with the series' existing cable-mount plug connectors
  • GE Intelligent Platforms, Inc.  (15 of 16)
    • ICS-150B
      4-Channel, 40 MHz, 12-bit, VMEbus Analog Input and output board (+)

      Features:

      33591.jpg
      • 4 separate 12-bit ADCs and DACs
      • The ADCs and DACs can operate at rates of up to 40 MHz/ch. for 2 channels, or 20 MHz/ch. for 4 channels
      • Continuous or burst modes of operation
    • ICS-1556
      4-channel, 400 MHz 14-bit ADC PMC module with Virtex-5 SX95T user programmable FPGA (+)

      Features:

      • 4 transformer-coupled analog inputs
      • Analog-to-digital resolution 14-bits
      • Fs≤ 400 MHz per channel
    • ICS-8145
      Rugged high-speed Acoustic VME Bus ADC board (+)

      Features:

      33572.jpg
      • 16 ADC channels (Analog Devices AD9260): 16-bits @ 2.5 MSPS
      • Rear I/O features differential analog inputs and FPDP II output bus
      • Onboard signal conditioning provides programmable gain, filtering
    • ICS-1554
      4-channel, 160 MHz 16-bit ADC PMC module with Virtex-5 SX95 user programmable FPGA (+)

      Features:

      • Four AC-coupled analog inputs
      • FS < 160 MHz per channel
      • Xilinx Virtex-5 SX95 User Programmable FPGA
    • ICS-1554
      4-channel, 160 MHz 16-Bit ADC PMC module with Virtex-5 SX95T user programmable FPGA (+)

      Features:

      36712.jpg
      • Four AC-coupled analog inputs
      • Fs ≤ 160 MHz per channel
      • Xilinx Virtex-5 SX95T User Programmable FPGA
    • ICS-8551
      The ICS-8551 is a rugged 4 or 2 channel, 1.5/3 GHz ADC XMC module intended for Software Defined Radio (SDR) applications (+)

      Features:

      36708.jpg
      • 4 AC-Coupled Analog Inputs
      • Fs ≤ 1.5 GHz 4-channel, or 3 GHz 2-channel (software selectable), 8-bit
      • Xilinx Virtex-4 User Programmable FPGA (FX60 or FX100)
    • VMIVME-3123
      A high-throughput analog input board (+)

      Features:

      • 16 differential analog input channels; software-selectable as 1, 2, 4, 8, or 16 active channels
      • 16-bit A/D converters; 1 per channel
      • Simultaneous sample-and-hold inputs
    • ICS-645D
      High-speed 32-Channel PCI ADC Board with Signal Conditioning (+)

      Features:

      33569.jpg
      • 32 ADC channels (Analog Devices AD9260): 16-bits @ 5 MSPS
      • Signal Bandwidth < 1.25 MHz
      • 64-bit, 66 MHz PCI interface (PCI 2.2 compliant), 400 MBps FPDP II interface
    • VMIVME-3413
      32 differential or single-ended low-level analog input channels (+)

      Features:

      • Buffered high-level analog outputs
      • Isolation from VMEbus; 500 VDC
      • Analog current loop inputs (optional)
    • ICS-8554D
      For use in communications, radar, and test and measurement applications in harsh environments (+)

      Features:

      33318.jpg
      • Suitable applications include military communications, signal intelligence, smart antenna, radar beam forming, wireless test and measurement and satellite ground stations
      • DC-coupled digital receiver
      • Four 14-bit ADCs that sample synchronously at frequencies up to 105 MHz
    • ICS-110BL
      24-bit, Sigma-Delta ADC board with optional signal conditioning (+)

      Features:

      33589.jpg
      • Up to 32 differential input channels
      • 24-bit sigma-delta A/D converters
      • Simultaneous sampling at rates up to 100 kHz/ch.
    • ICS-130
      32-channel, 1.2 MHz/ch. 16-bit, Sigma-Delta ADC board (+)

      Features:

      33593.jpg
      • 32 differential inputs
      • Little or no anti-aliasing required
      • Simultaneous sampling
    • AXISLib-CL
      AXISLib-CL Signal and Vector Processing Library providing digital signal processing and mathematical functions (+)

      Features:

      • Comprehensive signal and vector processing functionality
      • Accelerates engineering development
      • Both industry standard VSIPL and proprietary AXISLib0RSPL API provided
    • ICS-625B
      32-Channel, 288 kHz/ch. PCI Bus DAC board (+)

      Features:

      33587.jpg
      • Up to 32 separate 24-bit DACs
      • Reduced reconstruction filter requirement
      • Simultaneous sampling across all channels on single or multiple boards
    • ICS-1650
      High-speed data acquisition and DSP engine for PCI Express-based desktop PCs and servers deployed in SIGINT, communications, radar, medical imaging, and T&M applications (+)

      Features:

      38089.jpg
      • 4-channel, 250 MHz 12-bit ADC
      • Transformer-coupled inputs
      • 50 ohm input impedance
  • General Standards Corporation  (15 of 16)
    • CPCI-16DSI-VHS
      A versatile multifunction analog I/O board (+)

      Features:

      • The board has 8 analog inputs and 8 analog outputs per board and supports arbitrary waveform generation
      • A single 16-bit scanning Analog-to-Digital converter scans 8 single-ended or 4 differential inputs at an aggregate rate of 72,500 samples per second into the 32,000 sample storage FIFO
      • Up to 250,000 samples per second aggregate output update rates for the 8 D/A channels. Analog outputs are double-buffered and allow for software or hardware (synchronized) strobes for output updating
    • PC104P-16AIO88
      Versatile multifunction analog I/O board for PC/104-Plus (+)

      Features:

      • Eight analog inputs
      • Eight analog outputs per board
      • Supports arbitrary waveform generation
    • PC104P-VIDEO-AI2
      PC-104-Plus analog video input (+)

      Features:

