DSP

Showing results for: radar signal processor
Refine DSP companies and products:
dsp digital signal processor digital signal processing dsp engine radar digital signal processing dsp software dsp hardware dsp system dsp systems radar signal processor digital signal processors discontinuous signal digital signal processin a/d d/a
Click on any vendor
to see a listing of
radar signal processor related products.
  • 4DSP  (7)
    • FM788 XMC
      The FM788 is a FPGA-based COTS card designed to deliver unparalleled performance for a variety of applications, including beamforming, direction finding, RADAR, and satellite communications. This XMC module is based on Xilinx's Virtex-7 and features eight 16-bit A/D channels running up to 250Msps each. Its design provides the largest channel count in this frequency range and the most available onboard memory for real-time buffering of large data vectors. (+)

      Features:

      284295382861546988.jpg
      • Virtex-7 XC7VX485T, XC7VX980T, XC7VX690T, XC7VX1140T
      • Eight-channel 16-bit 250MSPS A/D conversion
      • Available as air-cooled and conduction-cooled. Heat sink available for air-cooled applications.
    • FMC645
      The FMC645 is a Digital Signal Processor FMC daughter card based on the Texas Instruments TMS320C6455 device. The FMC645 daughter card is mechanically and electrically compliant with the FMC standard (ANSI/VITA 57.1). The card has a high-pin count connector and can be used in a conduction cooled environment. The card is equipped with power supply and temperature monitoring and offers several power-down modes to switch off unused functions and peripheral interfaces. Several Gigabit differential pairs from the FMC connector are used to implement a PCIe and Serial Rapid IO interface between the FMC and the carrier. Many other digital I/O interfaces are also made available to the FMC carrier. Because of the use of level translators between the DSP and the FMC connector the FMC645 can fully operate on any VITA 57.1 compliant carrier. A 512 MB DDR2 SDRAM on-board bank directly connects to the DSP thus providing the FMC645 with the memory resources required for demanding signal processing applications. (+)

      Features:

      212158754661410541.jpg
      • 1.2 GHz TMS320C6455 DSP
      • Fully conduction cooled compliant
      • VITA 57.1-2010 compliant
    • CES720
      The CES720 (Compact Embedded System) is a standalone, small form factor embedded system designed to provide a complete and generic processing platform for data acquisition, signal processing, and communication. The system features a low-power x86 CPU tightly coupled to a high-performance Kintex-7 and FPGA Mezzanine Card (FMC - VITA 57.1). The Kintex-7 410T FPGA provides a flexible and powerful processing backbone for interfacing to the FMC site, CPU, and external DDR3 SDRAM, with plenty of room left over for high-performance Digital Signal Processing needs. (+)

      Features:

      282556924091950899.jpg
      • System Controller - AMD G-Series Dual Core 1.0GHz Processor T40E
      • FPGA - Kintex-7 410T FFG676
      • 2GB DDR3 SDRAM
    • FM577
      The FM577 is a low-cost, low-power 65nm FPGA-based board available in the PMC form factor (+)

      Features:

      43451.jpg
      • High-speed DSP processing in Altera Cyclone III FPGA
      • FPGA A: EP3C40 or EP3C120
      • FPGA B: EP3C120 with to 288 embedded multipliers
    • FM680
      The first in a series of Xilinx Virtex-6 FPGA based XMC and PMC boards (+)

      Features:

      43927.jpg
      • Unique design and manufacturing technique provides advanced configurability called Board Level Advanced Scalable Technology (BLAST)
      • BLAST accelerates the manufacturing process for customer-specific configurations that normally delay the production cycle and add to production cost
      • Xilinx Virtex-6 provides more usable FPGA resources at substantially reduced power consumption and, therefore, generated heat
    • FM482
      Dual Xilinx Virtex-4 FPGA Signal Processor PMC/XMC (+)

      Features:

      43456.jpg
      • FPGA
      • High-speed DSP processing in Xilinx Virtex-4 FPGA
      • XC4VSX55, XC4VLX40, XC4VLX60, XC4VLX80, XC4VLX100 or XC4VLX160
    • FM485
      Dual FPGA Virtex-5 and Virtex-4 with 128 MB DDR2 and 16 MB of QDRII SDRAM Local Memory PMC-X and XMC for high-bandwidth analog conversion DSP processing (+)

