Analog

Showing results for: d/a
Refine Analog companies and products:
analog analogue analog circuit analog ic analogue circuit analogue ic analog to digital digital to analog a/d d/a adc dac continuous signal
Click on any vendor
to see a listing of
d/a related products.
  • GE Intelligent Platforms, Inc.  (15 of 17)
    • Tsunami PC104
      A Field Programmable Gate Array (FPGA) processor for PC/104-Plus systems (+)

      Features:

      17251.jpg
      • Integrates with the Wave FPGA software tool kit from SBS for easy application development
      • Suitable for mobile cart-based systems, machine sensor, and control I/O applications
      • Altera Stratix FPGAs on a 32-bit/33-MHz PCI interface with memory and high-bandwidth data paths
    • Tsumani 6U CPCI Development Kit
      FPGA processor solution targeted at high performance software defined radio applications (+)

      Features:

      • Dual Stratix EP1S80 FPGAs are tightly coupled to provide a power platform for signal processing
      • Two PMC module sites provide I/O connectivity to either front panel or back panel connections
      • A direct high bandwidth 1 GBps path from the PMC P4 connector directly to the FPGAs
    • CompactPCI FPGA Processor
      Two Stratix EPS180 FPGAs (+)

      Features:

      19198.jpg
      • Two PMC sites with 1-GBps high-speed data paths to each FPGA
      • 8-GBps connection between FPGAs for a common processor fabric
      • Local bridges route 64-bit/66-Mhz CompactPCI backplane to PMC and FPGA local buses
    • 6U CPCI FPGA Processor
      Two Stratix™ EPS180 FPGAs (+)

      Features:

      19051.jpg
      • Two PMC sites with 1 GB high-speed data paths to each FPGA
      • 8-GB connection between FPGAs for a common processor fabric
      • Local bridges route 64-bit/66-MHz CompactPCI backplane to PMC and FPGA local buses
    • PCI-based FPGA processor
      Tsunami A40 delivers many times the processing of CPU or DSP boards (+)

      Features:

      19197.jpg
      • Altera EP1S40 FPGA on the PCI and expansion module(s)
      • 4 MB SRAM and 1 GB SDRAM on the A40 PCI base board
      • 8 MB SRAM and 384 MB SDRAM on A40 FPGA expansion modules
    • TS-CPCI-8002
      Dual EP1S80-C5 FPGA (+)

      Features:

      • Two 64/66 MHz PMC sites
      • Two 64 MB SDRAM
      • 2 MB SRAM
    • TS-CPCI-8001
      High-performance, FPGA-based computing platform for demanding signal and image processing applications (+)

      Features:

      21058.jpg
      • Suitable for SDR, sonar, and other high-performance signal processing applications
      • Dual Stratix EP1S80 FPGAs onboard
      • Two PMC sites with 1 GBps high-speed data paths to each FPGA
    • Xilinx FPGA Blade
      PCI Software Radio Xilinx FPGA blade (+)

      Features:

      33584.jpg
      • GE Intelligent Platforms radio PMC products integrated with Virtex-II based FPGA PMC module to supplement the onboard FPGA
      • Single-slot solution
      • Large onboard memory
    • TS-104-3001
      PCI/104 format for cost effective solutions (+)

      Features:

      • Tsunami Development Kit gets you up and running on an FPGA Computing platform in less than an hour
      • Wave FPGA Tool Kit provides API, drivers, source code, and more
      • 32 bit/ 33 MHz PCI bus provides maximum bandwidth to host resources [...]
    • ICS-572
      2-channel ADC, 2-channel DAC with Xilinx FPGA SDRAM, QDR SRAM, and PCI 64/66 interface (+)

      Features:

      33579.jpg
      • 2-channel Software Radio
      • Receive and transmit on a single PMC
      • Sample rates: ADC 105 MHz, DAC 200 MHz
    • ICS-1556
      4-channel, 400 MHz 14-bit ADC PMC module with Virtex-5 SX95T user programmable FPGA (+)

      Features:

      • 4 transformer-coupled analog inputs
      • Analog-to-digital resolution 14-bits
      • Fs≤ 400 MHz per channel
    • TS-DK-IT01
      An imaging development kit aimed at leveraging FPGA processing capabilities for high-performance imaging applications (+)

      Features:

      • Includes the SBS Tsunami FPGA platform, infrastructure software, development environment, and multiple resources for integration of CameraLink and other custom image processing applications [...]
    • PIO-PMC1
      PMC conduction cooled (+)

      Features:

      21192.jpg
      • User programmable Altera FPGA
      • PMC interface to PCI mezzanine conforms to the requirements of IEEE-1386.1-2002
      • Multiple I/O functions (analog, serial, discrete) all on the same PCI mezzanine card
    • ICS-1554
      4-channel, 160 MHz 16-bit ADC PMC module with Virtex-5 SX95 user programmable FPGA (+)

      Features:

      • Four AC-coupled analog inputs
      • FS < 160 MHz per channel
      • Xilinx Virtex-5 SX95 User Programmable FPGA
    • ICS-8550
      Rugged XMC Module provides 210 MHz ADCs and Virtex-4 Processing Power (+)

      Features:

      33568.jpg
      • 2 ADC channels (Analog Devices AD9430): 12 bits @ 210 MHz
      • Xilinx Virtex-4 FX60 or FX100 FPGA with two IP cores (default logic core, programmable DDC core)
      • Hardware Development Kit (HDK) included
  • Traquair Data Systems, Inc.  (7)
    • ORS-11x
      Multi-channel analog interfaces with a user-programmable Spartan-IIE or Virtex-II FPGA, providing developers with the means to implement FPGA-based digital signal processing solutions (+)

      Features:

      31753.jpg
      • Can be used as stand-alone devices with the user-programmable FPGA responsible for supporting all signal processing functionality, or as daughtercards to micro-line DSP/FPGA boards
      • A variety of multi-channel A/D/A configurations are supported: 2-channel 14-bit A/D/A with ADC sample rates up to 65 MSps; 4-channel 16-bit A/D/A with ADC sample rates up to 2.5 MSps; 12-channel A/D/A with ADC sample rates up to 250 KSps
      • If the capabilities of a Texas Instruments TMS320C6000 DSP processor are required, an ORS-11x board can be fitted as a daughtercard to a TMS320C6000-based micro-line embedded DSP/FPGA board
    • micro-line ORS-1xx
      micro-line compatible analog I/O & FPGA boards (+)

      Features:

      19216.jpg
      • Multichannel 12/14/16-bit A/D/A capabilities
      • User programmable Spartan-IIE or Virtex-II FPGA
      • Used as peripheral to DSP or as standalone device
    • ultra-compact
      The ultra-compact UC1394a-1 and UC1394a-3 multi-chip modules provide Texas Instruments TMS320C5000 DSP, Spartan-II or Spartan-3 FPGA, and ready-to-use IEEE1394a FireWire communication capabilities in tiny 30 mm x 36 mm surface-mount PLCC packages (+)

      Features:

      31752.jpg
      • They are suitable as user-programmable DSP/FPGA resources or as FireWire connectivity devices
      • The UC1394a-1 incorporates a TMS320C5509 integer DSP, a 50 kGate Spartan-II FPGA, 8 MB of SDRAM
      • In addition to the I/O capabilities of the UC1394a-3, the UC1394a-1 provides external access to USB and four A/D inputs provided by the TMS320C5509 DSP processor
    • micro-line C6713CPU
      High-quality, single-board solution for applications requiring an embedded DSP and optionally programmable FPGA (+)

      Features:

      • Texas Instruments TMS320C6713 DSP
      • 64 MB of SDRAM (128 MB SDRAM available on request), 2 MB flash ROM
      • Optionally programmable Spartan-3 FPGA (up to 1 M gate density)
    • micro-line C6713 Compact
      Standalone and embeddable DSP/FPGA board (+)

      Features:

      • Texas Instruments TMS320C6713 floating point DSP
      • 250 k, 500 k, or 1 M-gate complexity Virtex-II FPGA
      • 400 Mbps IEEE 1394a FireWire interface
    • Micro-line C6713Compact
      Standalone and embedded-capable DSP/FPGA board (+)

      Features:

      19182.jpg
      • Texas Instruments TMS320C6713 floating point DSP Processor
      • 250k, 500, or 1M-gate complexity Virtex-II FPGA
      • 400 MBps IEEE 1394 FireWire interface
    • C6317Compact
      A DSP board with onboard FPGA (+)

      Features:

      • Texas Instruments TMS320C6713 floating-point DSP processor at 225 MHz (up to 1800 MIPS or 1350 MFLOPS)
      • Virtex-II FPGA (250k, 500k, or 1M gates)
      • Dual 400 Mbits/sec IEEE 1394 FireWire ports
  • Pentek, Inc.  (15 of 68)
    • Model 5973-324 for 3U VPX Model 7070-324
      FlexorSet Model 5973-324 for 3U VPX and Model 7070-324 for PCIe. They consist of the new Flexor Model 3324 4-Channel A/D & 4-Channel D/A FMC installed on either of two carriers. The carriers contain optimized Pentek FPGA intellectual property (IP) for A/D acquisition and D/A waveform playback, which is ideally matched to the four 500 MHz, 16-bit A/Ds and the four 1.5 GHz, 16-bit D/As with digital up-converters (DUCs) on the FMC. A rich set of software development tools enables rapid application development and rapid time to market. (+)

      Features:

      324106377621429115.jpg
      • Supports Xilinx Virtex-7 VXT FPGAs
      • GateXpress supports dynamic FPGA reconfiguration across PCIe
      • Four 500 MHz 16-bit A/Ds
    • Model 7158
      Dual 500 MHz A/D, 800 MHz D/A, Virtex-5 FPGAs - PMC/XMC module (+)

      Features:

      42940.jpg
      • The module includes two A/D and two D/A converters, two Virtex-5 FPGAs and two banks of DDR2 SDRAM
      • Complete software radio interface solution
      • Two 500 MHz, 12-bit A/D, one digital upconverter,Two 800 MHz, 16-bit D/As
    • 71851
      Jade family of data converter XMC modules. The Model 71851 is based on the Xilinx Kintex Ultrascale FPGA and features two 500 MHz, 12-bit A/Ds with multiband digital down converters (DDCs), one digital upconverter (DUC) and two 800 MHz 16-bit D/As. The Model 71851 offers a well-matched 200 MHz bandwidth on both the receive-side and on the transmit-side, which provides the complimentary solution necessary in many high-speed data acquisition, waveform generation, communications, satcom, UAV and radar applications (+)

      Features:

      3697998766215604825.jpg
      • The front end accepts two analog HF or IF inputs on front panel SSMC connectors with transformer-coupling into two Texas Instruments ADS5463 500 MHz, 12-bit A/D converters
      • A TI DAC5688 DUC (digital upconverter) and D/A accepts a baseband real or complex data stream from the FPGA and provides that input to the upconvert, interpolate and dual D/A stages
      • A/D Acquisition IP Modules: The Model 71851 features two A/D Acquisition IP modules for easily capturing and moving data. Each module can receive data from any of the two A/Ds or a test signal generator
    • Model 52621
      3-Ch 200 MHz A/D w/ DDC & 2-Ch 800 MHz D/A w/ DUC, Virtex-6 FPGA - 3U VPX (+)

      Features:

      239710912284470.jpg
      • Complete radar and software radio interface solution
      • Supports Xilinx Virtex-6 LXT and SXT FPGAs
      • Three 200 MHz 16-bit A/Ds
    • Cobalt 71630
      1 GHz A/D and D/A, Virtex-6 FPGA - XMC (+)

      Features:

      • Complete radar and software radio interface solution
      • Supports Xilinx Virtex-6 LXT and SXT FPGAs
      • One 1 GHz 12-bit A/D
    • Cobalt 53630
      1 GHz A/D, 1 GHz D/A and Virtex-6 FPGA - 3U OpenVPX Cobalt Board (+)

      Features:

      • Complete radar and software radio interface solution
      • Supports Xilinx Virtex-6LXT and SXT FPGAs
      • Supports gigabit serial fabrics including PCI Express, Serial RapidIO and Xilinx Aurora
    • Cobalt 78630
      1 GHz A/D, 1 GHz D/A and Virtex-6 FPGA - PCI Express Cobalt Board (+)

      Features:

      46541.jpg
      • Complete radar and software radio interface solution
      • Supports Xilinx Virtex-6LXT and SXT FPGAs
      • Includes 1 GHz 12-bit A/D and 1 GHz 16-bit D/A
    • 71620
      3 Channel 200 MHz A/D & 2 Channel 800 MHz D/A with Virtex-6 FPGA - XMC (+)

      Features:

      43866.jpg
      • Complete software radio interface solution
      • Supports Xilinx Virtex-6 LXT and SXT FPGAs
      • Three 200 MHz 16-bit A/Ds
    • 78621
      3-Channel 200 MHz A/D with DDC, DUC with 2-Channel (+)

      Features:

      • Model 78621 800 MHz D/A and a Virtex-6 FPGA - x8 PCIe
      • Complete radar and software radio interface solution
      • Supports Xilinx Virtex-6 LXT and SXT FPGAs
    • Onyx Model 71720
      Model 71720 3-Channel 200 MHz A/D and 2-Channel 800 MHz D/A with Virtex-7 FPGA - XMC (+)

      Features:

      223485199525664546.jpg
      • Supports GateXpress FPGA-PCIe Configuration Manager
      • Complete radar and software radio interface solution
      • Supports Xilinx Virtex-7 VXT FPGAs
    • Cobalt 78630
      1 GHz A/D and D/A Virtex-6 FPGA - x8 PCIe (+)

      Features:

      • Complete radar and software radio interface solution
      • Supports Xilinx Virtex-6 LXT and SXT FPGAs
      • One 1 GHz 12-bit A/D
    • Model 53741
      Model 53741 is a member of the Onyx® family of high-performance 3U VPX boards based on the Xilinx Virtex-7 FPGA. A high-speed data converter with a programmable digital down converter, it is suitable for connection to HF or IF ports of a communications or radar system. Its built-in data capture features offer an ideal turnkey solution. It includes a 3.6 GHz, 12-bit A/D converter and four banks of memory. In addition to supporting PCI Express Gen. 3 as a native interface, Model 53741 includes an optional connection to the Virtex-7 FPGA for custom I/O. Extendable IP Design: For applications that require specialized functions, users can install their own custom IP for data processing. Pentek GateFlow FPGA Design Kits include all of the factory installed modules as documented source code. Developers can integrate their own IP with the Pentek factory-installed functions or use the GateFlow Design Kit to completely FEATURES: Ideal radar and software radio interface solution � Supports Xilinx Virtex-7 VXT FPGAs � GateXpress supports dynamic FPGA reconfiguration across PCIe � One-channel mode with 3.6 GHz, 12-bit A/D � Two-channel mode with 1.8 GHz, 12-bit A/Ds � Programmable one- or twochannel DDC (Digital Downconverter) � 4 GB of DDR3 SDRAM � µSync clock/sync bus for multiboard synchronization � PCI Express (Gen. 1, 2 & 3) interface up to x8 � Optional user-configurable gigabit serial interface � Optional LVDS connections to the Virtex-7 FPGA for custom I/O � Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPXTM System Specification) [...] (+)

      Features:

    • 71861
      Model 71861 is a member of the JadeTM family of high-performance XMC modules. The Jade architecture embodies a new streamlined approach to FPGA-based boards, simplifying the design to reduce power and cost, while still providing some of the highest-performance FPGA resources available today. Designed to work with Pentek’s new NavigatorTM Design Suite of tools, the combination of Jade and Navigator offers users an efficient path to developing and deploying FPGA-based data acquisition and processing. (+)

      Features:

      350844755569383844.jpg
      • Complete radar and software radio interface solution
      • Supports Xilinx Kintex UltraScale FPGAs
      • Four 200 MHz 16-bit A/Ds
    • 7342
      Multichannel transceiver 3U CompactPCI board with FPGA (+)

      Features:

      32558.jpg
      • Four 125 MHz 14-bit A/Ds
      • Optional factory installed IP Core DDC
      • One digital upconverter with 500 MHz 16-bit D/A
    • 7642
      Multichannel transceiver PCI board with FPGA (+)

      Features:

      32562.jpg
      • Four 125 MHz 14-bit A/Ds
      • Optional factory installed IP core DDC
      • One digital upconverter with 500 MHz 16-bit D/A
  • National Semiconductor  (2)
    • NSC Ref Designs
      Six new reference designs from National Semiconductor Corp. enable products that consume less power, extend battery life and generate less heat (+)

      Features:

      • PowerWise reference designs combine energy-efficient devices and arrange them in a system to actively lower power consumption and reduce heat dissipation
      • Each proven PowerWise reference file kit includes applicable design schematic, bill of materials (BOM), board layout, firmware, design documentation and field-programmable gate array (FPGA) source code in synthesizable Verilog or VHDL
      • The designs address a wide range of applications including portable, lighting, solar, industrial, medical, communications infrastructure, and test and measurement. For more information on these reference designs, visit www.national.com/refdesign
    • FPGA Power Designer
      Helps designers create complete FPGA power supply designs in minutes (+)

      Features:

      46683.jpg
      • Models and optimizes power supplies for FPGAs quickly
      • Includes detailed supply requirements of more than 130 of the newest FPGA devices from Altera, Xilinx and others
      • Incorporates comprehensive power requirements published by each FPGA manufacturers
  • Pico Computing  (5)
    • E-14 EP 20/40/60
      A field deployable development platform utilizing the Xilinix Virtex-4 FPGA in a CardBus form factor (+)

      Features:

      • Complete CardBus interface capable of bus speeds up to 1 Gbps
      • Complete development platform can be deployed in the developer's end application
      • Xilinix Virtex-4 FX series FPGAs
    • M-503
      A modular FPGA board enabling high-performance, memory intensive hardware-accelerated computing (+)

      Features:

      • Addresses the ever increasing demands for memory and I/O bandwidth for HPC applications in the bioinformatics, image processing and signal processing domains
      • Features a Xilinx Virtex-6 LX240T FPGA with 2 independent banks of DDR3 SODIMM providing 17GB/s of local memory bandwidth to the FPGA
      • In addition to the DDR3, there are 3 independent banks of QDRII SRAM capable of 10.8GB/s of sustained random access memory bandwidth
    • E-17 FPGA Card
      The E-17 card is a small form factor FPGA platform based on a Xilinx Virtex-5 FPGA device (+)

      Features:

      43593.jpg
      • The card is compatible with standard ExpressCard (PCI Express) interfaces
      • Virtex-5 FX70T / LX50T / SX50T FPGA
      • 256 MB DDR2
    • EX-500 FPGA Board
      The EX-500 is a scalable cluster supporting up to six FPGA modules on a single PCI Express board (+)

      Features:

      43591.jpg
      • Applications include cryptography, bioinformatics, and accelerated computing
      • Up to six Xilinx Virtex-6 LX240T FPGA modules per board
      • 8-lane PCI Express interface
    • EX-300 FPGA cluster
      EX-Series boards are designed for the most demanding FPGA applications (+)

      Features:

      • Use a single EX-Series board as a workstation accelerator, or use multiple boards for cluster computing
      • 16 high-density Xilinx Spartan-3 FPGA devices per board
      • PCI Express interface
  • Nallatech  (15 of 23)
    • BenNUEY-VME
      Based on Xilinx Virtex-II Pro field programmable gate arrays (FPGAs) (+)

      Features:

      • Dedicated PowerPC processor units and increased memory
      • Makes full use of the Virtex-II Pro
      • Support for Gbit Ethernet, Infiniband and Fibrechannel, plus others through two SFP modules on the front-panel interfacing directly to the Virtex-II Pro
    • Benera
      CompactPCI DIME-II motherboard with Xilinx Virtex FPGAs (+)

      Features:

      • 64-bit/33MHz PCI interface
      • PCI master DMA engine capable of 266 Mbytes/sec PCI burst transfers
      • Four DIME-II module slots
    • BenONE-PCI-104
      FPGA processing capability in PCI-104 form factor (+)

      Features:

      • Access to Nallatech's full range of DIME-II FPGA modules for FPGA processing, memory, and analog and digital I/O
      • Supporting Xilinx Virtex-4, Virtex-II Pro and Virtex-II FPGAs through the DIME-II module range
      • Includes embedded PCI interface for communicating with host SBC
    • VXS-620 FPGA
      FPGA and PowerPC VXS multiprocessor (+)

      Features:

      42875.jpg
      • Designed to meet the signal processing needs of modern signal intelligence, software defined radio, and radar applications
      • The VXS-620 is the latest product to be introduced to the highly successful Nallatech REVX Series of rugged embedded processing solutions
      • The VXS-620 features an onboard Xilinx Virtex-5 FPGA for the implementation of high performance DSP applications
    • BenADDA-16™
      Single-width PMC/XMC mezzanine (+)

      Features:

      • Xilinx Virtex-5 LX155T or SX95T FPGA
      • Two banks 256 MB DDR2 SDRAM
      • PCI-X 133 PMC interface
    • FPGA Accelerated Compute Node
      The Nallatech® FPGA Accelerated Compute Node® allows you to drive the most demanding HPC, data visualization and rendering workloads with a flexible, extremely dense 1U rack server optimized for accelerators. (+)

      Features:

      333267492491112286.jpg
      • High Density 1U Rack Server with (2) Intel Xeon Processors
      • (4) Nallatech 510T Cards with (8) Latest- Generation Altera / Intel Arria 10 FPGAs
      • OpenCL Programming Support
    • XMC-220
      FPGA and 16-bit Analog I/O PMC/XMC (+)

      Features:

      • Single-width PMC/XMC mezzanine
      • Xilinx Virtex-5 LX155T or SX95T FPGA
      • Two 16-bit 180 MSps A/D converters
    • Benadic
      A CompactPCI 14-bit ADC motherboard (+)

      Features:

      • Operates at 80 Mbytes/sec with 250Mhz bandwidth for high-performance applications
      • 20 channels integrated into a Xilinx FPGA network
      • Each of the 20 ADCs supports either single-ended or differential analog input. Each FPGA contains a 128Mbyte bank of SDRAM that allows storage of digitized data from each of the ADCs
    • BenNUEY-PCI-104-V4
      PCI-104 FPGA Computing Processor Card (+)

      Features:

      31729.jpg
      • FPGA computing stack that provides a powerful platform for high-performance embedded systems development and deployment in production environments across a variety of applications including signals intelligence, avionics, Software Defined Radio, and autonomous vehicles
      • This solution is suitable for SWAP constrained real time embedded applications
      • An on-board Virtex-4 FX FPGA provides the ideal balance of resources for processing and system management, whilst three DIME-II expansion slots allow users to optimize system resources to meet processing, memory, and I/O requirements
    • BenDATA-II
      Combines the Virtex-II Pro FPGA from Xilinx with the flexibility of both onboard SRAM and DDR SDRAM (+)

      Features:

      • High bandwidth off-module communication is provided through the multi-Gbps bandwidth of the DIME-II motherboard connections in addition to eight Rocket I/O connections
      • Suitable for high-performance FPGA computing applications
      • The Virtex-II Pro FPGA on the BenDATA-II is offered from 2VP70 to 2VP125
    • BenNUEY-VME64-VXS
      6U VME64-VXS FPGA Computing Card (+)

      Features:

      • Provides a powerful platform for high-performance systems development and deployment in production environments
      • Using DIME-II expansion modules, the BenNUEY-VME64-VXS can support multiple analog and digital I/O interfaces, memory types, and up to seven user FPGAs on a single PCI card
      • Can be combined with DIMEtalk for easy connectivity implementation and FUSE for host integration [...]
    • BenBLUE-V4
      Dual Virtex-4 and SRAM module (+)

      Features:

      • Two onboard Xilinx Virtex-4 User FPGAs
      • Two Virtex-4 LX100 or LX160
      • Up to 300k+ logic cells per module
    • VXS-610
      Dual FPGA and PPC multiprocessor VXS card (+)

      Features:

      • Single-slot VXS card
      • PowerPC node with MPC8548E processor
      • Two FPGA nodes with Xilinx Virtex-5 LX155T or SX95T
    • XMC-210
      FPGA and dual 8-bit 3 GSps ADC PMC/XMC (+)

      Features:

      • Single-width PMC/XMC mezzanine
      • Xilinx Virtex-5 LX155T or SX95T FPGA
      • 2 banks 256 MB DDR2 SDRAM
    • 385A
      The 385A™ is a half-height, half-length PCIe 3.0 card featuring Altera’s new floating-point enabled Arria 10 FPGA family capable of delivering 1.5 Peak TFlops of floating point performance. Two independent banks of SDRAM memory and dual QSFP+ network ports complete the balanced architecture capable of both co-processing and latency-critical 1G/10G/40G streaming applications. (+)

      Features:

      310452786761694178.jpg
      • Arria 10 FPGA
      • Delivering 1.5 Peak TFlops of floating point performance
      • Two independent banks of SDRAM memory
  • Sundance Multiprocessor Technology Ltd.  (15 of 17)
    • SMT351
      Embedded reconfigurable computing modules based on Xilinx Virtex-II Pro field programmable gate arrays (FPGA) (+)

      Features:

      • 1 GB of storage in DDR SDRAM (Samsung K4H511638B-GC/LB3 or Micron MT46V32M16FN -6)
      • Up to 400 MBps throughput rate
      • 32-bit data width
    • FC104
      A 1 GSps Digital Down Converter (DDC) IP core (+)

      Features:

      • Fully configureable core developed specifically for Xilinx FPGAs
      • Can be implemented on Sundance's SMT398, SMT388, and SMT368 FPGA-based reconfigurable computing platforms
      • Quad DDC architecture
    • SMT3311
      A CompactPCI FPGA board with five Altera APEX-600E FPGAs, ZBT SRAM, and Sundance Digital Bus (SDB) backplane on J3 (+)

      Features:

      • 128-point to 1 million-point FFT engine radar sonar
      • 16-bit complex input data format
      • 32-bit blocked floating-point output data format, extendable to 64 bits
    • SMT406
      A Tangor FPGA-based processor PMC module (+)

      Features:

      • Tangor processing engine uses a Xilinx Virtex-II from 2V4000 to 2V10000 FPGA as the processing component
      • 128 MB of 133 MHz SDRAM, controlled by the PCI controller and accessible from both the PCI bus and the FPGA
      • Four banks of 4 MB each 200 MHz DDR SRAM connected to the FPGA
    • SMT700 Virtex-5 PXI
      The SMT700 is a PXI express Chameleon board designed for a variety of FPGA-centric applications (+)

      Features:

      • Built around the fastest Virtex-5 FPGA, the SMT700 is a reconfigurable
      • Fastest Xilinx Virtex-5 LXT or SXT FPGA
      • 1 GB DDR2 SDRAM (64-bit)
    • SMT377
      XC2v1000 FPGA (+)

      Features:

      • 1 Mbyte of ZBT RAM
      • Global Bus Technology
      • Eight channels of DAC outputs
    • SMT130
      Onboard XDS-510 compatible JTAG Master (+)

      Features:

      19175.jpg
      • Global bus bandwidth in excess of 100 MBps
      • Host interface via ComPort in excess of 10 Mbps
      • Can support multi-DSP and FPGA resources
    • SMT364
      ADC Module (+)

      Features:

      • 14 Channels
      • 105 Mbps at 14 bit
      • Sundance High Speed Bus
    • SMT498
      An FPGA ProPMC module (+)

      Features:

      • Supports 64 bits 66 MHz PCI bus with data rates of more than 500 MBps
      • PrPMC form factor [...]
    • SMT358
      Single-width module (+)

      Features:

      • Virtextm range of FPGA devices as user programmable resource
      • 1M Gates equivalent or more of software configurable resource
      • 4 banks of 1M x 18 of high-speed ZBT SRAM
    • SMT339
      Combining a Texas Instruments TMS320DM642 DSP-based digital media processor at 720 MHz and a Xilinx Virtex-4 FX-60 FPGA, the SMT339 packs huge compute power into a small development board (+)

      Features:

      • Software support includes TI's Code Composer Studio Integrated Development Environment (IDE) and 3L's Diamond FPGA
      • Interfaces include serial ports or the Rocket Serial Link
      • Used with a TIM carrier such as the SMT130 for PCI-104 or standalone, designers can be up and running quickly [...]
    • SMT398
      Single width module (+)

      Features:

      10256.jpg
      • Virtex range of FPGA devices as user programmable resource
      • Up to 8M Gates equivalent or more of software configurable resource
      • 2 Banks of high speed ZBT SRAM
    • SMT8090
      A development platform for the wireless and telecommunication markets (+)

      Features:

      18580.jpg
      • Two daughtercards (SMT338-VP and SMT390) are sandwiched together on a PCI carrier board
      • Two floating-point Ti TMS320C6713 processors at 225 MHz
      • Xilinx Virtex-II Pro (2VP30) FPGA with two IBM 400-MHz PowerPC processors and eight 3.125-Gbps, full-duplex serial links
    • SMT407
      A PMC module that supports 64 bits 66 MHz PCI bus (+)

      Features:

      • Uses two TMS320C6416T DSPs with clock speeds of 1 GHz
      • Includes a Xilinx VirtexII-Pro (XC2VP50FF1152) FPGA configured to provide ‘C4x style comm-ports, either two Sundance High-Speed Buses (SHBs), or one SHB and one FPDP interface through a programmable I/O daughter module, 12 Sundance RSL, and other control functions [...]
    • SMT356
      Simple implementation of multichannel solutions (+)

      Features:

      • Scalable system configuration
      • Direct connection from ADC to C6000 DSPs
      • Clock enable enhances control of data capture for burst mode applications
  • Macraigor Systems, LLC  (2)
    • J-SCAN 2.1
      J-SCAN Version 2.1, the newest release of its high-speed, low-cost boundary-scan debug and programming tool. (+)

      Features:

      • This new technology allows circuit designers to facilitate early test development, thereby shortening the development cycle and prototyping process.
      • Version 2.1 of J-SCAN communicates to the target with a USB 2.0- and USB 1.1-compatible interface that runs in high speed or full speed modes.
      • This gives a performance increase of more than 10X compared to the previous version of J-SCAN. Additionally, J-SCAN 2.1 has full support for serial peripheral interface (SPI) Flash programming, supporting those systems using field-programmable gate arrays (FPGAs) and other embedded devices.
    • J-Scan Debugging and Programming Tool
      Accelerates development cycle and prototyping process (+)

      Features:

      20868.jpg
      • Instantly programs IC devices, FPGAs, and CPLDs [...]
  • Intilop  (1)
    • FPGA accelerator board with network
      Intilop’ full transmission control protocol (TCP) and user datagram protocol (UDP) accelerator with network security capability performs functions of firewall and other monitoring functions at full line rate. (+)

      Features:

      3694723438611344585.jpg
      • The full TCP/UDP offload (TOE) core performs protocol offload of all phases of TCP/Internet Protocol (IP) software in high-performance field-programmable gate arrays (FPGAs), without central processing unit (CPU) involvement.
      • The security module can be removed from the base-TOE core. These functions are performed in 100 nanoseconds at full 10G bps and 40G bps line rate with ultra-precision and zero jitter. [...]
  • CSP Inc. (CSPI) MultiComputer Division  (3)
    • FastCluster XL-Gate
      The XL-Gate provides a Hybrid Computing Solution delivering the acceleration of Virtex-5 FPGAs and the optimized performance/power ratio of a MPC8641 General Purpose Processor (+)

      Features:

      43508.jpg
      • The reconfigurable XL-Gate FPGA payload supports Xilinx Virtex-5 LXT or SXT FPGA's (on an XMC Module)
      • FPGA development is simplified by the use of the CoreFire Design Suite, turning high-level data flow concepts into algorithms programmed for the XL-Gate FPGA board
      • Available in air-cooled or conduction cooled versions
    • 3000 SERIES
      A series of VXS systems that support multicore, FPGA, and 10 GbE interoperability while delivering a 5x performance increase in bisection bandwidth over the previous generation (+)

      Features:

      32170.jpg
      • Rugged, high-performance scalable embedded cluster with general purpose processors, reconfigurable FPGAs, and high-speed interconnect on VXS
      • VXS switch with Myri-10G Clustering Technology and 10 GbE compatibility
      • VXS payload with Freescale multicore PowerPC AltiVec
    • FPGA Development Platform
      The CSPI FPGA Development Platform includes advanced tools needed to accelerate the design, build, and test phase of your DSP application for the FastCluster Run-time Platform (+)

      Features:

      43507.jpg
      • The FPGA Development Platform for FastCluster supports a Virtex-5 FPGA XMC development board, Java SE Development Kit, Xilinx ISE, Microsoft Visual Studio and the CoreFire Design Suite
      • The FastCluster FPGA Run-time Platform includes an FPGA payload, drivers, library, Board Support Package, and Debugger Agent
      • Development and Run-Time Platforms use the same FPGA (Xilinx Virtex-5) XMC modules [...]
  • Mercury Systems  (15 of 17)
    • PowerStream 7000 FCN
      An FPGA Compute Node (FCN) that can incorporate up to 69 Xilinx 7 million-gate FPGAs connected by a RapidIO switch fabric (+)

      Features:

      31382.jpg
      • Includes up to 46 10-Gigabit fiber connections directly to the FPGAs
      • 320 Gbps of I/O available in the base configuration
      • Base configuration uses PowerPC 7447A processors connected by a RapidIO switch fabric
    • ECDR-4-14105
      Four A/D converters (14-bit at 105 MHz sampling rate); each followed by an Altera Stratix FPGA with custom IP to implement a wide band receiver and FFT engine (+)

      Features:

      • Two large user-programmable Xilinx Virtex-II Pro FPGAs each with a total of 512 MByte DDR SDRAM. These FPGAs connect directly to each other through four LVDS data links that each provide 622 MBytes/second throughput
      • The FPGA resources are also available to implement custom processing functions (beamforming, direction-finding, etc.) according to user specifications
      • One control/output FPGA with associated 256 MByte DDR SDRAM which outputs data to the appropriate data bus, dual RACE++, serial Rapid I/O, or other Vita 41-defined protocol
    • RACE++ FPGA Compute Nodes
      FPGA compute nodes fully integrated into a RACE++ VME system (+)

      Features:

      • Easy application partitioning between FPGAs and PowerPCs
      • Off-the-shelf IP Provides RACE++ and memory interfaces
      • FPGA Developer's Kit (FDK) simplifies FPGA code development
    • Echotek Series SCFE-V5-VXS
      The Echotek Series SCFE-V5-VXS Virtex-5 FPGA-Based Processing Engine provides high-performance processing for applications requiring extreme FPGA processing power (+)

      Features:

      42271.jpg
      • Utilizing the largest FPGAs available from Xilinx, the SCFE-V5-VXS solves the toughest computing problems in a cost-effective form factor
      • The other interfaces on the card, including the QSFP fiber transceivers, and the FMC mezzanine sites, combine with the FPGA processing power to create an interoperable, upgradeable solution for a vast number of platform configurations
      • Three Xilinx Virtex-5 SX240T or LX330T FPGAs in 1,738 pin-package with up to 3,168 raw DSP48e slices
    • Echotek Series ECV4-2
      The ECV4-2, with input clock capability up to 1.5 GHz, is the highest performing digital receiver in an XMC form factor in the industry (+)

      Features:

      • Echotek Series products lead the mixed-signal industry in extracting clear signals from electronic clutter, forming a bridge between the realms of analog signals and digital processing. After an analog signal is received by an antennae or other sensor, it must be digitized and manipulated into a form amenable to signal processing. The challenge, and the key to successful applications, is to manage this transformation in real time while maintaining the integrity of the original signal
      • Processing power is delivered by a Xilinx Virtex-4 FPGA (field-programmable gate array). This FPGA allows users to run customized algorithms such as digital down/up conversion (wideband or narrowband), Fast Fourier Transforms (FFTs), and filtering directly on the ECV4-2. Modules are available in air-cooled or conduction-cooled versions [...]
    • Momentum Series AXA-110 AMC
      Momentum Series AXA-110 Advanced Mezzanine Card (AMC), which uses a dual-core Intel processor combined with an FPGA (field-programmable gate array) for flexible switch fabric connectivity (+)

      Features:

      32646.jpg
      • AMCs provide the modularity for demanding telecom and military communications, and the AXA-110 is ideally suited for the processing and communications heart of AdvancedTCA or MicroTCA systems
      • The Momentum Series AXA-110 is Mercury's second generation of AMC cards that combine a dual-core Intel processor with the latest Xilinx FPGA. The AXA-110 is the first AMC to incorporate an Intel Core 2 Duo processor, which yields more than 25 percent overall performance improvement than an Intel Core Duo processor, and more than double the overall performance of Intel Pentium M processor, as measured by SPECint_rate_base2000
      • The key to accessing the substantial processing power is the connectivity provided by the serial fabric interfaces on the AMC. Using a Xilinx Virtex-5 FPGA, the AXA-110 connects to up to 16 high-speed serial lines totaling 40 Gigabits per second
    • MCJ6 FCN Module
      A module that integrates FPGAs into RACE++ VME multicomputers (+)

      Features:

      17596.jpg
      • 6U VME board with two Xilinx Virtex II Pro P70 FPGAs connected to a RACE++ switch fabric via an onboard crossbar
      • Eight serial copper interfaces, 12 serial fiber optic interfaces, and 52 pairs of LVDS I/O
      • More than 5 GBps of I/O
    • Echotek Series ECV4-4
      The Echotek Series ECV4-4 family of digital receivers implements a flexible baseboard plus mezzanine architecture while supporting an extremely high density of FPGA-processing power (+)

      Features:

      • This combination of flexibility and power allows the family to deliver unique capabilities, such as multi-board coherency, while addressing a range of analog signal requirements
      • Seven user-programmable Virtex-4 FPGAs plus one Stratix FPGA
      • Multiple backplane interfaces for VXS, RACE++, and VME64x
    • PowerStream 6600
      A fully integrated, conduction-cooled multicomputer based on the VPX-REDI draft standards (+)

      Features:

      31429.jpg
      • 16 payload modules can house 64 PowerPC processors or a heterogeneous mix of PowerPCs and Xilinx Virtex-4 FPGAs
      • Conduction-cooled format based on VPX-REDI standard (draft) form factor
      • RapidIO fabric supports an aggregate system bandwidth exceeding 34 GBps and a bisection bandwidth of 16 GBps
    • ECAD-X-081500
      A VME64x, A/D converter board (+)

      Features:

      • Provides either one or two channels of 8-bit, 1.5 GHz analog-to-digital conversion and programmable FPGAs in a single, 6U VME64x slot
      • Uses Maxim MAX108 A/D converters, providing SFDR in excess of dBFS for input intermediate frequencies (IF) up to 1 GHz and A/D sample rates from 100 MHz to 1.5 GHz
      • Front-panel connectors are provided for the following input signals: analog input, A/D clock, sync signals, trigger, 128-bit auxiliary input, and LVDS I/O
    • Echotek Series SCFE-V6-4QSFP-OVPX
      6U OpenVPX fiber I/O module (+)

      Features:

      • Combines 16 channels of high-speed fiber with three Xilinx Virtex-6 FPGAs to achieve a maximum data transfer capacity of 80 Gbps
      • The module is well suited to support the high-bandwidth digitized I/O created by various commercial and defense applications including the current generation of advanced ISR sensors
      • Each of the 16 channels of fiber supports a full duplex data rate up to 5 Gbps, while the three FPGAs enable onboard pre-processing of data streams for maximum application effi-ciency
    • Echotek DCM-V5-VXS
      Echotek Series DCM-V5-VXS Virtex-5 Based FPGA Digital Receiver (+)

      Features:

      42112.jpg
      • Twin FPGA Mezzanine Card (FMC) modules equipped with two each of the following ADCs: 16-bit 130 MSps ADC converters, 14-bit 250 MSps ADC converters, or 10-bit 1.5 GSps ADC converters, with other options available
      • Three Xilinx Virtex-5 SX240T or LX330T FPGAs
      • DDR-II SDRAM and QDR-II SRAM
    • Echotek ECV4-2
      A family of mixed-signal PMC and XMC modules that serve as high-performance digital receivers for the mixed-signal industry (+)

      Features:

      • Two Virtex-4 FPGAs for data processing and PCI/PCI-X interfacing
      • PMC/PCI form factor
      • Preloaded FPGA development IP
    • Ensemble IOM-300 series
      The Ensemble IOM-300 series are the industry’s first open systems architecture-based XMC modules to feature two FPGA devices for streaming sFPDP, Ethernet and other wideband protocols. The primary Altera industrial-grade Stratix V FPGA is a highly customizable processing resource for low-latency signal processing supported by a second configuration FPGA that enables in-mission, real-time FPGA image refreshes for the Stratix V. Each of the module’s twelve channels may be programmed for data distribution, with or without user customization, via the primary FPGA device. (+)

      Features:

      322840858621356724.jpg
      • Twelve channel, front-panel access fiber I/O or eight channel copper I/O ports
      • Supporting sFPDP (VITA 17.1), 10Gb/s Ethernet, Fibre Channel and unrestricted PCIe Gen 3 data rates
      • Altera Stratix V FPGA with second FPGA programing and personalized security capability
    • ECDR-112-E
      100 MHz EFFECTIVE BANDWIDTH (460 MSPS) (+)

      Features:

      • 12 BIT A/D CONVERTERS; 4 TIMES OVERSAMPLING
      • A/D AUTO-CALIBRATION
      • 16 BIT ACCURATE NCO
  • Synopsys, Inc.  (1)
    • Synplify Premier
      The Synopsys FPGA design solution comprises high-quality, high-performance, and easy-to-use FPGA implementation and debug tools (+)

      Features:

      46489.jpg
      • Designers using the Synopsys FPGA design tools gain fast time-to-results for complex FPGAs, area optimization for cost and power reduction, multi-FPGA vendor support, and incremental and team-design capabilities for faster FPGA design development
      • The Synopsys FPGA design tools also provide additional value by offering DesignWare IP integration, links to high-performance functional verification with VCS, integration with Synphony Model Compiler, and an ASIC compatible synthesis flow for FPGA-based prototyping
      • As part of the Synopsys FPGA Design Solution, Synplify Premier software performs FPGA synthesis for programmable devices sold by Actel, Achronix, Altera, Lattice Semiconductor, Silicon Blue and Xilinx
  • Extreme Engineering Solutions (X-ES)  (2)
    • XCalibur5090
      The XCalibur5090 is a high-performance, reconfigurable, conduction-cooled 6U LRM module featuring dual Xilinx Virtex-7 FPGAs, high-speed serial interfaces, DAC and ADC channels, external memory, and flexible, high-density I/O. The XCalibur5090 utilizes four AD9739 and two ADC12D1600RF to provide four channels of high-frequency 14-bit Digital Analog Conversion (DAC) at 2500 Mbps and four channels of 12-bit Analog Digital Conversion (ADC) at 3200 Mbps for high-performance Digital Signal Processing (DSP). (+)

      Features:

      314776900022905961.jpg
      • Two Xilinx Virtex-7 XC7VX690T FPGAs
      • Up to 1 GB of DDR3 SDRAM per FPGA in two channels
      • Non-volatile FPGA configuration flash
    • XPedite2403
      XPedite2403 is a high-performance, reconfigurable, conduction- or air-cooled XMC module based on the user-programmable Xilinx Virtex-7 family of FPGAs. With dual x8 PCI Express Gen3 interfaces, external memory, 24 high-speed fiber-optic receivers, and 8 GB of DDR3-1600 SDRAM in two channels, the XPedite2403 is ideal for customizable, high-bandwidth, data-processing, and data acquisition applications. It incorporates 24 high data rate, protocol-independent fiber-optic receivers that comply to ARINC 804 and utilize 50/125µm multi-mode fiber with MT connectors. (+)

      Features:

      347264910022123999.jpg
      • Xilinx Virtex-7 FPGA XC7VX690T
      • Conduction- or air-cooled XMC module
      • Twenty-four 10.3125 Gb/s optical receiver links
  • Alorium Technology  (1)
    • XLR8: FPGA-based Development Board
      XLR8 is a drop-in replacement for an Arduino Uno. It is an Arduino-compatible board that uses a Field-Programmable Gate Array (FPGA) as the main processing chip. The FPGA hosts an ATmega328 instruction set compatible microcontroller and allows for implementation of custom logic to accelerate functionality that is slow or problematic for 8-bit microcontrollers. XLR8 significantly improves performance in the same physical footprint as standard Arduino Uno and is programmed with the Arduino IDE. XLR8 also provides a great platform for learning the basics of FPGA design. (+)

      Features:

      342946750832273546.jpg
      • Faster Application Speeds
      • Higher Computational Performance
      • Customizable
  • Impulse Accelerated Technologies  (8)
    • Acceleration Station P-300L
      Desktop workstation for software application developers researching FPGA-based algorithm acceleration (+)

      Features:

      • Over 1.2 million programmable logic elements usable from C
      • Pico Computing EX-300 accelerator card
      • 16 Xilinx Spartan XC3S5000 FPGAs
    • Impulse CoDeveloper, Impulse C
      Enter device independent FPGA designs using ANSI C and compile into Altera or Xilinx (+)

      Features:

      • Work within Visual Studio, GCC, Eclipse, or other standard IDEs
      • Cab mix with VHDL code if desired
      • Identify hotspots for acceleration
    • FeedHandlingKit
      Feed Handling system which builds on COTS FPGA based hardware to accelerate processing speed while protecting your company's intellectual property (+)

      Features:

      • Acceleration – FPGA based hardware/software systems can accelerate some feed handling systems by 100x over pure microprocessor solutions
      • Protection of Intellectual Property – this methodology enables solution providers to offer the ability for end-users to insert custom functions, and to do so without accessing the IP provided by the solutions provider
      • Reusable, Retargetable and Portable – because the code remains in C and synthesizable VHDL it can be easily moved to improved hardware as newer platforms emerge
    • Impulse CoDeveloper
      High-level FPGA design software (+)

      Features:

      • Allows C-language algorithms and applications to be compiled and optimized for use with FPGAs
      • By using Impulse C and the Impulse CoDeveloper C-to-FPGA tools, users have the power to accelerate C algorithms by orders of magnitude (as much as 300X) over equivalent embedded processor implementations
      • Enter designs in ANSI C
    • CoDeveloper for Virtex II Pro
      A C-to-FPGA, hardware/software co-design system for PowerPC-based Xilinx FPGAs (+)

      Features:

      • Allows users to describe, test, and compile C language applications, partitioning them between the Virtex II Pro's embedded PowerPC processor
      • Allows FPGA algorithms to be developed using popular C/C++ development environments, including Microsoft Visual Studio, Metrowerks CodeWarrior, and open-source GCC-based tools
      • Automates hardware/software interface creation and generates synthesizable HDL outputs compatible with popular FPGA synthesis and simulation tools [...]
    • Impulse C-to-FPGA Tools
      Software-to-FPGA tools (+)

      Features:

      • Work with BlueCat Linux from LynuxWorks
      • Enable software developers to write C algorithms and refactor them for parallel processing on an FPGA
      • 10 – 100x performance increase in image, signal, and data processing algorithms
    • C to FPGA Video Kit
      Video Processing FPGA Developer's Kit for rapid design of medical, military, automotive, and consumer electronics video systems (+)

      Features:

      • C to FPGA compilation
      • Analysis of C for opportunities to accelerate code through increased parallelism, unrolling loops and adjusting stage delays
      • Machine-generated parallelism/optimization
    • FPGA Image Proc Lib
      FPGA image processing elements for developing custom advanced video and imaging systems includes a range of single-pixel and 2-dimensional operations. Integrates into Impulse C (+)

      Features:

      • C-callable functions as well as process-level filters that operate on streaming video data
      • Integrates directly into Impulse C
      • Compatible with Visual Studio, GCC, Eclipse and other popular environments
  • Curtiss-Wright  (15 of 19)
    • CHAMP-FX2
      The CHAMP-FX2 is Curtiss-Wright's next-generation FPGA-based computing platform utilizing a 6U VPX-REDI form factor (+)

      Features:

      • Two Xilinx Virtex-5 Platform FPGAs (LX110T, LX220T, or LX330T)
      • 512 Mbytes or 1 GB DDR2 SDRAM per FPGA in two banks (1-2 Gbyte total on-board), 4.4 GBytes/sec peak bandwidth per FPGA
      • 36 Mbytes QDR-II+ SRAM per FPGA in four banks (72 Mbytes total on-board), 8.8 GBytes/sec peak bandwidth per FPGA
    • FPE-320 3U VPX Processor Board
      The FPE320 is a 3U VPX FPGA processor board that incorporates the largest Xilinx Virtex-5 FPGAs available with an FPGA Mezzanine Card (FMC) site (+)

      Features:

      46493.jpg
      • Providing many resources in a small, rugged form factor, the FPE320 is the ideal FPGA platform for 3U systems that need to acquire analog and other high-speed I/O, or that need a large FPGA processor
      • At the heart of the FPE320's processing is a Xilinx Virtex-5 FF1738 package FPGA, the largest FPGA in the Virtex-5 family
      • FPGAs provide parallel processing capabilities that can be used to reduce processor count and system size
    • FPE650 FPGA VPX
      A quad FPGA processor card which combines high bandwidth I/O, achieved through VPX/VPX-REDI and FMC/VITA 57 sites (+)

      Features:

      36805.jpg
      • Designed for the most demanding digital signal processing applications such as electronic counter measures, signal intelligence, and electro-optics
      • Four Xilinx LXT, SXT, or FXT Virtex-5 FPGAs
      • 4x Xilinx Virtex-5 FPGAs (SX95T, LX155T, FX100T)
    • CHAMP-FX4 6U OpenVPX Xilinx Virtex-7 FPGA Processor Card
      The CHAMP-FX4 is the flagship 6U product in Curtiss-Wright Defense Solutions’ family of user-programmable Xilinx® Virtex®-7 FPGA-based computing products, designed to meet the needs of challenging embedded high-performance digital signal and image processing applications. Curtiss-Wright's 4th generation 6U FPGA card, the CHAMP-FX4 combines the dense processing resources of three large Xilinx Virtex-7 FPGAs with over 12 GB of memory resources, all on a rugged 6U OpenVPX (VITA 65) form factor module. (+)

      Features:

      • OpenVPX (VITA 65) profile MOD6-PAY- 4F1Q2U2T-12.2.1-11
      • VPX REDI (VITA 48 option)
      • Three user-programmable Xilinx Virtex-7 FPGAs (585T or X690T), each with: 4 GB DDR3L SDRAM in two 64-bit banks, 36 MB QDRII+ SRAM in two 36-bit banks
    • CHAMP-FX2 MPC8640 & Virtex-5 VPX Digital Signal Processor
      Two Xilinx Virtex-5 FPGAs (LX110T or LX220T) (+)

      Features:

      • 512 MB or 1 GB DDR2 SDRAM per FPGA in two banks (1-2 GB total onboard), 4.4 GBps peak bandwidth per FPGA
      • 36 MB QDR-II+ SRAM per FPGA in four banks (72 MB total onboard), 8.8 GBps peak bandwidth per FPGA
      • 1 GHz MPC8640D dual-core processor with 512 MB of DDR2 SDRAM in two banks
    • CHAMP-FX2 FPGA DSP
      The CHAMP-FX2 is Curtiss-Wright's next-generation FPGA-based computing platform utilizing a 6U VPX-REDI form factor (+)

      Features:

      34875.jpg
      • Two Xilinx Virtex-5 Platform FPGAs (LX110T, LX220T, or LX330T)
      • 512 Mbytes or 1 GB DDR2 SDRAM per FPGA in two banks (1-2 Gbyte total on-board), 4.4 GBytes/sec peak bandwidth per FPGA
      • 36 Mbytes QDR-II+ SRAM per FPGA in four banks (72 Mbytes total on-board), 8.8 GBytes/sec peak bandwidth per FPGA
    • XF07-523 Kintex-7 FPGA XMC
      The XF07-523 provides direct FPGA driven LVDS I/O through the front panel and PMC/XMC connectors for rear I/O on a fully ruggedized XMC module designed to perform optimally in the harshest conditions including +85C card edge conduction-cooled solutions. This high performance module is ideal for use in a wide range of applications that require high-speed FPGA based digital I/O such as avionics, radar, digital imaging, and FPGA co-processor and other test equipment. (+)

      Features:

      212842378121582232.jpg
      • Based on Xilinx Kintex-7 325T (speed grade 2) FPGAs
      • High performance, high bandwidth LVDS digital I/O on front panel and rear IO
      • Dual x16 DDR3 memories for > 5 Gbytes/sec usable bandwidth
    • CHAMP-FX2 VPX FPGA & MPC8641D Processor
      A 6U VPX-REDI/VPX/OpenVPX hybrid processor (+)

      Features:

      • Two Xilinx Virtex-5 LX110T/LX220T FPGAs
      • Freescale MPC8641/8641D processor @ 1.0 GHz
      • XMC site
    • HPE720
      6U VPX Hybrid Processing Engine with a MPC8641D and dual Xilinx Virtex-5 FPGAs (+)

      Features:

      • Single or dual-core Freescale MPC8641D processor at 1.0/1.25/1.33 GHz
      • Dual Xilinx Virtex-5 FPGAs (LX110/220/330T, SX240T, or FX200T options)
      • Dual FPGA Mezzanine Card (FMC/VITA 57) sites or 1 FMC and 1 XMC/PMC site
    • CHAMP-FX4 6U OpenVPX Virtex-7
      The CHAMP-FX4 is the flagship 6U product in Curtiss-Wright Defense Solutions’ family of user programmable Xilinx® Virtex®-7 FPGA-based computing products, designed to meet the needs of challenging embedded high performance digital signal and image processing applications. Curtiss Wright’s 4th generation 6U FPGA card, the CHAMP FX4 combines the dense processing resources of three large Xilinx Virtex-7 FPGAs with over 12 GB of memory resources, all on a rugged 6U OpenVPX (VITA 65) form factor module. (+)

      Features:

      292163107861464693.jpg
      • Over 100 GB/s of backplane I/O bandwidth
      • Gen2 Serial RapidIO (SRIO) provides standards-based connectivity to general-purpose processing boards such as the VPX6-1957 and CHAMP-AV8
      • Two FMC interfaces with 80 differential signal pairs
    • FPE320 3U Processor
      3U VPX FPGA processor board that incorporates the largest Xilinx Virtex-5 SXT, LXT or FXT FPGA available with an FMC mezzanine site (+)

      Features:

      39100.jpg
      • Supports Xilinx Virtex-5 SXT, LXT and FXT FPGAs
      • FMC (VITA 57) mezzanine site for I/O
      • DDR2 SDRAM and QDRII SRAM memory resources
    • CHAMP-WB-A25G
      The CHAMP-WB-A25G couples the dense processing resources of a single large Xilinx Virtex-7 FPGA with a high-bandwidth 25 GS/s 8-bit ADC module in a commercial grade 6U OpenVPX (VITA 65) form factor module. The 25G ADC module can also operate in a dual channel 12.5 GS/s mode. The CHAMP-WB-A25G complements this processing capability with a data plane directly connected to the FPGA with support for Gen2 Serial RapidIO (SRIO) or Aurora up to 10.3 Gbps. (+)