      • Two video digitizers, FIFOs, and a DMA engine
      • Each video digitizer provides luminance and chrominance signal processing for NTSC M, NTSC N, NTSC 4.43, NTSC-Japan, PAL BGHI, PAL N, PAL M, and SECAM
      • Once the interface has been initialized, it transfers frame-after-frame of video input to host memory without host intervention
    • cPCI-16AIO88
      Eight analog output channels with a 16-bit D/A converter per channel (+)

      Features:

      • 16-bit scanning ADC for 8 single-ended or 4 differential analog input channels
      • Input and output ranges available as ±10V, ±5V, or ±2.5V
      • Input and output FIFO buffers, 32 Ks input, 16 Ks output capacity
    • 24DSI16WRC
      The 16-channel 24DSI16WRC analog input module provides high-density 24-bit analog input resources on a standard single-width PMC. Optimized for flexibility and performance, the board is ideal for a wide variety of applications, ranging from simple precision voltage measurements, to the analysis of complex audio signals and waveforms. (+)

      Features:

      292763604861575915.jpg
      • Any PMC board can be used on PCI Express, PCI-X, cPCI-X, PCI, cPCI, PC/104-Plus via an adapter.
      • 16 wide-range differential 24-Bit simultaneously-sampled analog input channels.
      • Input sample rates to 105 Kilosamples per second per channel.
    • PMC66-16AISS16AO2
      16-Bit, 18-Channel, 1.0-MSPS PMC Analog Input/Output Board With 16 Simultaneously Sampled Analog Inputs, Two Analog Outputs, and Input Sampling Rates to 1.0 Msps per channel (+)

      Features:

      35126.jpg
      • The 16-Bit analog I/O module samples and digitizes 16 input channels simultaneously at rates up to 1.0 million samples per second per channel, and the resulting 16-bit sampled data is available to the PCI bus through a 256K-Sample FIFO buffer
      • Sampling can be controlled in groups of 1 through 16 channels, and the sample clock can be generated either from an internal rate generator, or by software or an external source
      • Both burst and continuous sampling modes are supported, and input ranges are software-selectable as ±10V, ±5V or ±2.5V
    • cPCI66-16AISS16AO2
      16-bit, 18-channel, 1.0-MSPS CompactPCI analog input/output board with 16 simultaneously sampled analog inputs, two analog outputs, and input sampling rates to 1.0 MSPS per channel (+)

      Features:

      • The 16-bit cPCI66-16AISS16AO2 analog I/O module samples and digitizes 16 input channels simultaneously at rates up to 1.0 million samples per second per channel, and the resulting 16-bit sampled data is available to the PCI bus through a 256K-Sample FIFO buffer
      • Sampling can be controlled in groups of 1 through 16 channels, and the sample clock can be generated either from an internal rate generator, or by software or an external source
      • Both burst and continuous sampling modes are supported, and input ranges are software-selectable as ±10V, ±5V, or ±2.5V
    • cPCI66-16AO16
      16 precision 3-wire balanced differential high-speed analog output channels (+)

      Features:

      25769.jpg
      • 16-bit resolution; D/A Converter per channel
      • 66 MHz PCI Bus support
      • Data rates to 440K samples per second per channel; 7.04 MSPS Aggregate Rate
    • PC104P-16AO2MF
      PC/104-Plus D/A board with 400 kHz-per-channel, high speed 16-bit analog outputs (+)

      Features:

      • Supports arbitrary waveform generation
      • Two analog output channels are updated independently from an internal buffer, either at software-determined rates or by an externally supplied clock
      • Flexible operating modes include continuous, periodic, and triggered burst functions, as well as the seamless, dynamic concatenation of waveforms in real time
    • cPCI-16AO12
      Provides 400 KHz-per-channel precision high speed 16-bit analog outputs, and supports arbitrary waveform generation (+)

      Features:

      • Twelve analog output channels are updated simultaneously from an internal buffer, either at a software-determined rate, or by an externally supplied clock
      • Flexible operating modes include continuous, periodic and triggered burst functions, as well as the seamless, dynamic concatenation of waveforms in real-time
      • Output ranges are supplied as ±10 V, ±5 V, or ±2.5 V
    • PC104P-16AO12
      PC/104-Plus D/A board with 400 KHz-per-channel, high-speed 16-bit analog outputs (+)

      Features:

      12832.jpg
      • Supports arbitrary waveform generation
      • 12 analog output channels are updated simultaneously from an internal buffer, either at a software-determined rate, or by an externally supplied clock
      • Flexible operating modes include continuous, periodic, and triggered burst functions, as well as the seamless, dynamic concatenation of waveforms in real time
    • PMC-16AO12
      A PMC D/A converter board (+)

      Features:

      • Provides 400-KHz/channel precision, high-spreed, 16-bit analog outputs and supports arbitrary waveform generation
      • 12 analog output channels are updated simultaneously from an internal buffer, either at a software-determined rate, or by an externally supplied clock
      • Opertaing modes include continuous, periodic, and triggered burst functions, as well as seamless dynamic concatenation of waveforms in real time
    • cPCI-16AO4MF
      Four precision 3-wire balanced differential high-speed analog output channels (+)

      Features:

      22049.jpg
      • 16-bit resolution; D/A converter per channel
      • Data rates to 400 KSps per channel; 800 KSps aggregate rate
      • Output ranges of ±12 V, ±10 V or ±5 V
    • cPCI-16AO2MF
      Two-channel 16-bit high-speed analog output PMC board (+)

      Features:

      • Two precision 3-wire balanced differential high-speed analog output channels
      • 16-bit resolution, D/A converter per channel
      • Data rates to 400 Ksps per channel, 800 Ksps aggregate rate
    • Bus Link
      A two-board set with a cable that allows the user to perform very high speed data transfers between any two machines with any mix of PMC, CompactPCI, or PCI (e.g. PC, Sun, SGI, etc.) (+)

      Features:

      • Burst transfers between boards at 100 Mbytes/sec and continuous transfers of 80 Mbytes/sec
      • Deep FIFOs (up to 500 Kbytes in each direction) support burst transfers and smooth continuous operation of the link
      • Linux and VxWorks available
  • Highland Technology, Inc.  (2)
    • V430
      Single-width 6U, B-size VXI module that provides 32 channels of input differential amplifiers, 32 simultaneously triggered sample-and-hold circuits, and a single scanning analog-to-digital converter that drives 32 separate VME-readable output data-registers (+)

      Features:

      • A common trigger-event initiates simultaneous sampling, sequential A/D conversion and data storage; this trigger may be an external pulse, a VMEbus command, or may be an internal free-running clock
      • Total conversion-time is below 125 microseconds
      • The V430 digitizes to 12-bit resolution, with full-scale signal-range selectable as 2's complement or offset binary
    • V360
      Intelligent, eight-channel, period/frequency/RPM measurement module for signal conditioning magnetic speed pickups, flowmeters, and encoders (+)

      Features:

      21149.jpg
      • Also use with AC line voltage or alternator windings, optical pickups, fuel flowmeters, contact closures, or other special levels
      • High noise immunity ensures accurate measurement in industrial and aerospace environments
      • Register-based, VXI compliant, 16-bit VME module with clean, simple architecture that simplifies programming
  • Informtest Ltd.  (2)
    • INTE074 (OSC4)
      A digital oscilloscope-digitizer (+)

      Features:

      • Performs 10-bit ADC on 1 and 2 inputs within ±0.5, ±5, and ±50V ranges
      • Performs 8-bit ADC on 3 inputs within ±25V range with programmable sampling period from 10 nsecs to 0.5ms (100 MHz–2 KHz)
      • Channels 1 and 2 are equal, providing differential signal input and storing in 1 Mbyte RAM
    • INTE083 (OSC2M)
      A digital oscilloscope with differential input (+)

      Features:

      • 10-bit ADC using 2 independent channels with differential inputs
      • Conversion results stored in 32 Kbytes onboard memory
      • Independent or mutual channels clocking from internal or external signal or programmable triggering available
  • Innovative Integration  (9)
    • X6-400M PMC/XMC Module
      Integrates high speed digitizing and signal generation with signal processing on a PMC/XMC I/O module with a powerful Xilinx Virtex-6 FPGA signal processing core, and high performance PCI Express/PCI host interface (+)

      Features:

      46507.jpg
      • The X6-400M features two 14-bit 400 MSPS A/Ds, either AC or DC-coupled, plus two 500 MSPS update rate DACs
      • The DAC can be used a single 1 GHz output channel
      • Receiver IF frequencies of up to 250 MHz are supported
    • ePC-nano Rugged Embedded Computer 5.9" x 3" XMC IO
      The ePC-nano – a user-customizable, turnkey computer with full Windows/ Linux PC functionality to provide autonomous operation of a huge assortment of FPGA-accelerated, analog I/O-equipped XMC modules. The ePC-nano is a conduction-cooled solution, engineered to ruggedization level 3, for use in vehicles or other mobile applications. Distributed Data Acquisition: Put the ePC-nano at the data source and reduce system errors and complexity. Limitless flexibility – embellish FPGA signal processing or swap XMC module to alter functionality. XMC site for I/O, userprogrammable FPGA for real-time DSP, ethernet for WAN system connectivity, dual mSATA for long-duration data logging/signal playback, GPS/IEEE-1588 supporting synchronous operation over large distances, USB ports to allow connectivity to ubiquitous peripheral devices. Remote or Local Operation: Continuous data streaming up to 500 MB/s (local SSDs) or 1 Gb/s Ethernet. A dual, 10 GbE expansion module will be available soon. Rugged: Boots OS from embedded 16 GB eMMC drive in a compact, rugged 150x75mm footprint that is ready for deeply embedded operation in a rugged environment. Perfect for portable or automotive battery operated RF data loggers, beam steering, LIDAR/RADAR or waveform synthesis applications powered via a 6-14V DC supply [...] (+)

      Features:

      333882733491719056.jpg
    • X6-1000M
      Integrates high-speed digitizing and signal generation with signal processing on a PMC/XMC IO module for demanding DSP applications. (+)

      Features:

      • Two 1 GSPS, 12-bit A/D channels
      • Two 1 GSPS, 16-bit DAC channels
      • +/- 1V, AC or DC -Coupled, 50 ohm, SMA inputs and outputs
    • LVDT-Servo -- Signal Conditioner & Embedded Servo Controller
      LVDT-Servo is a turnkey instrument combining Innovative's Cardsharp single board computer, FMC-Servo I/O module plus custom firmware and software to perform 4 channels of LVDT synchronous, simultaneous demodulation and control. The digital demodulation core provides sharp digital low-pass filtering and rapid phase tracking on the delta phase of the excitation and return signal. Built-in null point calibration efficiently solves the offset error around the null point. The powerful hardware platform supports a wide range of excitation frequencies from 400 Hz to 20 KHz, with latency of less than 2.7 ms. The Xilinx Zynq Z7045 FPGA is available for custom, real-time servo loop core implementations. Build the algorithm in VHDL, Xilinx System Generator and MATLAB, or Xilinx High Level Synthesizer (HLS) running inside the FPGA. Then, run a C++ program as the servo loop running in bare-metal in CPU core 1. (+)

      Features:

      365932970491140186.jpg
      • Xilinx Zynq Z7045 with dual ARM Cortex-A9 CPU, 1 GB RAM, running PetaLinux
      • Eight 16-bit ADC and eight 16-bit DAC sampling synchronously at 400 KHz, DC-coupled
      • USB 2.0 x1, 1 GbE x1, 32 GB eMMC, JTAG
    • Quixote Complete SDR Solution
      1 GHz TMS320C6416 DSP (+)

      Features:

      22229.jpg
      • 2 to 6 MGATE Virtex-II FPGA
      • 32 MB SDRAM, 8 MB ZBT SBSRAM
      • AD6645 and AD9764 converters
    • cToro
      150-MHz TMS320C6713 DSP (floating point) (+)

      Features:

      • 16 independent analog I/O channels to 250 Ksamples/sec
      • 64 bits digital I/O
      • CompactPCI 64/32-bit, 33-MHz, 5 V/3.3 V
    • PMC/XMC FPGA Cards
      Integrates ultra-fast signal capture, generation, and co-processing on an advanced PMC architecture (+)

      Features:

      31717.jpg
      • New generation analog devices
      • Large user-reconfigurable Virtex-II Pro FPGA
      • Ample DDR memory
    • X3-DIO
      64 single-end/32 differential digital I/O (+)

      Features:

      • 100 MHz signal rates to FPGA using LVDS
      • 50 MHz LVCMOS signal rates
      • 400 MB/s LVDS capture/playback to SRAM
    • eInstrument PC & eInstrument-DAQ Node & eInstrumentPC Atom
      eInstrument-PC is a miniature Windows/Linux embedded PC for standalone or distributed instrumentation using ultimate-performance XMC I/O modules (+)

      Features:

      45485.jpg
      • It runs all standard Windows/Linux software just like a desktop PC
      • Included is an Intel Penryn Core2 Duo 2 GHz or low-power Celeron
      • eInstrument-DAQ Node is a large variety of ultimate-performance XMC modules housed in a rugged enclosure featuring an ultra-fast Cabled-PCIe carrier position data acquisition near the unit under test without sacrifi cing high-speed connectivity to a host PC
  • L-3 Communications Telemetry -West  (1)
    • ADAS 5000
      VMEbus-based Data Acquisition System (+)

      Features:

      • Automates test and measurement activities for data acquisition applications
      • Provides signal conditioning, A/D conversion, data storage and data distribution
      • Memory in transducers provide transducer characteristics to system, allowing the universal signal conditioning amplifier to automatically self-configure to that transducer's requirements
  • Lyrtech  (1)
    • VSG-VSA solution
      Complete FPGA-based, multichannel A/D and D/A conversion solution for advanced vector signal generation (VSG) and vector signal analysis (VSA) (+)

      Features:

      45766.jpg
      • Minimum of eight 14-bit, 105-MSPS ADC channels
      • Minimum of eight 14-bit, 480-MSPS interpolated DAC channels
      • 2 GB memory module, allowing simultaneous recording/Playback
  • Nallatech  (2)
    • XMC-240
      FPGA processing and analog input PMC/XMC mezzanine (+)

      Features:

      42876.jpg
      • Designed to meet the signal processing needs of modern signal intelligence, software defined radio and radar applications
      • The XMC-240 is the latest product to be introduced to the highly successful Nallatech REVX Series of rugged embedded processing solutions
      • The XMC-240 features four channels of analog input that can sample analog signals at up to 250 MSPS with 14 bits resolution
    • VXS-620 FPGA
      FPGA and PowerPC VXS multiprocessor (+)

      Features:

      42875.jpg
      • Designed to meet the signal processing needs of modern signal intelligence, software defined radio, and radar applications
      • The VXS-620 is the latest product to be introduced to the highly successful Nallatech REVX Series of rugged embedded processing solutions
      • The VXS-620 features an onboard Xilinx Virtex-5 FPGA for the implementation of high performance DSP applications
  • Nuvoton Technology  (1)
    • WAU8812
      Mono audio Codec for VoIP-telephone, hands-free telephony markets; provides flexibility in performance and power consumption (+)

      Features:

      38376.jpg
      • Robust, high-fidelity, 24-bit signal architecture
      • 93dB Digital-to-Analog Converter (DAC), Signal to Noise Ratio (SNR), and 91dB Analog-to-Digital Converter (ADC) SNR at audio sampling rates from 8 KHz to 48 KHz
      • Industry-leading 6uA standby current, which greatly reduces power consumption and extends battery life in hand-held applications
  • Pentek, Inc.  (4)
    • Model 71624
      The Model 71624 dual channel, 34 signal, adaptive IF (Intermediate Frequency) relay XMC with a Virtex-6 FPGA. As an IF relay, it accepts two IF analog input channels, modifies up to 34 signals, and then delivers them to two analog IF outputs. Any signal within each IF band can be independently enabled or disabled, and changed in both frequency and amplitude as it passes through the module. The Model 71624 supports many useful functions including signal drop/add/replace, frequency shifting and hopping, amplitude equalization, and bandwidth consolidation. (+)

      Features:

      308688793538844775.jpg
      • Modifies 34 IF signals between input and output
      • Up to 80 MHz IF bandwidth
      • Two 200 MHz 16-bit A/Ds
    • RTR 2727
      the Model RTR 2727 rugged portable recorder suitable for military and aerospace applications. The system features recording and playback of IF signals up to 700 MHz with signal bandwidths to 200 MHz. It can be configured with 500 MHz 12-bit A/Ds or 400 MHz 14-bit A/Ds and an 800 MHz 16-bit D/A. Pentek’s SystemFlow software allows turnkey operation through a graphical user interface (GUI), while the SystemFlow application programming interface (API) allows easy integration of the recording software into custom applications. (+)

      Features:

      223484716525535130.jpg
      • Designed to operate under conditions of shock and vibration
      • Portable system measuring 16.9" W x 9.5" D x 13.4" H
      • Lightweight: approximately 30 pounds
    • 8111
      Modular Analog RF Slot Downconverter Series (+)

      Features:

      223484205525220211.jpg
      • Accepts RF signals from 800 MHz to 3.000 GHz in seven different models
      • Accepts RF input levels from -60 to -20 dBm
      • 225 MHz IF output with 80 MHz output bandwidth
    • SystemFlow Simulator for Talon Recording
      SystemFlow Simulator for Talon Recording Systems. (+)

      Features:

      238069482525561414.jpg
      • Provides real-time recording system simulation
      • Demonstrates SystemFlow signal & file viewer tools
      • Capable of simulating all Talon analog and digital recording systems
  • Radisys Corporation  (2)
    • FlowEngine
      A deep packet inspection (DPI) software framework to enable network equipment providers (NEPs) to accelerate development and delivery of applications that make use of DPI (+)

      Features:

      • Designed to save time and boost performance, FlowEngine combines best-in-class software components with Continuous Computing load balancing and Trillium monitoring software with an extensive range of application intelligence software from Qosmos and packet processing software from 6WIND and Wind River
      • Provides a foundation allowing users new to network intelligence to rapidly create advanced applications that run on the company's carrier-class, standards-based FlexTCA hardware platforms
      • Originally built on Continuous Computing's field-proven 10G FlexPacketATCA-PP50 DPI blade, FlowEngine is now coming to the 40GbE FlexTCA platforms delivering a range of solutions from 40-320Gbps capacity
    • PROCELERANT RMS420-5000XSL
      Server (+)

      Features:

      • Two Intel Quad-Core Xeon (Harpertown) processors at 2.33 GHz or 2.83 GHz with 12 MB of L2 cache and a front side bus (FSB) speed of 1333 MHz
      • Processors incorporate the latest Intel Core Architecture and are built with 45 nm process technology for maximum processing speed with reduced power consumption
      • Core architecture processors are particularly well suited for Single-Instruction, Multiple-Data (SIMD) parallel processing, which is commonly used for high-performance image and signal processing applications
  • Red Rapids  (3)
    • Red Rapids Model 277
      Available in XMC, CCXMC, PCIe formats (+)

      Features:

      338814828861414745.jpg
      • Dual or quad 16-bit (250 MHz) ADCs
      • AC or DC coupled analog inputs
      • Fixed or variable frequency synthesizer
    • Signal Stream
      A product family for general-purpose signal acquisition and generation for military applications such as Software-Defined Radio (SDR) and radar pulse receivers/transmitters as well as applications in the medical and industrial markets (+)

      Features:

      • Available in PCIe or XMC form factors, the devices integrate a set of software programmable features including selectable operating modes – continuous, snapshot, and periodic – time-stamped data samples, external or timed event triggers, data packing, and data sizing
      • Signal Stream devices, which come in seven different models, configure their data path as a receiver for ADC channels and a transmitter for DAC channels
      • Each type of channel may process raw sample data or data packets as defined by the VITA 49 specification
    • SigStream and SigFPGA Product Families
      The SigStream product family instantly transforms a general pur-pose computer into a high speed signal acquisition platform. (+)

      Features:

      347111134861436731.jpg
      • The hardware incorporates a rich set of software programmable features that include selectable operating modes (continuous, snapshot, periodic), external or timed event triggers, timestamped data samples, and flexible data formatting.
      • Each channel can stream raw samples or data packets defined by the VITA 49 specification.
      • The SigFPGA product family provides an ideal platform to rapidly field application specific signal acquisition and generation functions minus the expense of custom hardware development.
  • RF Engines Limited  (2)
    • SpectraView™ SV900
      RF Engines' SpectraView™ SV900 system is being developed to provide a complete and cost-effective solution for performing real-time spectral analysis of very wideband analog signals. The SV900 is based around the latest high performance digitisers and powerful signal processing hardware, and can be interfaced directly to a standard personal computer. The package includes Advanced Signal Display Software (ASDS), a full-featured PC application that provides the user interface to the analysis system, with a variety of mechanisms for displaying, analysing and storing both time and frequency domain data. (+)

      Features:

      • Cost-effective spectral analysis solution
      • Extremely wideband analysis capabilities
      • Minimal setup and configuration
    • DSP Cores for FPGA
      Signal processing cores are highly optimized FPGA designs for applications with high sample rates and demanding performance requirements (+)

      Features:

      • Guaranteed bit-true models provided with each core
      • Highly optimized implementations using pipelined architectures
      • Designs tailored to specific bit width and precision requirements
  • Robotrol Corporation  (3)
    • RPC632
      A high-speed analog input card (+)

      Features:

      14969.jpg
      • 32 single-ended or 16 differential analog inputs
      • Ranges: 25 mv to 10V (unipolar or bipolar)
      • 500 kHz A/D throughput rate; inputs protected to 32V
    • RPC628
      A high-speed analog I/O card (+)

      Features:

      15915.jpg
      • 16 single-ended or eight differential analog inputs; ranges: 25 mV to 10V (unipolar or bipolar)
      • Eight analog outputs; ranges: 2.5V, 5V, 10V, 5V, 10V, -5 to 0V, -10 to 0V
      • 250 kHz A/D throughput rate, inputs protected to 32V
    • RPC628 Analog I/O
      16 SE or 8 DI inputs (ranges: 25 mV to 10 V (unipolar or bipolar), 250 KHz throughput, inputs protected to ±32 V (+)

      Features:

      • Eight analog outputs (ranges: 2.5 V, 5 V, 10 V, ±5 V, ±10 V, -5 V to 0 V, -10 V to 0 V)
      • 16 digital I/O, bit-by-bit programmable as inputs or outputs
      • Options: 4 mA to 20 mA current loops for both inputs and outputs, auto scan mode (scan all inputs with one command)
  • Shenzhen WAYJUN Industrial Automation  (2)
    • 8 Channels Analog Signal To RS485
      8-channel Analogue Signal to rs485/232 Signal Output A-D Converter with Modbus,Data Acquisition Samples: Part No.:WJ28-A4-485 means 8 channels 4-20mA input,ouput is RS485 interface Part No.:WJ28-U1-232 means 8 channels 0-5V input,output is RS232 interface Part No.:WJ28-U2-485 means 8 channels 0-10V input,output is RS485 interface (+)

      Features:

      • Eight analog signal acquisition, isolated converter RS-485/232 output
      • 24-bit AD converter, accuracy>0.05%
      • Signal input / output:3000VDC isolation
    • 4-20ma to RS485 Converter with Modbus
      Featuresï?? â—? Analog signal acquisition,isolated RS-485/232 output â—? 12-bit AD converter,testing accuracy>0.1% â—? Can be remotely reconfigured for modules Analog Current signal to RS485 or RS232 Converter,Slim-line plastic housing with integral 35mm DIN rail mounting , LED indication and terminals,power supply(8-32VDC) [...] (+)

      Features:

      325368931670794760.jpg
  • Signatec, Inc.  (6)
    • SIG-PRG
      Portable high-speed data acquisition and waveform generation systems: 2 analog A/D channels at up to 160 MHz sampling rate, 2 analog I&Q D/A channels, bandwidth 100 KHz to 600 MHz (+)

      Features:

      42051.jpg
      • Two analog signal recording channels at up to 160 MHz sampling rate
      • Two analog I&Q waveform generation channels at up to 1 GHz sampling rate
      • 16-bit resolution for both the A/D and D/A channels
    • PDAC4000
      4000 MSps arbitrary signal waveform generator playback PCI board featuring four onboard AD9779 DACs (+)

      Features:

      32486.jpg
      • Four 16-bit DAC outputs at 1000 MSps
      • 512 MB DDR RAM
      • Modular plug-in for PMP1000 baseboard
    • PX1500-2
      The PX1500-2 is a 2-channel high-speed digitize that can acquire up to 1.5 giga-samples per second (GSPS) on each channel or up to 3 GSPS for single channel operation (+)

      Features:

      46569.jpg
      • 2 Analog Channels at up to 1.5 GHz Sample Rate per Channel
      • 1 Analog Channel at up to 3.0 GHz Sample Rate in Interleaved Mode
      • Bandwidth Up to 2 GHz
    • PX1500-4
      Signatec's PX1500-4 captures four synchronized channels at sampling rates up to 1.5 GHz, or two synchronized channels up to 3 GHz when interleaving the ADC data (+)

      Features:

      43923.jpg
      • 4 analog channels at up to 1500 MHz sample rate per channel
      • 2 analog channels at up to 3000 MHz sample rate per channel in interleaved mode
      • Bandwidth up to 2 GHz
    • PDA16
      Dual-channel, 160 MHz digitizer delivers 16-bit resolution (+)

      Features:

      • Enabled by Xilinx Virtex FPGAs
      • Optimized for embedded processing and serial connectivity
      • Two analog channels at up to 160 MHz Sample rate per channel
    • PX14400
      High-Speed PCI Express Digitizer Capable of Sustained Recordings Over 1.2 GB/s with Xilinx Virtex-5 FPGAs for Embedded Real-Time Processing (+)

      Features:

      43039.jpg
      • 400 MHz sampling rate per channel
      • 2 analog channels
      • 14-bit A/D resolution
  • Soft DB  (1)
    • Signal Ranger Mk3 Standard and Pro
      Signal Ranger Mk3 is a DSP board featuring a TMS320C6424 DSP running at 590 MHz and a XC3S400 FPGA (Signal Ranger Mk3 Pro. version only) (+)

      Features:

      46483.jpg
      • This DSP board provides 6 analog I/Os (96 kHz/24-bit)
      • It has been designed for pro-audio and high-performance control applications
      • Communication interfaces include a high-bandwidth USB 2 interface as well as an Ethernet communication interface that allows the remote control of the DSP board over the web (an IP Stack DSP firmware is included)
  • Spectrum Signal Processing  (3)
    • TMI-3350 4-Channel Wideband Analog I/O
      Hot swappable (+)

      Features:

      22244.jpg
      • External frequency reference input for accurate sampling frequency control and time-stamping
      • IRIG-B time code input for time stamping
      • Synchronization connector allows up to three TM1-3350 and DDCs/DUCs running on PRO-3100 boards to receive a common synchronization signal
    • Smart Antenna Development Platform
      A Smart Antenna Development Platform that leverages upon the reconfigurability, flexibility, and modularity of Spectrum's flexComm solutions (+)

      Features:

      • Targeted at government and commercial users that require increased capacity, extended range, and signal enhancement to get the most out of their infrastructure investment.
      • Supports two to eight receive channels with a 10 MHz bandwidth and can scan the frequency range from 20 MHz to 3 GHz, sufficient for all military communications and cellular bands
      • Provides a direction finding example program that can determine the relative position of an incoming narrowband signal
    • PMC-2MAI Dual A/D Converter PMC Module
      Two 12-bit 65 MSPS A/D converters (+)

      Features:

      • Digital step attenuator allowing input levels from -9 to +6 dBm
      • Digital signal level monitor
      • External input/output clock source
  • Strategic Test  (6)
    • UF2e-6110
      Two-channel 125 MS/s 8-bit Arbitrary Waveform Generator (AWG) PCI Express card (+)

      Features:

      35350.jpg
      • Synchronous multichannel capability
      • Well suited for creating complex waveforms in applications that include I&Q signal generation, RADAR system development, communications testing, laser positioning, and HDTV signal generation
      • Each channel has its own 8-bit Digital-to-Analog Converter (DAC) to ensure synchronous output and a choice of three reconstruction filters (5th and 4th order Butterworth lowpass) giving bandwidths of 25 MHz, 5 MHz, or 500 kHz
    • UF6031
      A high-speed arbitrary waveform generator (ARB/AWG) in PCI form factor (+)

      Features:

      • Uses 14-bit D/A converters and is able to generate complex analog signals at rates of 125 MSps on both channels
      • 512 MB of onboard signal memory
      • 3 dB bandwidth of 60 MHz (no filter), signal-to-noise ratio of more than 72 dB, and crosstalk of less than –80 dB
    • UF2e-4731 and UF2e-4730
      16-channel 500 kSps 16-bit data acquisition cards for PCI Express (+)