      Features:

      43469.jpg
      • High-speed DSP processing in Xilinx Virtex-5 FPGA
      • XC5VLX50T, XC5VLX85T, XC5VLX110T, XC5VSX50T, or XC5VSX95T
      • Virtex-4 XC4VFX20 or XC4VFX60 with embedded PowerPC processor
  • AcQ InduCom  (6)
    • VME383
      A DSP DAC for high-speed analog signal regeneration and digital signal processing (+)

      Features:

      • 6U VMEbus board
      • Four TMS320C32 floating point DSPs running at 60 MHz, delivering 30 MIPS
      • Three high-speed 16-bit D/A channels per DSP
    • CPCI381
      A 3U CompactPCI board providing a powerful platform for high-speed analog signal capturing and digital signal processing (+)

      Features:

      11141.jpg
      • TMS320C32 floating point DSP, running at 60 MHz, delivering 30 MIPS
      • Two simultaneous sampling 12-bit A/D channels
      • Programmable sampling rate up to 7.5 Msamples/sec
    • VME381
      A DSP ADC for high-speed analog signal capturing and digital signal processing (+)

      Features:

      • 6U VMEbus board
      • Four TMS320C32 DSPs, each with 2 analog input channels, running at 60 MHz, delivering 30 MIPS
      • Two simultaneous sampling 12-bit A/D channels per DSP
    • M383 DSP M-module
      Provides a powerful platform for high-speed analog signal (re) generation and digital signal processing (+)

      Features:

      • Three analog output channels share the 10 MSps output update rate
      • Local software allows enhanced and user-specific signal processing
      • Eight general-purpose digital I/Os (4x input, 4x output, TTL-compatible) are available [...]
    • M381 DSP M-module
      Provides a powerful platform for high-speed analog signal capturing and digital signal processing (+)

      Features:

      • Two analog input channels are capable of simultaneously sampling at (maximum) 7.5 MSps sampling rate
      • Local software allows enhanced and user-specific signal processing
      • Gain and offset errors are compensated by the DSP
    • CPCI383
      A 3U CompactPCI board providing a powerful platform for high-speed analog signal (re)generation and digital signal processing (+)

      Features:

      11143.jpg
      • TMS320C32 floating point DSP, running at 60 MHz, delivering 30 MIPS
      • Three high-speed, 16-bit D/A channels
      • Analog output rate is software programmable up to 7.5 Msamples/sec (using DMA, single channel)
  • Aeroflex Laboratories, Inc.  (3)
    • BSA/BSG Families
      Broadband Signal and Environment Generator (BSG) and Broadband Signal Analyzer and Recorder (BSA) families (+)

      Features:

      19013.jpg
      • The BSG combines very high speed signal memory with depths up to 16 GB, high-performance D/A converters with sampling rates up to 1,300 MHz, and broadband RF up-converters
      • The BSA family combines broadband RF down-converters, wide-bandwidth high dynamic range A/D converters with sample rates to 1,500 MHz, and up to 16 GB of high-speed memory to record and analyze complex broadband signals and environments using DSP-based signal analysis software [...]
    • 3000 RF Modules
      RF Digitizers provide precision conversion of RF signals up to 6 GHz into digital sample data (+)

      Features:

      33857.jpg
      • Used with PXI Studio application software, provide class leading high Vector Signal Analysis of RF signals
      • A series of complimentary Digital RF signal generator modules provide complex modulated baseband and RF signals up to 6 GHz
      • The Aeroflex PXI studio application software provides a framework for vector signal analysis and generation within a single integrated user interface with a C API [...]
    • IQCreator™
      Designed for use with Aeroflex's digital RF signal generators, including the 3410 and PXI-based 3000 series, IQCreatorTM enables you to create waveform files that emulate digita (+)

      Features:

      • WiMAX
      • Generic Modulation
      • TDMA Digital Standards
  • Agilent Technologies  (6)
    • COTS VME/VXS Boards
      A new family of COTS VME/VXS (VITA 41 form factor) boards combining state-of-the-art Xilinx Virtex-4 SX and FX functionalities with advanced Acqiris data conversion technology (+)

      Features:

      32078.jpg
      • Incorporates Acqiris' JetSpeed II technology for clock generation and distribution
      • Feature two Xilinx Virtex-4 FPGAs, one SX55 targeted at digital signal processing and one FX100 for data flow control
      • Provides support for the VXS interface, two optical links on the front panel, a VME64x interface as well as DDR2 SDRAM memory and auxiliary analog and digital I/Os
    • E1430A
      2 pass, or subranging, 10 Msamples/sec ADC with 23 bits of resolution (+)

      Features:

      • A single-slot, single channel, C-size, VXI card that is a complete A/D module
      • Included in the module with the low distortion, low noise analog to digital converter, is flexible input signal conditioning, tunable digital filtering, an 8-Mbyte memory, and a high-speed local bus
      • Input signal conditioning includes 11 attenuation/gain ranges, AC/DC coupling and an analog anti-alias filter
    • PSA-80BW
      A wide-bandwidth, vector spectrum analyzer solution (+)

      Features:

      • Provides 80-MHz demodulation bandwidth and eight-second capture memory for multi-carrier power amplifier (MCPA), signal monitoring, radar, and satellite measurement applications
      • Up to 20 GHz frequency coverage, 0.1dB amplitude flatness, 0.7 degree phase flatness, and optional 1.2 Gbyte (768 Msamples) deep capture memory to provide eight seconds of full-bandwidth capture at the maximum sample rate
      • Well suited for error vector modulation (EVM)
    • U1065A - High-Speed cPCI Digitizers
      The front-end flexibility, coupled with astounding data conversion performance, makes this digitizer ideal for implementation in applications such as high-resolution radar and lidar, as well as semiconductor test and large scale physics research experiments (+)

      Features:

      41105.jpg
      • Quad-, dual- and single-channel 10-bit digitizers with up to 8 GS/s sampling rate
      • Choice of mezzanine front-ends with input protection, with up to 3 GHz analog bandwidth
      • Large acquisition memory from 256 kSample to 1 GSample (optional)
    • B4655A FPGA Dynamic Probe
      For visibility into FPGA´s internal activity (+)

      Features:

      • Up to 64 internal signals for each pin dedicated to debug
      • Ability to switch internal probe points in seconds
      • Maps internal signal naming from your FPGA design tool to your logic analyzer
    • Infiniimax 1130A
      A 1.5 GHz differential probe (+)

      Features:

      17118.jpg
      • Can be paired with Agilent's Infiniium Mixed Signal (MSO) and Digital Signal Oscilloscopes (DSO) for validating and verifying the performance of new high-speed digital product designs
      • Single-ended or differential measurements from a single probe amplifier
      • Controlled transmission-line probe heads provide a flat frequency response over the entire bandwidth specification and eliminate the distortion and loading that affects probes with in-band resonance
  • BeagleBoard  (1)
    • OMAP3 BeagleBoard
      Affordable, low-power, bring-your-own-peripherals computer based on a superscalar ARM processor, high-definition video capable general purpose DSP, and 3D graphics accelerator (+)

      Features:

      • ARM Cortex-A8 at 600 MHz, 1200 Dhrystone MIPS, and a roadmap to higher clock frequencies
      • C64x+ digital signal processor at 430 MHz capable of 720P video decode with a free C compiler for general purpose DSP programming
      • Imagination Technology PowerVR SGX 3D graphics processor capable of rendering over 10 million polygons per second and with a programmable pixel shader pipeline
  • CommAgility  (2)
    • AMC-D1F1-1200
      An AdvancedMC module that offers a compact, high-performance DSP/FPGA signal processing solution for AdvancedTCA and MicroTCA systems (+)

      Features:

      36707.jpg
      • Texas Instruments TMS320C6455 digital signal processor running at 1.2 GHz and a Virtex-4 FX100 FPGA from Xilinx
      • Optimized for applications requiring high-end signal I/O bandwidth in a compact mid-height AMC form factor, such as wireless baseband, image processing, defense, and aerospace
      • Provides a combination of DSP and FPGA resources, with fast and flexible links to external data and over 256 MB of onboard memory
    • AMC-D24AF4-RF2
      The AMC-D24AF4-RF2 is a highly integrated AdvancedMC (AMC) card with two wideband RF transceiver channels. The module’s main processor is the KeyStone™ II architecture-based TCI6638 digital signal processor (DSP)/ARM® SoC, which includes eight TMS320C66x+ DSP cores, as well as four ARM Cortex®-A15 cores for higher layer processing. The module also has two C6678 DSPs, plus a large Xilinx Kintex-7 FPGA. (+)