      Features:

      320749380221646148.jpg
      • 6U OpenVPX Wideband Receiver with 25 GS/s ADC
      • Onboard PCIe Gen3 switch
      • Single user-programmable Xilinx Virtex-7 FPGAs X690T, with 8 GB DDR3L SDRAM
    • XF07-516 Quad 250MSPS 16b XMC
      The XF07-516 is a rugged quad channel 250MSPS 16-bit digital receiver XMC. The ADC devices are controlled by a user programmable Xilinx FPGA which allows high performance processing such as Digital Down Conversion (DDC), filtering and custom algorithms. The XF07-516 Kintex-7 FPGA XMC is available in air and conduction-cooled build variants. The XF07-516 Kintex-7 FPGA XMC supports two banks of 128M x 16-bit DDR3 SDRAM, each directly connected to the FPGA. (+)

      Features:

      226606118407546982.jpg
      • 4 x 250 MSPS 16-bit Digital Receiver
      • XMC (x8 PCIe) module in air-cooled and conduction-cooled models
      • 80-250MHz external sample clock input (MMCX)
    • VPX3-530 3U VPX Virtex-7 FPGA Digital Receiver
      The VPX3-530 is a rugged dual channel 4GSPS ADC/DAC card with a user programmable Xilinx Virtex-7 FPGA in a 3U VPX ADC/DAC form factor. Providing two 4GSPS 12-bit (or four 2GSPS) analog inputs and two 5.6GSPS update rate (maximum 2.8GSPS data rate) 14-bit analog outputs with XC7V690T FPGA in air and conduction-cooled formats means that the VPX3-530 is ideal for a SWaP constrained range of defense applications such as Radar Warning Receivers (RWR), SIGINT and ECM applications. The VPX3-530 3U VPX Xilinx Virtex-7 FPGA ADC/DAC Card can be used in simple configurations alongside a Single Board Computer (SBC) or as part of a larger array of synchronized high speed analog I/O solutions. The VPX3-530 3U VPX Xilinx Virtex-7 FPGA ADC/DAC Card combines the I/O resources of the ADC, DACs, high-speed DDR3 SDRAM, high-speed PCI Express (PCIe) and serial links together with FPGA driven parallel IO to the OpenVPX backplane. FEATURES: Analog Inputs: 2x 4 GSPS or 4x 2 GSPS at 12-bit Analog Outputs: 2x 5.6GSPS update rate at 14-bit FPGA: Xilinx Virtex-7 VX690T, speed grade 2 Memory: 2x 2 or 4GB banks, 64-bit data per bank of DDR3L SDRAM OpenVPX Profile: MOD3-PAY-1D-16.2.6-2 and MOD3-PER-1F-16.3.2-2 [...] (+)

      Features:

    • VPX3-450
      The VPX3-450 combines the tremendous computing power of a Xilinx Virtex-5 FPGA with the high-performance floating-point capabilities of the Freescale 8640D dual-core PowerPC (+)

      Features:

      41193.jpg
      • One Xilinx Virtex-5 Platform FPGA (LX155T, or SX95T)
      • 512 MB DDR2 SDRAM attached to the FPGA, 2.2 GBps peak bandwidth
      • 18 Mbytes QDR-II+ SRAM attached to the FPGA in two banks, 4.4 GBps peak bandwidth per FPGA
  • Annapolis Micro Systems, Inc.  (15 of 22)
    • WILDSTAR UltraKVP ZPB for 6U & 3U OpenVP
      Annapolis FPGA boards are engineered for superior performance and maximum bandwidth. Both Altera and Xilinx FPGAs are leveraged to offer the best FPGA technology available and to fit customer preference, design requirements and production schedule. These FPGA boards paired with Annapolis OpenVPXcompliant 6U/3U backplanes enable even the most bandwidth-intensive applications. Rugged UltraKVP ZPB FPGA boards are designed from the ground up to withstand a broad temperature range: -55Ë? to +85Ë?C. [...] (+)

      Features:

      3756237598613608171.jpg
    • WILDSTAR A5 for OpenVPX 6U
      These FPGA boards include 3 Altera Stratix V FPGAs with 48 High Speed Serial connections performing up to 14.1 Gbps. On each Compute Processing Element (CPE) FPGA there is six 72-bit QDRII+ SRAM interfaces clocked up to 550 MHz. The IO Processing Element (IOPE) FPGA has four 32-bit DDR3 DRAM ports clocked at up to 800 MHz. With included High Speed Serial (HSS) FPGA cores (including 40GBASE-KR), there is up 20 GB/s of bandwidth on the VPX data plane which can go directly to other VPX cards or to a switch, depending on backplane topology. (+)

      Features:

      • One, Two or Three ALTERA STRATIX® V FPGAS
      • PCIe Gen3 8x from each FPGA to on-board PCIe switch
      • 16x High Speed Serial IO lanes to VPX Data Plane (P1) for 20 GB/s of Full Duplex Bandwidth
    • WILDSTAR 7 Conduction Cooled for OpenVPX 6U
      These FPGA boards include two Xilinx Virtex 7 FPGAs with 64 High Speed Serial connections performing up to 13.1 Gbps. The IO Processing Element (IOPE) FPGA has a choice of QDRII+ SRAM or DDR3 DRAM. The DRAM option has four 32-bit DDR3 DRAM ports clocked at up to 800 MHz while the SRAM option has two 72-bit QDRII+ SRAM interfaces clocked up to 500 MHz. With included High Speed Serial (HSS) FPGA cores (including 40GBASE-KR), there is up 20 GB/s of bandwidth on the VPX data plane which can go directly to other VPX cards or to a switch, depending on backplane topology. (+)

      Features:

      • One or Two XILINX VIRTEX 7 FPGAS: VX690T or VX980T
      • Up to 8 GB of DDR3 DRAM for 51.2 GB/s of DRAM bandwidth or up to 64 MB of QDRII+ SRAM for 32 GB/s of SRAM bandwidth
      • PCIe Gen3 8x from each FPGA to on-board PCIe switch
    • CoreFire FPGA Development Tool Suite
      The CoreFire Design Suite is a Graphical User Interface (GUI) tool using Data Flow Methodology which combines Annapolis's extensive systems and application development experience with their large collection of tightly crafted high performance Intellectual Property (IP) Cores (+)

      Features:

      16201.jpg
      • With CoreFire TM it is possible to completely implement an algorithm on our WILD TM Family of Field Programmable Gate Array (FPGA) boards without ever descending to the lower level hardware details [...]
    • Wildstar 6 for OpenVPX
      Our 14th-generation WILDSTAR 6 for OpenVPX uses Xilinx's newest Virtex-6 FPGAs for state-of-the-art performance (+)

      Features:

      45439.jpg
      • Up to three Virtex-6 FPGA processing elements - XC6LX240T, XC6LX365T, XC6LX550T, XC6SX315, or XC6SX475
      • Up to 7 GB DDR2 DRAM in 14 banks or up to 448 MB DDRII or QDRII SRAM
      • OpenVPX backplane
    • Wildstar 6 for OpenVPX
      Our 14th-generation WILDSTAR 6 for OpenVPX uses Xilinx's newest Virtex-6 FPGAs for state-of-the-art performance (+)

      Features:

      45439.jpg
      • Up to three Virtex-6 FPGA processing elements – XC6LX240T, XC6LX365T, XC6LX550T, XC6SX315, or XC6SX475
      • Up to 7 GB DDR2 DRAM in 14 banks or up to 448 MB DDRII or QDRII SRAM
      • OpenVPX backplane
    • WILDSTAR II
      A COTS, high-speed DSP board, using Xilinx's Virtex II FPGAs as the processing elements (+)

      Features:

      25824.jpg
      • Suitable for radar, sonar, SIGINT, ELINT, DSP, FFTs, communications, software radio, encryption, image processing, and prototyping applications
      • Accepts the WILDSTAR line of I/O daughtercards [...]
    • Wild40 for PCIe FPGA Boards
      Range of FPGAs to choose from (+)

      Features:

      333792402861309046.jpg
      • PLX PCI Express Gen3 Switch
      • Xilinx® Zynq-7000 SoC
      • Provides dedicated AXI bus to FPGA for register access without requiring PCIe interface
    • WILDSTAR UltraKVP for OpenVPX 6U & 3U
      WILDSTAR UltraKVP FPGA boards utilize Xilinx Kintex FPGAs, which feature the most multipliers currently deployable, or UltraScale+ FPGAs, which feature 28Gb signaling capability! These FPGA cards are hot-swappable and paired with Annapolis OpenVPX compliant 6U/3U backplanes, enabling even the most bandwidth-intensive applications. All Annapolis COTS boards are rugged, open, deployable, and offer different cooling options, making them the most cutting-edge Xilinx-based products on the market. (+)

      Features:

      344672717861844727.jpg
      • Up to three Xilinx® Kintex® UltraScaleâ„¢ XCKU115, Virtex® UltraScaleâ„¢ XCVU125/XCVU190 or Virtex® UltraScale+â„¢ XCVU5P/XCVU9P FPGAs
      • Dual core ARM Cortex-A9 Processor (Zynq SoC)
      • A Full Board Support Package using Open Project Builder for fast and easy Application Development
    • 24 GHz A/D CPD System
      Clock and synchronize up to 16 channels of 1.5 Hz A/D (+)

      Features:

      • Full bandwidth A/D data collection
      • Full bandwidth processing with up to five Virtex II Pro FPGAs per VME slot
      • Full bandwidth data distribution
    • CoreFire Next
      The CoreFire Next Design Suite (compatible with all Annapolis Virtex™ 7 and Altera Stratix® V FPGA processor and I/O boards) is a dataflow-based development system that brings new levels of ease and speed to FPGA programming on Annapolis Micro Systems, Inc. high-performance motherboards, I/O cards, and mezzanine cards. (+)

      Features:

      308663900861183040.jpg
      • Build Designs for FPGAs on WILDâ„¢ Boards
      • Works from High Level, Data Flow Concept of the Application
      • Combines GUI Design Entry and Debug Tools with Tested, Optimized CoreFire Nextâ„¢ IP Cores
    • WILDSTAR 4 for VME
      A tenth-generation WILDSTAR 4 for VME64x/VXS FPGA-based processing board that uses Xilinx's newest Virtex-4 FPGAs for state-of-the-art performance (+)

      Features:

      33245.jpg
      • Accepts one or two I/O mezzanine cards in one VME64x or VXS slot, including single 1.5 GHz 8-bit ADC, quad 250 MHz 12-bit ADC, single 2.5 GHz 8-bit ADC, quad 130 MHz 16-bit ADC, dual 2.3/1.5 GSps 12-bit DAC, quad 600 MSps 16-bit DAC, universal 3 Gb Serial I/O (Rocket I/O, 10 GbE, InfiniBand), and Tri XFP (OS 192, 10G Fibre Channel, 10 GbE)
      • Boards work on a number of operating systems, including Windows, Linux, Solaris, IRIX, ALTIX, and VxWorks [...]
    • WILDSTAR 6/AMC
      One Virtex 6 FPGA per board with FPGA sizes up to LX550T or SX475T. Memory options of either up to 2.5 GBytes DDR3 DRAM for 16 GB/s or up to 64 MBytes DDRII+ or QDRII SRAM for 12.6 GB/s. Up to 549K logic cells and 907K multiplier bits per board. Air Cooled Only. (+)

      Features:

      293452569861964237.jpg
      • One Virtexâ„¢ 6 FPGA Processing Element
      • Up to 2.6 GB DDR2 DRAM in 5 Memory Banks for FPGA on Board or Up to 2.6 GB DDR3 DRAM in 5 Memory Banks for FPGA on Board or Up to 64 MB DDRII+ or QDRII SRAM in 4 Memory Banks for FPGA on Board
      • On Board Host Freescale P1020 or P2020 PowerPC
    • WILDSTAR 5 for PCI Express with Xilinx Virtex 5
      Up to three Xilinx Virtex-5 FPGA I/O processing elements – LX110T, LX220T, LX330T, or FXT Up to 7 GB DDR2 DRAM in 12 memory banks per board or up to 2 GB DDR2 DRAM in two memory banks and up to 40 MB DDRII, QDRII SRAM, or up to 1.4 GB RLDRAM (+)

      Features:

      36017.jpg
      • Programmable flash for each FPGA to store FPGA image
      • 8x PCI Express bus
      • High-speed DMA multichannel PCI controller
    • WILDSTAR 6 PCIe
      Up to three Xilinx Virtex-6 FPGA I/O processing elements - LX240T, LX365T, LX550T, SX315T, or SX475T (+)

      Features:

      46784.jpg
      • Up to 8 GBytes DDR2 DRAM or DDR3 DRAM in 14 memory banks per WILDSTAR 6 for PCI Express board or up to 480 MBytes DDRII+/QDRII DRAM in 15 memory banks
      • Programmable FLASH for each FPGA to store FPGA images
      • 8X PCI Express Bus Gen 1 or Gen 2
  • Creative Electronic Systems  (7)
    • GPIO-8439
      The latest family of CES general-purpose user-programmable I/Os (GPIO) is based on PMCs or XMCs, which are equipped with large FPGAs (+)

      Features:

      45644.jpg
      • The main feature of these boards is the Xilinx Virtex-6 FPGA, which is connected to the PCI and CES high-speed serial links, as well as with all required external memory sub-systems, including an ultra-high-speed staging buffer
      • CES GPIOs can be integrated on CES VPX, VME or CompactPCI processor boards, creating a very powerful user-programmable assembly
      • CES provides a complete FPGA programming environment, which allows users to develop their own applications and to interconnect with all of the hardware functionalities of CES boards
    • GPIO 8405
      A general purpose I/O PMC mezzanine (+)

      Features:

      • Application-specific FPGA
      • Electrical adaptation logic area
      • 64 I/O + 4 handshake from the panel and 64 I/O from P2
    • GPIO-E 8405
      A general purpose I/O PMC mezzanine (+)

      Features:

      • Application-specific FPGA
      • Electrical adaptation logic area
      • 64 I/O + 4 handshake from the panel and 64 I/O from P2
    • GPIO-8439
      User-Programmable I/O PMC / XMC (+)

      Features:

      46708.jpg
      • PMC (with XMC connector) or XMC (VITA 42)
      • Xilinx Virtex-6 LX130T / LX195T / LX240T / LX365T / SX315T / SX475T FPGA
      • One PCIe x8 on primary XMC
    • MFCC 8446
      Intelligent interface in a PMC form factor (CCPMC compliant) (+)

      Features:

      • Contains all of the required elements for ultra high-speed acquisition and processing applications
      • PowerPC 750CXe at up to 600 MHz with 256 KB internal L2 cache at full CPU speed
      • User-programmable, front-end,acquisition, low-power Xilinx VirtexE 400 KGates FPGA
    • RIO6-8096
      RIO6 family of 6U VME64x single board computers featuring the Freescale® QorIQ® P2010 (single core) or P2020 (dual core) processor, with an optional user-programmable Xilinx Spartan®-6 FPGA. The RIO6-8096 provides a PCIe x4 link over the standard VME-P0 connector on any existing VME64x backplane. (+)

      Features:

      229600090564847107.jpg
      • 6U VME64x form-factor
      • Freescale® QorIQ® P2010/P2020 processor
      • Xilinx Spartan-6 LX100T user-programmable FPGA (optional)
    • FIOV-2310
      3U OpenVPX FPGA Signal Processing board with a Xilinx Kintex-7 325T/410T user-programmable FPGA at its core. (+)

      Features:

      9911883.jpg
      • 3U OpenVPX form-factor (VITA 65)
      • Xilinx Kintex-7 325T/410T user-programmable FPGA
      • FMC HPC site for I/O customization
  • QinetiQ  (10)
    • Quixilica Callisto VXS-1
      High performance FPGA Based Communications management and processing platform (+)

      Features:

      • Fits in Switch card position in a VXS (VITA41.0) backplane
      • Supports 4X, full Duplex 3.125 GBps high speed serial links to up to sixteen VXS Payload slots
      • Front panel breakout of up to twelve 2.5 GBps links through fibre or copper SFP Transceivers
    • Quixilica Floating-Point QR Processor Core
      Scalable QR decompositon core for Xilinix Virtex and Virtex-II family FPGAs (+)

      Features:

      • Implements QR decomompositon for solving a wide range of least-means-square problems
      • Input matrix size can be configured
      • Supports complex or real data
    • Quixilica Venus VXS-1
      6U VXS card combines five high-resolution analog-to-digital channels with FPGA-based signal processing (+)

      Features:

      • 5x 14 bit 105 Msps AD6645 digitizers
      • Xilinx XC2VP70 FPGA
      • VME/VXS form factor
    • Quixilica Janus VXS-1
      10 Channel 160/400 MSPS Digital to Analog Converter and Xilinx Virtex-II Pro FPGA Processing Engine (+)

      Features:

      • 10 Channel DAC using 5x 16 bit Dual Channel 200 Msps AD9777 TxDAC
      • Xilinx XC2VP70 FPGA
      • VME/VXS form factor, VITA 41.0 Compliant, 8x 3.125 Gbps serial I/O links
    • Quixilica Neptune VXS-1
      2 Channel 2 GSPS Digitizer and Xilinx Virtex-II Pro FPGA Processing Engine (+)

      Features:

      20083.jpg
      • 2x 10bit 2Gsps Atmel ADC / DMUX
      • Xilinx XC2VP70 FPGA
      • VME/VXS form factor, VITA 41.0 Compliant, 8x 3.125 Gbps serial I/O links
    • Quixilica Mars VXS-1
      2 Channel 400MSPS Digitiser and Xilinx Virtex-II Pro FPGA Processing Engine (+)

      Features:

      • 2x 12bit 400 Msps Analog Devices AD 12400 ADC
      • Xilinx XC2VP70 FPGA
      • VME/VXS form factor, VITA 41.0 Compliant, 8x 3.125 Gbps serial I/O links
    • Quixilica Triton VXS-1
      Single Channel, 2 GSPS ADC/DAC and Xilinx Virtex-II Pro FPGA Processing Engine (+)

      Features:

      • 1x 10bit 2 Gsps Atmel ADC / DMUX
      • 1x 12 bit 2 Gsps Euvis MUX/DAC
      • Xilinx XC2VP70 FPGA
    • Quixilica Venus VXS-1 Plus
      5x 14 bit 125 Msps TI ADS5500 Digitisers (+)

      Features:

      • Xilinx XC2VP70 FPGA
      • VME/VXS form factor, VITA 41.0 Compliant, 8x 3.125 Gbps serial I/O links
      • 2x Front Panel SFP slots for 2.5Gbps fibre or copper transceivers
    • Quixilica Programmable Digital Radar Receiver
      Software programmable multi-channel digital radar receiver for Xilinx Virtex-II and Virtex-II PRO FPGA families (+)

      Features:

      • Programmble Quixilica FIR Filter Modules provide flexible filter chain
      • Optional Digital Down Conversion from fs/4 to baseband
      • Software programmable for filter configuration
    • Quixilica Floating Point FPGA Cores
      IEEE-754 compliant variable wordlength floating point artithmetic cores for Xilinx Virtex, Virtex E, and Virtex-II FPGA families (+)

      Features:

      • Includes IEEE-754 single and double precision wordlengths
      • Fully piplelined architecture
      • Supports Virtex, Virtex-E, and Virtex-II FPGA families
  • Altera Corporation  (8)
    • EP4SGX230
      40-nm FPGA (+)

      Features:

      • Up to 680K logic elements (LEs)
      • 2X bigger than Altera's Stratix III family
      • Altera 40-nm devices meet the diverse high-end application needs in a large number of markets such as wireless and wireline communications, military, broadcast, and ASIC prototyping
    • Stratix IV GT FPGAs
      Data rates from 155 Mbps to 11.3 Gbps (+)

      Features:

      • Transceivers operating at 11.3 Gbps
      • Optimized for 40G and 100G applications
      • Arria II GX FPGAs are the lowest power 3.75 Gbps transceiver FPGAs and are cost optimized for applications using mainstream protocols such as PCIe and GbE
    • Embedded HardCopy Blocks and 28 Gbps transceivers
      Provide a new partial reconfiguration method (+)

      Features:

      44581.jpg
      • Partial reconfiguration will improve logic density's effectiveness by allowing external memory storage of FPGA functions not presently needed
      • 28 Gbps embedded transceivers
      • 28 nm FPGAs
    • Cyclone III FPGAs
      Lowest power 65-nm FPGA (+)

      Features:

      • Manufactured using TSMC's 65-nm low-power (LP) process technology
      • Core static power as low as 35 mW at 25 ºC junction temperature
      • Unused I/O banks can be powered down via support for hot-socketing operation
    • Arria GX FPGA Family
      A transceiver-based FPGA ranging from 21,580 to 90,220 Logic Elements (LEs) (+)

      Features:

      33364.jpg
      • Up to 4.5 Mb memory, 12 transceivers
      • Supports two speeds of 1.25 and 2.5 Gbps
      • Utilizes PCIe (x1 and x4), GbE, and Serial RapidIO (1x and 4x) protocols
    • Nios II
      A family of 32-bit RISC embedded processors (+)

      Features:

      • More than 200 DMIPs
      • Low-cost FPGA implementation [...]
    • Cyclone II FPGA
      Industry's lowest-cost programmable logic platform for DSP implementation (+)

      Features:

      19241.jpg
      • Offers up to 68,416 LEs of logic density and 1.1 Mb of embedded memory
      • Delivers embedded configurable multipliers for low-cost DSP applications
      • Provides up to 150 18-bit x 18-bit multipliers operating at up to 250 MHz
    • Stratix II FPGA
      Extensive IP portfolio support (+)

      Features:

      19238.jpg
      • DSP blocks offer higher performance with multiplier, pipeline, and accumulate [something missing here?]
      • Offers more than 142 GMACS of DSP throughput using DSP blocks
      • Delivers 4x the DSP block bandwidth of Stratix devices – up to 370 MHz
  • Spectrum Signal Processing  (6)
    • PRO-3100
      A 6U, CompactPCI Virtex-II FPGA processing engine (+)

      Features:

      14186.jpg
      • Designed to interface to the TMI-3300 and PRO-3500 (PowerPC G4) boards
      • Four user-programmable Virtex-II FPGAs, each supporting up to six million gates
      • IBM 405GP PowerPC embedded controller
    • SDR-3000 SMRDP
      An "RF to Ethernet" wideband military communications (MILCOM) rapid-prototyping and development platform (+)

      Features:

      • Fully integrated, commercial-off-the-shelf (COTS) software defined radio platform
      • A “skinny” version of Spectrum's SDR-3000 MRDP providing a single-slot modem hardware solution
      • Integrates the latest Xilinx Virtex-4 Field Programmable Gate Array (FPGA) technology with Spectrum's proven MPC7410 PowerPC and TMS320C64x( digital signal processing technology
    • HCDR-1002
      A PowerPC-based high-channel-density receiver with FPGA-based channelization (+)

      Features:

      • Processes up to 26 MHz at 65 Msamples/sec
      • High-speed communications fabric based on the Solano Communications IC
      • Two 14-bit, 65 or 80 Msamples/sec analog-to-digital converters from Xilinx Virtex-E series FPGAs for channelization functions
    • ePMC-32MSDDC
      Eight Graychip GC4016 digital down converters support 32 narrowband or 8 wideband channels (+)

      Features:

      11701.jpg
      • Supports both wideband and narrowband signals
      • DDCs can be synchronized to provide coherent baseband signals
      • Two user-programmable Xilinx FPGAs for post-processing outputs from down converters
    • ePMC-8120
      A Xilinx Virtex-II FPGA processing engine (+)

      Features:

      15287.jpg
      • Single-width enhanced Processor Mezzanine Card (ePMC)
      • Incorporates a Xilinx XC2V6000 Virtex-II FPGA with 6 million system gates
      • 512 Mbytes of DDR SDRAM
    • PEM-FPGA
      A high-performance, programmable digital interface that connects Spectrum's ‘C6000-based DSP boards to custom and standard I/O systems (+)

      Features:

      • Provides up to 100 Mbits/sec of I/O bandwidth to each ‘C6000 DSP
      • Total data throughput of 200 Mbits/sec
      • Programmed to interface to virtually any type of digital I/O devices, including digital cameras, motor controllers, and as standard and custom parallel interfaces
  • First Silicon Solutions FS2  (1)
    • FPGAView for TLAs
      PC Windows-based program designed for use with Tektronix Logic Analyzers (+)

      Features:

      31713.jpg
      • Enables real-time debugging of Altera and Xilinx FPGAs
      • Design engineers can measure signals inside their FPGA design and select which group of internal signals to probe without having to recompile their design
      • Simplifies logic analyzer use by automatically updating channel names with the internal signal names selected and providing a mechanism to auto-select channel groupings from the same selection
  • PLDA  (3)
    • PCIe Gen 3 IP for ASIC, FPGA & SoC
      PLDA offers the most complete IP solutions for the PCIe interface with products designed to speed your time-to-design for ASIC, FPGA and SoC products. (+)

      Features:

      214683128961852862.jpg
      • XpressRICH3 PCIe 3.0 IP for ASIC: A highly configurable PCIe endpoint, root port, and switch semiconductor IP with support for PCIe 3.0 at Gen3, Gen2, Gen1 speeds, in x1, x2, x4, x8, x16.
      • XpressRICH3-AXI PCIe 3.0 IP with AXI for ASIC: A configurable PCIe Gen3 IP solution featuring an AXI3/AXI4 compliant user interface with built-in DMA.
      • QuickPCIe – PCIe with Enhanced DMA for FPGA: A flexible PCIe 3.0 interface IP with advanced DMA that exposes an AMBA AXI4 interface to the user. Targeted to Altera or Xilinx FPGAs.
    • PXIe XpressLite CY2
      Programmable boards and IP for PXI/CompactPCI Express system prototyping or product implementation (+)

      Features:

      32140.jpg
      • PXI Express x1 endpoint add-in board for CompactPCI Express systems
      • Altera Cyclone II based (EP2C50 standard configuration)
      • PLDA's IP Core PXIe x1 endpoint (low gate count)
    • SuperSpeed USB IP
      Provides embedded designers with the ability to integrate and prototype USB 3.0 functionality into their USB host or device designs (+)

      Features:

      • IP is delivered in clear, fully commented Verilog RTL source code
      • Includes free Bus Functional Model (BFM) with the IP which allows you to start designing immediately without the hassle of initially integrating a third-party verification IP
      • Comprehensive reference designs and state-of-the-art FPGA based prototyping boards available for easy initial hardware prototyping
  • Acromag, Inc.  (15 of 25)
    • VPX cards w/ config. Spartan-6/VIrtex-5
      3U VPX FPGA boards (+)

      Features:

      • Provide powerful and cost-effective solutions for high-speed processing of complex algorithms in embedded computing applications
      • Offers a choice of logic-optimized Xilinx Virtex-5 FPGAs while the VPX-SLX version employs a Spartan-6 FPGA with 150k logic cells. Virtex-5 FPGA cards deliver maximum computing performance
      • Spartan-6 FPGA cards are designed for cost-sensitive mid-level applications
    • VPX-VLX Series
      Series of 3U VPX FPGA boards (+)

      Features:

      52198.jpg
      • Configurable Xilinx Virtex-5 FPGA enhanced with multiple high-speed memory buffers and a high-throughput PCIe interface
      • Field I/O interfaces to the FPGA via the rear P2 connector and/or with optional front mezzanine plug-in I/O modules
      • Signal processor card that is capable of rapidly executing custom instruction sets and algorithms
    • VPX-VLX Series
      Series of 3U VPX FPGA boards (+)