      Features:

      • The UF2e-4731 has 16 analog inputs and the UF2e-4730 has 8 inputs
      • Unique features include the options for dual-timebase sampling, synchronous digital inputs, asynchronous digital I/O, and the ability to synchronize hundreds of channels
      • Drivers and programming examples for Microsoft Windows Vista, XP64, XP, and Linux (RedHat, Fedora, SuSe, and Sarge) are supplied with the card, as well as the SBench 5.3 oscilloscope program
    • UF2e-4640
      PCI Express Waveform Digitizer/Oscilloscope boards (+)

      Features:

      33996.jpg
      • PCI Express x1 boards
      • 3 MSps 16 bit ADCs
      • One, two, or four simultaneous analog input channels with eight input ranges per channel: ±50 mV up to ±10 V
    • UltraFast UF3132
      An 8-channel PCI digitizer card (+)

      Features:

      • Eight high-speed A/D channels; up to 16 cards can be synchronized to create a 128-channel system
      • 12-bit A/D converters with maximum sampling rates of 25 MSps
      • Provides true simultaneous sampling and has up to 256-MSample onboard signal memory
    • UF2-6000 AWG Cards
      The UF2-6000 range includes eight 14-Bit resolution Arbitrary Waveform Generator cards (+)

      Features:

      • Available with 1, 2, or 4 analog outputs, maximum output rates of 125 MSps, 60 MSps, or 20 MSps and up to 4 GigaSamples of memory depth
      • For military applications, the Multiple Replay option is a popular choice as it allows the generation of radar signals with Pulse Repetition Frequencies of up to 10 MHz, while the Digital Outputs option adds 2, 4, or 8 digital outputs synchronized to the analog outputs – often used to synchronize external equipment
      • If the signal outputs need to be controlled by an external TTL gate signal, then the Gated Sampling option can be used
  • Technobox, Inc.  (1)
    • 2677
      A 2-channel, 12-bit, 10 Msamples/sec, A/D converter with antialiasing filter (+)

      Features:

      • Single-wide PMC card form factor
      • Two bipolar, single-ended analog inputs are passed through analog filters to provide initial band limiting
      • Signals are sampled at 20 Msamples/sec and the digital output of each A/D converter is passed through a decimation by 2 function which effectively reduces the sample rate to 10 Msamples/sec
  • TEK Microsystems, Inc.  (1)
    • Calypso-V6
      The new Calypso-V6 supports either two 12-bit analog-to-digital converter (ADC) channels at 3.6 GSPS (Gigasamples per second) or six channels at 1.8 GSPS. Like all members of the QuiXilica-V6 VME / VXS family, the Calypso-V6 is compatible with legacy VME systems as well as newer ANSI/VITA 41 VXS based systems and combines the highest density FPGA processing available in any 6U form factor with the ultimate in ultra wide band ADC signal acquisition. (+)

      Features:

      186593658209512272.jpg
      • Two 12-bit ADCs at 3.6 GSPS, Also supports 6 channels @ 1.8 GSPS
      • Three Xilinx Virtex®-6 FPGAs
      • Sample-accurate trigger input
  • Tektronix, Inc  (1)
    • MSO70000
      MSO70000 Series combine industry-leading bandwidth of 20 GHz with the industry's highest waveform capture rate, best signal fidelity, and lowest noise floor (+)

      Features:

      43310.jpg
      • Discover Problems in Seconds – With 4 channel analog bandwidth ranging from 4 to 20 GHz depending on model, the MSO70000 offers up to 5 times more bandwidth and 5 times better timing resolution than the fastest integrated MSOs currently available – enabling greater signal visibility for problem discovery
      • It provides record lengths up to 250 million points and sample rates of 50 GS/s analog and 12.5 GS/s digital
      • This uncompromised performance means that engineers can capture long duration events with high sample resolution and have time-correlated views of high-speed analog and digital data
  • TEWS Technologies LLC  (6)
    • TAMC 900
      The TAMC900 is an analog to digital converter AdvancedMC with 8 high speed ADCs providing preprocessing power by a Virtex-5 FPGA and high-speed onboard memory (+)

      Features:

      38072.jpg
      • Single-width / mid-height AMC.1 Type 8 compliant module, x8 PCIe port; IPMI interface
      • Virtex-5 LXT FPGA; 4 MB QDR-II SRAM
      • Analog-to-Digital Converter: 8 x LTC 2254 ADCs, 105 MSps, 14 bit
    • TAMC900
      High performance analog to digital converter AdvancedMC (+)

      Features:

      • Virtex-5 FPGA and high-speed onboard memory
      • Single-width, mid-height PICMG AMC.1 module; x8 PCI port (AMC.1 Type 8 compliant)
      • Virtex-5 LXT FPGA; 4 MB QDR-II SRAM
    • TIP102/102-TM
      An IndustryPack compatible motion controller using incremental encoder (+)

      Features:

      18090.jpg
      • Interface according to IndustryPack specification
      • Identification-PROM supports auto-configuration
      • Single size IndustryPack
    • TIP111/111-TM
      An IndustryPack compatible motion controller using absolute Encoder (+)

      Features:

      • Interface according to IndustryPack specification
      • Identification-PROM supports auto-configuration
      • Single size IndustryPack
    • TIP710
      An IndustryPack compatible module (+)

      Features:

      • Identification-PROM supports auto-configuration
      • Single size IndustryPack
      • 16 digital outputs, high side switches
    • TIP670
      A single-size IndustryPack interface (+)

      Features:

      10972.jpg
      • Identification-PROM supports auto configuration
      • 8 interrupt generating digital inputs
      • 24V signal voltage for inputs
  • Texas Instruments  (1)
    • 12-bit ADS7924
      12-bit ADS7924 successive approximation (SAR) analog-to-digital converter (ADC) (+)

      Features:

      • Through intelligent system power management features, the 2.2-V ADS7924 works with any low-power system requiring sensor monitoring to potentially lower power across the system by more than 50 percent
      • Once programmed through its I2C interface, the device can operate independently, periodically waking itself to scan all four ADC channels while using only 5 uW
      • This frees the MCU to process other activities or power down entirely to yield significant power savings in energy harvesting, medical, communications, remote sensor signal monitoring, and portable applications
  • VadaTech Inc.  (1)
    • Signal Processing Solutions
      VadaTech provides Signal Processing Solutions that redefine performance density with superior SWaP-C. From RADAR data acquisition & signal processing, FPGA/data processing, video/image processing, & more, VadaTech has a solution for you. Our standard modular building blocks include high-performance multi-core Intel, Tilera, and Freescale processors; Altera, Xilinx, and TI FPGAs; ATI & other graphics processors; & powerful ADCs and DACs. (+)

      Features:

      308688375538687283.jpg
      • Modular Open Standard Architectures (MOSA)
      • Approx 1/2 the SWaP-C of competing products
      • Rugged 1U Signal Processing platforms with time stamping options
  • ZTEC Instruments, Inc.  (15 of 18)
    • ZT500PXI
      14-Bit Arbitrary Waveform Generator (+)

      Features:

      • 2 mVpp to 7 Vpp Programmable Output Signal Range in 2 mV Steps
      • 300 MSample/s to 40 MSample/s Programmable Sample Rate
      • 200 MHz Maximum Analog Bandwidth
    • ZT400VXI
      A high-speed digitizer (+)

      Features:

      • DC to 150 MHz analog input bandwidth
      • ± 1V analog input signal range
      • X1, X2, X4, and X5 selectable analog input gain
    • ZT400VXI
      A high-speed digitizer (+)

      Features:

      9289.jpg
      • DC to 150 MHz analog input bandwidth
      • ± 1V analog input signal range
      • X1, X2, X4, and X5 selectable analog input gain
    • ZT4610 Family
      Family of digital storage oscilloscopes (+)

      Features:

      31667.jpg
      • Available in PCI, CompactPCI/PXI, and VXI
      • 4 GS/s real-time sampling rate with 800 MHz analog bandwidth
      • For higher acquisition rates, either equivalent-time (multi-capture reconstruction) or interpolated-time (single-capture reconstruction) mode can be used to achieve up to 200 GS/s
    • ZTC400SCU
      Analog input: DC to 150 MHz bandwidth (+)

      Features:

      • Analog signal range: 1V maximum
      • 500 MSamples/sec sample rate
      • 12-bit ADC resolution
    • ZT530PXI
      A dual-channel, 160 Msamples/sec data, 400 Msamples/sec DAC, 16-bit arbitrary waveform generator (+)

      Features:

      17198.jpg
      • Single-wide, 3U PXI/CompactPCI card
      • 32-bit digital TTL outputs provide time markers, sync, or pattern outputs
      • Up to 1 Msample/channel memory
    • ZT450PXI-00 -Digital-Storage Oscilloscope
      2 (PCI, PXI) or 4 (VXI) channels (+)

      Features:

      • 8-bit resolution
      • 1 GSps to 2.5 GSps single-channel interleaved sample rates
      • 500 MHz to 1 GHz max analog bandwidth
    • ZT621VXI
      Two channels simultaneous full speed (+)

      Features:

      • 1 Gsample/sec single shot
      • signal processing, range offset, coupling, impedance, sampling rate, and analog filtering
      • 300MHz analog bandwidth
    • ZT432VXI
      2 channel (PXI) or 4 channels simultaneous (VXI), 12-bit resolution (+)

      Features:

      • 200 MS/s, 90 MHz analog bandwidth
      • Up to 4 MS record length per channel
      • Programmable range, offset, coupling, impedance, sampling rate, and analog filtering
    • ZT442 family
      A family of three complete, high performance digital storage oscilloscopes (+)

      Features:

      14829.jpg
      • Two channels simultaneous full-speed
      • 1 GSample/sec single shot
      • Flexible signal processing, range, offset, coupling, impedance, sampling rate, and analog filtering
    • Z1428VXI
      A full featured digital storage oscilloscope for both legacy and next generation modular instrumentation systems (+)

      Features:

      16009.jpg
      • 2 channels simultaneous, 8-bit resolution
      • 1 GSps, 250 MHz analog bandwidth
      • 1 MS record length per channel
    • ZT442PXI
      2 Channels Simultaneous Acquisition (+)

      Features:

      • 1 GSample/s Single Shot
      • Flexible Range, Offset, Coupling, Impedance, Sampling Rate, & Analog Filtering
      • 300 MHz Analog Bandwidth
    • ZT450
      Series of high-speed, low-power modular Digital Storage Oscilloscopes (DSO) for PCI, CompactPCI/PXI, and VXI (+)

      Features:

      21165.jpg
      • Built on data conversion technology with deep waveform memory
      • DSO performance in a modular instrumentation form factor
      • Extensive benchtop DSO capabilities
    • ZT200VME
      A modular intermediate frequency (IF) processor providing IF signal detection, processing, and modulation in a 6U VMEbus instrument (+)

      Features:

      • TMS320C50 DSP provides a complete set of IF measurement and processing capabilities including magnitude/phase measurements, In-phase/Quadrature (IQ) measurements, modulation analysis, signal modulation and demodulation, error detection and correction, equalization and filtering, feedback control, and adaptive beam-forming and noise cancellation
      • Three IF inputs (100- kHz to 10 MHz adjustable frequency range)
      • 80 dB input signal dynamic range
    • ZT410 Family
      A family of digital storage oscilloscopes for PXI, PCI, CompactPCI, and VXI form factors (+)

      Features:

      25180.jpg
      • Available in both 14- and 16-bit versions
      • Two or four channels
      • 500 MSps (zt410-20) or 400 MSps (zt410-50) interleaved sample rates
05/22/22 01:11
Close

Subscribe to Analog updates