      Features:

      331528922051569331.jpg
      • Texas Instruments TCI6638 SoC DSP
      • Two Texas Instruments TMS320C6678 SoC DSPs
      • Two RF channels, each supporting FDD or TDD 662MHz - 3.84GHz
  • Compel Electronics  (2)
    • Coaxial adapters for monitoring points
      For the direct type, the device is made up of three coaxial interfaces so that an input / output path for the signal in transit and a direct link for monitoring are created (+)

      Features:

      30429.jpg
      • For the uncoupled type, the device is also made up of three coaxial interfaces; the difference lies in the fact that the signal which is picked up to be monitored is uncoupled with respect to the signal in transit through the insertion of an internal resistor which has been appropriately connected
      • Sometimes there is also the need for better adaptation, from an electrical point of view, of the output port of the signal being monitored; in this case a further resistor is appropriately connected, thus obtaining an uncoupled and adapted link
      • As far as the interface coaxial connectors are concerned, the most common types used are the 1.0/2.3 and 1.6/5.6 (male or female)
    • BALUNS
      Impedance adapters allow systems with different impedance levels to be connected (+)

      Features:

      30182.jpg
      • As is well known, the best method for transmitting a signal is to transport it using means with uniform impedance: Any variation or discontinuity leads to great reflections and losses in the signal
      • In modern equipment the need often arises to connect systems with a 75 ohm output (typical in the use of coaxial cables) with systems with a 120 ohm output (typical when using twisted pairs which have been introduced because a high density of connections with cables of reduced dimensions is needed)
      • It becomes necessary, therefore, to adopt a device capable of connecting the two systems in such a way that each uses its own impedance, eliminating the possibility of having substantial losses in the signal
  • Conduant Corporation  (1)
    • StreamStor SFPDP
      Serial FPDP mezzanine board for long distance, high speed, data capture (+)

      Features:

      • When combined with Conduant's StreamStor Amazon SATA disk controller, real time data input performance exceeds 500 MBps
      • Features four independent optical fiber interface ports for simultaneous data input and output available on each port
      • The StreamStor SFPDP board can support cable lengths up to 25 kilometers
  • CSP Inc. (CSPI) MultiComputer Division  (2)
    • 3220Q OpenVPX Intel Blade
      The 3220Q is a rugged high-performance 6U OpenVPX Blade, with a dual socket Intel® Xeon® processor and QuickPath Interconnect (QPI) to deliver superior performance-per-watt and low latency. Operating as a general purpose compute engine, it is one of the fundamental building blocks in the CSPI TeraXP family of Embedded Servers. The 3220Q supports Red Hat Enterprise MRG delivering real-time capabilities and high speed messaging in a commercial off the shelf (COTS) Linux based operating system. Featuring an Open Software Stack (OpenMPI/OFED, AMQP) and a Converged Fabric (supporting FDR InfiniBand, 10/40GbE, Fibre Channel) the TeraXP Embedded Servers provide the scalable processing power and I/O bandwidth needed for embedded military computing applications such as radar, sonar, digital signal processing, command and control, and ISR. Dual Socket Intel® Xeon® Processors: (+)

      Features:

      • 4 Cores/8 Threads per socket
      • 8 MB On-chip L3 Cache per socket
      • 2.13 GHz Core Clock
    • 3300GTX OpenVPX NVIDIA GPGPU Blade
      The 3300GTX provides CSPI’s TeraXP Embedded Servers with a high performance co-processor blade featuring many CUDA cores to accelerate parallel streaming and FFT based applications. (+)

      Features:

      • 6U OpenVPX GPGPU Co-processor Blade
      • One MXM site supporting a NVIDIA GTX 560M GPGPU
      • Implemented with the Mobile PCI Express Module (MXM) version 3.0 standard, capable of hosting newer GPGPUs as they become available
  • Curtiss-Wright  (15 of 20)
    • CHAMP-AV8
      Rugged, high performance OpenVPX DSP (digital signal processing) engine based on Intel next-generation quad-core processor technology (+)