      Features:

      51298.jpg
      • Configurable Xilinx Virtex-5 FPGA enhanced with multiple high-speed memory buffers and a high-throughput PCIe interface
      • Field I/O interfaces to the FPGA via the rear P2 connector and/or with optional front mezzanine plug-in I/O modules
      • Signal processor card that is capable of rapidly executing custom instruction sets and algorithms
    • XMC/PMC Virtex-5 FPGA Modules
      Acromag's PMC and XMC configurable FPGA modules are available with a choice of Xilinx Virtex-5 FPGAs optimized for logic, DSP, or co-processor applications (+)

      Features:

      46492.jpg
      • The boards are enhanced with multiple high-speed memory buffers and a high-throughput PCIe or PCI-X interface
      • Generous DDR2 SDRAM buffers store captured data prior to FPGA processing
      • Afterward, data is moved to dual-port SRAM for high-speed DMA transfer to the bus or CPU
    • XMC/PMC Virtex-5 FPGA Modules
      Acromag's PMC and XMC configurable FPGA modules are available with a choice of Xilinx Virtex-5 FPGAs optimized for logic, DSP, or co-processor applications (+)

      Features:

      45789.jpg
      • The boards are enhanced with multiple high-speed memory buffers and a high-throughput PCIe or PCI-X interface. Generous DDR2 SDRAM buffers store captured data prior to FPGA processing
      • Afterward, data is moved to dual-port SRAM for high-speed DMA transfer to the bus or CPU. Field I/O interfaces to the FPGA via the rear J4/P4 connector and/or with optional front mezzanine extension I/O modules
      • Also, take advantage of the conduction-cooled design or select an extended temperature version
    • PMC-AX1020/2020/3020
      Four 14-bit 20 MHz A/D and two 16-bit 900 kHz D/A (+)

      Features:

      • Customizable FPGA with up to 3 million system gates (Xilinx Virtex-II XC2V1000,XC2V2000,or XC2V3000)
      • FPGA code loads from PCI bus or Flash memory
      • 256K x 36-bit dual-ported memory
    • PMC-DX500/DX2000
      A line of reconfigurable FPGA PMC I/O modules (+)

      Features:

      17410.jpg
      • Cost/performance mix suitable for mid-level computing functions
      • Xilinx Virtex-II FPGAs with 500K (PMC-DX500) and 2M (PMC-DX2000) system gates
      • Up to 1 Mb of on-chip memory and 9 Mb of onboard SRAM
    • IP-EP200
      An industry pack digital I/O module (+)

      Features:

      32500.jpg
      • Implements a user-configurable Altera Cyclone II EP2C20 FPGA
      • Four models available: IP-EP201: 48 TTL I/O lines; IP-EP202: 24 differential RS485 I/O lines; IP-EP203: 24 TTL and 12 RS-485 I/O lines; IP-EP204: 24 LVDS I/O lines
      • FPGA programmable via JTAG port or IP bus
    • IP1K110
      Altera EP1K100 FPGA (+)

      Features:

      • Three models available: IP-1K110-0024: 24 differential EIA-485 lines, IP-1K110-2412: 24 TTL lines and 12 EIA-485, IP-1K110-4800: 48 TTL lines
      • FPGA programmable via the IP bus
      • Local static RAM (64K x 16) under FPGA control
    • IP-EP200 FPGA I/O
      Industry Pack digital I/O module with user-configurable Altera Cyclone II FPGA (+)

      Features:

      34855.jpg
      • Allows users to download custom instruction sets into the FPGA for adaptive computing applications
      • User-configurable Altera Cyclone II EP2C20 FPGA
      • Four models with 48 TTL I/O, 24 diff RS-485 I/O, 24 TTL and 12 RS-485 I/O, or 24 LVDS I/O
    • PMC-SLX
      PMC-SLX modules have user-configurable Xilinx Spartan-6 FPGA enhanced with high-speed memory and high-throughput PCI-X interface. Field I/O interfaces via front or rear connectors. (+)

      Features:

      184241139751472282.jpg
      • PMC Mezzanine Module
      • Reconfigurable Spartan-6 FPGA with 147,433 logic cells
      • PCI-X bus 100MHz 64-bit interface
    • PMC-LX/SX
      New PMC modules combine the power of a configurable Virtex-4 FPGA with interchangeable digital I/O front ends (+)

      Features:

      32206.jpg
      • Customizable FPGA with up to 60 K logic cells and 192 XtremeDSP slices
      • Supports both front and rear I/O
      • Plug-in I/O modules available for front mezzanine
    • XMC-VLX
      Acromag's XMC-VLX boards feature a reconfigurable Xilinx Virtex-5 FPGA enhanced with multiple high-speed memory buffers and a high-throughput PCIe interface (+)

      Features:

      • Field I/O interfaces
      • Reconfigurable Xilinx Virtex-5 FPGA
      • PCIe bus 4-lane Gen 1 interface
    • PMC-SX35
      User-configurable Virtex-4 FPGA module with plug-in I/O (+)

      Features:

      • Customizable FPGA (Xilinx Virtex-4 XC4VSX35) withup to 34 K logic cells and 192 XtremeDSP slices
      • Supports both front and rear I/O
      • Plug-in I/O modules are available for front mezzanine
    • PMC-LX40/LX60
      User-configurable Virtex-4 FPGA modules with plug-in I/O (+)

      Features:

      • Customizable FPGA (Xilinx Virtex-4 XC4VLX40/60) with up to 60 K logic cells and 64 XtremeDSPTM slices
      • Supports both front and rear I/O
      • Plug-in I/O modules are available for front mezzanine
  • Embedded Systems Design, Inc.  (1)
    • StreamBlade Family
      FPGA based platforms support development of combined software and reconfigurable hardware processing applications (+)

      Features:

      • Developers have full access to configured FPGAs and general purpose processors
      • GbE ports, utilizing hard core MACs allow for the implementation of distributed FPGA processing nodes
      • Ethernet connectivity provides network based command, control, and status
  • Altium Limited  (3)
    • Protel
      A complete board-level and FPGA-level design solution in a single application (+)

      Features:

      • Fully supports the design of FPGAs and their integration onto the PCB
      • Based on LiveDesign-enabled DXP platform to provide seamless integration with other Altium design systems
      • Hierarchical, multi-channel schematic editing environment
    • NanoBoard NB1
      An FPGA-based, nano-level breadboard (+)

      Features:

      • LiveDesign-enabled development board
      • Fully compatible with Altium's LiveDesign-enabled tools
      • Allows rapid and interactive implementation and debugging of FPGA designs
    • Nexar
      A comprehensive, vendor-independent electronic design solution for building complete processor-based digital systems based on FPGAs, using existing board-level design methodologies (+)

      Features:

      • Integrated hardware and software development tools, including soft IP cores and a LiveDesign-enabled development board
      • FPGA vendor-independent design
      • No HDLs required
  • CommAgility  (3)
    • AMC-V7-2C6678
      The AMC-V7-2C6678 is a high performance DSP/FPGA card. It is powered by the latest Texas Instruments TMS320C6678 multicore DSPs plus a Xilinx Virtex-7 FPGA. The module also provides fast, flexible I/O including Serial RapidIO (SRIO), Gigabit Ethernet and PCI Express. It is ideal for a range of high performance DSP/FPGA processing applications including telecoms and image processing. The AMC-V7-2C6678 includes a high density XC7VX415T-2 Virtex-7 FPGA as standard, with other FPGA options available on request. Virtex-7 FPGAs provide high DSP performance and I/O bandwidth, with best-in-class total power consumption that is 50% less than the previous generation. The board includes a single front panel SFP+ optical interface that links directly to the FPGA, plus a single mini-SAS connector linked to the SRIO switch. Should applications require timing and synchronisation, this is achieved via the front panel or backplane clock I/O, enabling the module to sync easily to other equipment. Should modifications be required to make this product fit your OEM requirements, CommAgility can support your needs through customisation or providing additional software and firmware FEATURES: 2 Texas Instruments TMS320C6678 DSPs each with 8 1.25GHz C66x cores Xilinx Virtex-7 VX415T FPGA Front panel SFP+ socket connected directly to FPGA Front panel mini-SAS connector with 25 Gbaud SRIO from on-board switch Gen2 RapidIO infrastructure between DSPs, FPGA, front panel and AMC.4 Full Gigabit Ethernet infrastructure Single width, full-size AMC card [...] (+)

      Features:

    • AMC-2C6678
      The AMC-2C6678 is a high performance signal processing AMC card with 16 DSP cores and FPGA resources. It is powered by the latest Texas Instruments TMS320C6678 DSPs plus a Xilinx Virtex-6 FPGA. It is ideal for a range of high performance DSP/FPGA processing appli-cations including telecoms and image processing. An IDT CPS-1848 Gen2 SRIO switch provides a 20Gbps per port Serial RapidIO infrastructure. Now with 1.2GHz DSPs each with 1GB SDRAM. (+)

      Features:

      182331908939722149.jpg
      • [...]
    • AMC-V6
      AMC-V6 FPGA AMC card for wireless baseband solutions including WiMAX and LTE (+)

      Features:

      46682.jpg
      • Xilinx Virtex-6 FPGA, either LX240T or LX550T
      • Three SFP+ sockets to support a CPRI or OBSAI antenna interface
      • 20 Gbps Gen2 RapidIO infrastructure from FPGA to AMC.4 backplane and front panel
  • Lavacore  (1)
  • Parsec  (2)
    • PM431
      A PMC module that employs FPGA technology to provide a high bandwidth processing platform targeted at typical Radar/Video functions such as FFT, FIR filters, and convolution (+)

      Features:

      41445.jpg
      • FPGAs: High speed DSP processing in ALTERA Stratix FPGA; EP1S25C6 Processing FPGA (standard) to EP1S40 ; onboard non-volatile storage of FPGA configuration data; Two banks of Processing FPGA configuration data provided; automatic configuration of FPGAs after power-up
      • Memory: standard: 5 x 256K x 36 ZBT memories (5 MB); Optional: 5 x 512K x 36 ZBT memories (10 MB)
      • PCI Interface:
    • PM430: Dual FPGA PMC
      Two Altera Stratix EP1S25 processing FPGAs, upgradable to EP1S40 devices (+)

      Features:

      20531.jpg
      • Two 32/64-bit 33/66MHz PCI-to-local-bus bridges supporting target read/write and DMA transactions
      • Separate target and DMA buses provide simultaneous data transfer in both directions
      • Single PMC version with one processing FPGA also available, such as PM431
  • Nu Horizons Electronics Corp.  (2)
    • FPGA Development Board
      Based on the Xilinx Spartan-3, one million gate FPGA (XC3S1500, XC3S2000) (+)

      Features:

      • 2 -1M X 16 X 4 SDRAM -16MB (Footprint for 2M X 18 SSRAM provided)
      • 32 Mb ST Flash ST M29W320DB
      • High-speed CAN 2.0B Phy interface ST L9616
    • TB-4V-FX60-PRO
      Inrevium Virtex-4 PowerPC processor development board (+)

      Features:

      • An ideal PCI-based platform for embedded system development using an Xilinx Virtex-4 FX60 FPGA with two built-in IBM PowerPC 405 Microprocessors
      • Availability of large FPGA size, flexible memory, and other resources provide an ideal design environment for hardware and software developments
      • Can be used either as a PCI-based card or stand alone [...]
  • DRS Technologies  (3)
    • Chameleon VMEbus
      A family of reconfigurable VMEbus I/O boards (+)

      Features:

      • 6U VME64X with up to 133 MHz bus rate and up to 266 MHz FPGA rate
      • Xilinx Virtex processors (XCV1000E to XCV2000E, up to four FPGAs per board)
      • Supports up to three PMC (64 bit / 66 MHz) mezzanine sites
    • Chameleon VME
      A reconfigurable processor board (+)

      Features:

      • Four Xilinx Virtex-1000E FPGAs
      • Up to 56 Mbytes of SRAM
      • Up to 128 Mbits of configurable memory
    • Chameleon cPCI
      A family of reconfigurable CompactPCI I/O boards (+)

      Features:

      • 6U CompactPCI boards
      • 66 MHz/64-bit
      • Three PMC mezzanine sites
  • Hunt Engineering  (15 of 17)
    • RTG001
      USB Connected Fast Data Acquisition & FPGA Processing System (+)

      Features:

      25246.jpg
      • User programmable Xilinx XC2V1500-6 FPGA (optionally 3M gates, at additional cost)
      • 2 channels of 210 MHz 12 bit A/D
      • 2 single-ended (optionally differential) channels of 160 MHz 16 bit D/A
    • HERON-IO2
      A FPGA module with Virtex II 1M gates plus two channels of 12-bit 125 MHz A/D and two channels of 14-bit 125 MHz D/A (+)

      Features:

      14193.jpg
      • Analog serial bandwidth of 500 MHz in and 145 MHz out
      • When fitted to a HERON module carrier, can have its FPGA “program” downloaded from the PC over the HERON serial bus, allowing users to program and reprogram the FPGA
      • I/P available for commonly used functions
    • RTG003
      USB-connected Software-Defined Digital Radio system (+)

      Features:

      30730.jpg
      • User programmable Xilinx XC2V1000-4 FPGA
      • Two channels of 125 MHz 12-bit A/D
      • Two channels of single-ended 125 MHz 14 bit D/A
    • RTG002
      A self-contained, programmable, digital I/O and FPGA system (+)

      Features:

      30408.jpg
      • Can be used as a standalone or connected to a PC via the USB 2.0 connection
      • User-programmable Xilinx XC2V1000-4 FPGA
      • 90 bits programmable single ended/differential digital I/O
    • Ready-to-Go System
      A ready-for-use low-cost system including USB-connected programmable FPGA and DSP hardware (+)

      Features:

      25307.jpg
      • Includes USB-connected FPGA/DSP hardware of the user's choice, USB cable, I/O cables to interface to peripherals, main power supply unit, and CD containing software tools, examples, and documentation
      • Connects to PCs using high-speed USB
      • Allows users to download FPGA designs, then exchange data between the FPGA and PC at speeds up to 40 Mbps
    • HERON-IO5-DO module with FPGA, ADC, DAC
      Module with Virtex-II FPGA, 1.5/3M gates (+)

      Features:

      22773.jpg
      • FPGA configuration downloaded using the HERON serial bus
      • Two 210MSPS 12-bit A/Ds connected to the FPGA
      • Two 160MSPS 16-bit D/As (with choice of single ended or differential outputs) connected to the FPGA
    • HERON-FPGA4V
      A FPGA module with digital I/O (+)

      Features:

      14191.jpg
      • Choice of 3M, 6M, or 8M gates Virtex-II FPGA
      • 90 user defined digital I/Os
      • Can be used to process data flows or as a flexible digital I/O module
    • HERON-FPGA12
      HERON module with Virtex-4FX12 FPGA plus DDR SDRAM, flash memory, and 60 bits digital I/O (+)

      Features:

      30063.jpg
      • Xilinx XC4FX12 Virtex-4 FPGA with embedded PowerPC
      • 128 MB DDR SDRAM connected as 32M x 32 at 200 MHz
      • 16 MB flash memory for PowerPC code storage
    • HERON-FPGA3
      A FPGA module with digital I/O (+)

      Features:

      14192.jpg
      • Virtex-II with 1M gates
      • 90 user defined digital I/Os
      • Can be used to process data flows or as a flexible digital I/O module
    • HERON-FPGA14
      HERON-FPGA14 Virtex-4 module (+)

      Features:

      • Module with XC4VLX60 or XC4VSX35 Virtex-4 FPGA plus 128 MBDDR SDRAM and 180 bits Digital I/O
      • 128 MB DDR SDRAM connected as 32Mx32 @ 200 MHz
      • FPGA configuration downloaded using the HERON Serial Bus
    • RTG004
      A USB-connected embedded PowerPC system (+)

      Features:

      30411.jpg
      • User-programmable Xilinx XC2VP7 FPGA with embedded PowerPC
      • 256 Mb of DDR SDRAM connected as two banks of 32 Mx32 @ 200 MHz
      • 16 Mb of flash memory for PowerPC code storage
    • RTG005
      A self-contained Image Processing system with a CameraLink base connection for image capture from camera (+)

      Features:

      • User programmable Xilinx XC4VFX12 FPGA with embedded PowerPC
      • 128 MB of DDR SDRAM connected as 32Mx32 @ 200 MHz
      • 16 MB of flash memory for PowerPC code storage
    • RTG006
      USB connected Virtex-4 FX system (+)

      Features:

      31909.jpg
      • User programmable Xilinx XC4VFX12 FPGA with embedded PowerPC
      • 128 MB DDR SDRAM connected as 32Mx32 @ 200 MHz
      • 16 MB of flash memory for PowerPC code storage
    • Hunt DSP Systems
      Choice of Xilinx FPGA and TI 'C6x modules with external memory and I/O options (+)

      Features:

      • Can be used in a PC, USB connected or standalone
      • Real-time data exchange between modules
      • Systems are programmable and reconfigurable
    • HERON-FPGA5
      A HERON FPGA module with SDRAM and digital I/O (+)

      Features:

      16598.jpg
      • Xilinx Virtex II FPGA with 1M gates
      • 256 MB of SDRAM connected as 64 Mbits x 32 at 133 MHz
      • FPGA configuration downloaded using the HERON serial bus
  • Technobox  (1)
    • 7757
      An advanced FPGA-based module for configurable digital I/O that offers in the XMC form factor many of the features and functions of the long-running Technboox P/Ns 2674 and 4289. The standard assembly employs an Altera Cyclone FPGA (5CGXFC4C6F27I7N) and features 32 general-purpose RS422/RS485 driven digital I/Os wired to the front panel and PN4 connector. The 32-bit data bus is shared by the FPGA and interfaced devices. SRAM (256K x 32b) is accessible from the FPGAS and PCIe interface. SRAM address is driven by FPGA outputs, allowing a variety of SRAM architectures. (+)

      Features:

      324884813334770097.jpg
      • 32-Channel general purpose digital I/O -- RS422 and RS485
      • Front and rear I/O with flexible termination
      • Separate direction control for each RS485 channel
  • Alpha Data  (4)
    • ADM-XRC-7V1
      The ADM-XRC-7V1 is a high performance reconfigurable XMC based on the Xilinx Virtex-7 range of Platform FPGAs. Features include PCI Express Gen2 interface, external memory, high density I/O, system monitoring and flash boot facilities. Placing the PCI Express bridge in bypass allows the creation of a Gen 2 x8 PCI Express endpoint design directly into the target FPGA (x8 for -2/-3 devices only x4 for -1 devices). The optional fitting of the Pn4 connector provides an additional 64 General Purpose IO (GPIO) links to the carrier card. (+)

      Features:

      210860547832477659.jpg
      • Features Xilinx Virtex-7 FPGA
      • High-performance reconfigurable XMC
      • PCI Express Gen2 interface
    • ADM-XRC-4
      FPGA-based PCI mezzanine card (+)

      Features:

      • FPGA: Xilinx Virtex-4 SX55 and LX60 to LX160
      • SRAM: Four or six banks of 72 Mb ZBT
      • Host interface: PMC, PCI, CompactPCI, and VME
    • ADM-XRC-II/II Pro
      A set of Xilinx Virtex-ii and Virtex-II Pro based FPGA processor PMCs (+)

      Features:

      • Support for the largest Xilinx devices from 2V1000 to 2V10000 and 2VP4 and 2VP50
      • Up to six banks of 512K x 36-bit ZBT SRAM
      • 384 Mbytes of DDR SDRAM
    • ADM-XP
      FPGA: Xilinx Virtex-II Pro XC2VP70 to XC2VP125 (+)

      Features:

      19176.jpg
      • DRAM: 2 banks x 16M x 64 DDR SDRAM
      • SRAM: 4 banks x 1M x 36 DDR SSRAM
      • Host interface: PMC, PMC-X, PCI, PCI-X, CompactPCI, and VME
  • XILINX, Inc.  (15 of 24)
    • Virtex-6 FPGAs
      Virtex-6 LXT FPGAs for high-performance logic, DSP, and serial connectivity with up to 36 low-power 6.5Gbps GTX transceivers and 864 DSP slices at 600 MHz (+)

      Features:

      42972.jpg
      • Virtex-6 SXT FPGAs for ultra high-performance DSP and serial connectivity with up to 36 low-power 6.5Gbps GTX transceivers and 2,016 DSP slices at 600 MHz
      • Virtex-6 HXT FPGAs for highest bandwidth with over 1Tbps connectivity from up to 720 SelectIO™ pins and 72 multi-rate transceivers, including GTH transceivers delivering line rates in excess of 11Gbps
      • Design out of the box with the Virtex-6 FPGA Evaluation Kit [...]
    • PicoBlaze
      The Xilinx PicoBlaze is a compact, capable, and cost-effective fully embedded 8-bit RISC microcontroller core optimized for the Xilinx Spartan™-3, Virtex™-II, Virtex-II Pro™ and Virtex-4 FPGAs and CoolRunner™-II CPLDs (+)

      Features:

      • Predictable performance, always two clock cycles per instruction, up to 200 MHz or 100 MIPS in a Virtex-4™ FPGA and 88 MHz or 44 MIPS in a Spartan-3 FPGA
      • 16 byte-wide general-purpose data registers
      • 1K instructions of programmable on-chip program store, automatically loaded during FPGA configuration
    • VIRTEX-4 FX60
      90 nm FPGAs (+)

      Features:

      • Support all major serial standards including PCI Express, Serial RapidIO, Ethernet, and Fibre Channel
      • Integrated 622 Mbps – 10.3125 Gbps serial transceivers [...]
    • XtremeDSP Development Tools
      Model and design your system using MATLAB, Simulink, and blocksets from The MathWorks (+)

      Features:

      31771.jpg
      • Use the Xilinx bit and cycle accurate library for designing algorithms for the FPGA
      • Import MATLAB algorithms like linear algebra and matrix inversion and multiplication
      • Automatically generate HDL or a bitstream at the push of a button with no loss in performance over designs written in HDL
    • Xilinx ISE Design Suite 12
      ISE Design Suite 12 software unlocks greater design productivity with breakthrough technologies for power optimization and cost (+)

      Features:

      • The Design Suite enables the fastest time to design completion with Xilinx Targeted Design Platforms – available in four configurations aligned to user-preferred methodology logic, embedded, DSP, or system design
      • Xilinx Targeted Design Platforms provide embedded, DSP, and hardware designers with access to an array of devices supported by open standards, common design flows, IP, and runtime platforms
      • The ISE Design Suite offers domain-specific design environments and enables designers to meet power and performance goals with Xilinx CPLDs and FPGAs, including the new Virtex-6 and Spartan-6 families
    • FPGAs for DSP
      Virtex-4 FPGAs for highest performance DSP (+)

      Features:

      • Up to 512, 500 MHz
      • XtremeDSP Slices (18 x 18 multiply, 48-bit add)\
      • Virtex-4 for lowest power per channel – each XtremeDSP Slice consumes only 2.3 mW per 100 MHz
    • XtremeDSP Devices
      The Xilinx XtremeDSP initiative helps you develop tailored high performance DSP solutions for aerospace and defense, digital communications, multimedia, video, and imaging industries. (+)

      Features:

      33609.jpg
      • High-performance configurable FPGAs for DSP designs
      • Development boards and Intellectual Property (IP)
      • System Generator and AccelDSP design and development tools
    • Virtex-5 LX FPGA
      Industry's First 65nm FPGA (+)

      Features:

      • ExpressFabric™ technology allow designs to be packed more efficiently
      • 330,000 logic cells
      • 1200 user I/Os
    • Avnet Virtex-6 FPGA DSP Kit
      Wireless, aerospace and defense, instrumentation and medical imaging applications continue to drive demanding performance requirements for today's sophisticated electronic systems (+)

      Features:

      46504.jpg
      • Due to their inherent hardware structure advantages, Xilinx FPGAs outstrip the high-end computing power of traditional digital signal processors
      • Based on the performance leading Virtex-6 FPGAs, this DSP Kit bundles pre-validated software tools, IP and hardware into a platform that addresses even the most challenging applications
      • With the addition of targeted reference designs, the Virtex-6 FPGA DSP kit enables users to focus on creating their own unique differentiation from the very beginning of the product development process, accelerating development for experienced users while also simplifying the adoption of FPGAs for new users
    • Xilinx Spartan-6 FPGAs
      Cost-effective alternative to ASICs with the performance and flexibility to meet changing system requirements (+)

      Features:

      42976.jpg
      • Spartan-6 LX FPGAs for absolute lowest cost with up to 150K logic density, 4.8Mb memory, integrated memory controllers, and up to 180 DSP blocks at 250 MHz
      • Spartan-6 LXT FPGAs for lowest risk, lowest cost serial connectivity with up to eight 3.125Gbps GTP transceivers
      • PCI Express Endpoint, and up to 180 DSP slices at 250 MHz
    • ISE Design Suite 10.1
      One integrated front-to-back FPGA IP catalog and design tool suite with unified interoperability (+)

      Features:

      • Domain specific design capture for DSP, embedded and logical design
      • Accelerated system development via customization and integrated libraries of optimized IP
      • Design tools optimized to minimize area while maximizing performance for Virtex-5 and Spartan-3 family Platform FPGAs
    • Virtex®-6 HXT FPGA
      Virtex®-6 HXT FPGA Optical Transport Network (OTN) Targeted Design Platform for supporting faster market implementation of 100G line cards (+)

      Features:

      47518.jpg
      • Virtex-6 HXT FPGAs offer the industry's highest serial bandwidth through a combination of 6.6 Gbps GTX transceivers and 11.18 Gbps GTH transceivers to enable next-generation packet and transport, switch fabric, video switching and imaging equipment
      • The devices are built on 40nm process using third-generation Xilinx ASMBL™ architecture and offer 15 percent higher performance and 50 percent lower power consumption as compared with competitive 40nm FPGA offerings
      • The devices operate on a 1.0v core voltage with an available 0.9v low-power option [...]
    • MicroBlaze
      32-bit RISC soft core optimized for implementation in Xilinx FPGAs (+)

      Features:

      • Thirty-two 32-bit general purpose registers
      • 32-bit instruction word with three operands and two addressing modes
      • 32-bit address bus
    • Avnet Spartan-6 FPGA DSP Kit
      Xilinx FPGAs exceed the computing power of DSPs with their inherent parallelism and offer co-processing methods of performance acceleration for signal processing (+)

      Features:

      46503.jpg
      • The Xilinx Spartan-6 FPGA DSP Kit integrates hardware, IP, software development tools and methodologies together into solutions that accelerate development for experienced users and simplify the adoption of FPGAs for new users
      • With the addition of targeted reference designs, these DSP platforms enable users to focus on creating their own unique differentiation from the very beginning of the product development process
      • This kit includes the Xilinx Spartan-6 LX150T board and allows users to quickly learn the different tool flows and design techniques involved in creating DSP centric designs with the Spartan-6 FPGA family
    • Virtex-6 FPGA DSP Kit
      Provides a platform for next generation products that include digital signal processing (DSP) which need to deliver more performance and flexibility with shorter development cycles and less cost and power (+)

      Features:

      44697.jpg
      • Out-of-the-box development solution that quickly builds confidence in developing DSP applications on FPGAs
      • Includes a Xilinx ML605 development board including a Virtex-6 LX240T FPGA, design tools, IP, reference designs, and documentation
      • Supports both traditional RTL and high-level design methodologies and can easily extended to include additional high-level design flows and I/O daughter cards through third party partners and standardized integration [...]
12/6/21 13:54
Close

Subscribe to Analog updates