      Features:

      46882.jpg
      • High-performance floating-point processing for digital signal processing
      • (DSP) and general purpose applications
      • 6U OpenVPX-compliant
    • VPX3-453 3U VPX Virtex-6/8640D DSP
      The VPX3-453 is a high performance, small form factor DSP engine that combines a Xilinx® Virtex®-6 FPGA and a Freescale® Power Architecture MPC8640D processor. This small form-factor 3U VPX (VITA 46/48) card is ideal for SWaP-constrained environments and is designed to support the full -40 + 85 deg C rugged operating temperature range. The VPX3-453 speeds and simplifies the integration of advanced DSP and image processing into embedded systems designed for demanding Radar Processing, Signal Intelligence, ISR, Image Processing, and Electronic Warfare applications. (+)

      Features:

      217438257121131374.jpg
      • One user-programmable Xilinx Virtex-6 FPGA node (LX240T)
      • One Dual-core Freescale Power Architecture MPC8640 processor
      • On-board Gen2 PCIe switch
    • FPE650 FPGA VPX
      A quad FPGA processor card which combines high bandwidth I/O, achieved through VPX/VPX-REDI and FMC/VITA 57 sites (+)

      Features:

      36805.jpg
      • Designed for the most demanding digital signal processing applications such as electronic counter measures, signal intelligence, and electro-optics
      • Four Xilinx LXT, SXT, or FXT Virtex-5 FPGAs
      • 4x Xilinx Virtex-5 FPGAs (SX95T, LX155T, FX100T)
    • CHAMP-WB 6U OpenVPX Virtex-7 FPGA Card
      The Curtiss-Wright CHAMP-WB is a user-programmable Xilinx Virtex-7 FPGA-based computing product designed to meet the needs of challenging embedded high-performance digital signal and image processing applications. The CHAMP-WB is targeted specifically at wide-band, low latency applications that require large FPGA processing, wide input/output requirements, with minimal latency. (+)

      Features:

      226605770407897699.jpg
      • OpenVPX (VITA 65) profile MOD6-PAY-4F1Q2U2T-12.2.1-11, VPX REDI (VITA 48 option)
      • Digital Signal Processor with Single user-programmable Xilinx Virtex-7 FPGAs (X690T or X980T)
      • 8 GB DDR3L SDRAM in two banks
    • ProWare PMC-440
      A rugged FPGA PMC card for the capture, processing, and output of data derived from high-speed sensors such as electro-optical/infrared (EO/IR) and radar systems (+)

      Features:

      20558.jpg
      • Onboard FPGA delivers up to 20 billion operations/sec performance for FFT and digital filter DSP functions
      • Can be configured with either of two versions of the Xilinx Virtex-II Pro FPGA: the XC2VP20 (9,280 logic slices/88 18x18 multipliers) or the XC2VP40 (19,392 logic slices/192 18x18 multipliers)
      • 64-bit, 66 MHz PCI interface with support for PCI-X
    • MPMC-9335 VPX COTS System
      The new MPMC-9335 is a 3-slot COTS rugged VPX system designed for easy and quick configuring to meet demanding requirements of defense, aerospace & law enforcement applications. This compact and lightweight small form factor system is ideal for space/weight/power (SWaP)-constrained platforms such as UAVs and ground vehicles. With its latest generation quad-core Intel Corei7 single board computer & 240-core NVIDIA Fermi GPGPU, the MPMC-9335 is well-suited for compute intensive applications such as image, data and radar processing. (+)

      Features:

      204732848407408525.jpg
      • 3U 3 slot integrated system
      • 9.3â€?L x 5.5â€?W x 4.9â€?H and 14.5 lbs (fully populated)
      • DEF-STAN 61-5 Part 6, Issue 6 28 (17.5-32) VDC input Power Supply
    • XF07-523 Kintex-7 FPGA XMC
      The XF07-523 provides direct FPGA driven LVDS I/O through the front panel and PMC/XMC connectors for rear I/O on a fully ruggedized XMC module designed to perform optimally in the harshest conditions including +85C card edge conduction-cooled solutions. This high performance module is ideal for use in a wide range of applications that require high-speed FPGA based digital I/O such as avionics, radar, digital imaging, and FPGA co-processor and other test equipment. (+)

      Features:

      212842378121582232.jpg
      • Based on Xilinx Kintex-7 325T (speed grade 2) FPGAs
      • High performance, high bandwidth LVDS digital I/O on front panel and rear IO
      • Dual x16 DDR3 memories for > 5 Gbytes/sec usable bandwidth
    • Embedded Video Processing System
      Curtiss-Wright combines its high performance octal-core Intel Xeon D signal processors and a NVIDIA Quadro Pascal GPGPU processor with Xilinx Kintex FPGA Frame Grabber flexibility to provide a compact versatile processing system for embedded video applications. The video processing system is packaged in our MPMC-9331 3-slot 3U OpenVPX rugged embedded system, a SWaP-optimized solution with flexibility to handle multiple graphics applications. (+)

      Features:

      3745773144055609214.jpg
      • Rugged Embedded Video Processing System designed for aerospace and defense applications
      • 2 x Intel Xeon D Octal Core DSPs
      • NVIDIA Quadro P5000 GPGPU
    • Radar Video Distribution Server
      A radar video distribution server in PCI, CompactPCI, and VME form factors (+)

      Features:

      15581.jpg
      • Cost-effective solution for the distribution of radar video from a sensor to multiple display consoles
      • Uses standard COTS Ethernet networks and proprietary digital compression technology to distribute video from a radar source to any number of display stations
      • Provides flexibility in the choice of where and when radar video is displayed
    • Cougar 2 Radar Input & Scan Conversion
      Cougar 2 is a high performance solution for capturing, converting and mixing radar video, available as a turnkey product ready for deployment. The single-slot VME modular Cougar 2 system provides the complete functionality required to integrate and implement a wide range of radar input/scan conversion configurations for demanding, embedded military applications. Users install the Cougar 2 into their system and attach radar, display and network interfaces, configuring, controlling and monitoring the system with the high-level RVL+ API. (+)

      Features:

      320757185221647710.jpg
      • Complete solution for radar video acquisition and scan conversion
      • Wide range of radar interfaces supported
      • Can be tailored to provide the optimal price/performance balance for a specific application [...]
    • Eagle-2 Hi-Res Radar Scan Converter PMC
      Eagle-2 is a high-performance radar scan converter from Curtiss-Wright Defense Solutions. Eagle-2 provides improved performance and support for high-resolution screen displays up to 2560 x 1600, including 2048 x 2048, making it the perfect choice for high-end radar display applications such as air traffic control (ATC) displays, VTS display command and control consoles, and radar head monitors. (+)

      Features:

      320758153221160628.jpg
      • Supports rotation rates of 90rpm at 2048 x 2048 display resolution
      • Field-proven White-Powell scan-conversion algorithms
      • Simultaneous scan-conversion of multiple radar sources
    • VPX3-534 3U VPX 6GSPS Tranceiver Card
      The VPX3-534 combines high-speed multi-channel analog IO, user programmable FPGA processing and local processing in a single 3U VPX slot for direct RF wideband processing to 6 Gsps. This card allows for a high performance single slot transceiver with two 6 Gsps 12bit channel, to over 6 GHz instantaneous analog bandwidth, but can also scale to larger system with many channel. The architecture is optimized for RADAR, Electronic Warfare (EW), Signal Intelligence (SIGINT), Radar Warning Receivers (RWR) and Software Defined Radio (SDR) applications. (+)

      Features:

      3928024634057507215.jpg
      • 3U VPX Analog I/O card with 2x 6Gsps/12b analog inputs (or 4x 3Gsps/12b)
      • Xilinx KU115 UltraScale user programmable FPGA
      • Xilinx ZU4 UltraScale+ Zynq
    • Cougar
      An Integrated Radar Input and Scan Converter VME board set (+)

      Features:

      41272.jpg
      • Provides an open standards-based, high-performance choice for capturing, converting, and mixing radar video
      • Designed for demanding military radar applications, Cougar speeds and simplifies the integration of advanced radar image processing and distribution functionality into deployed embedded system
      • Flexible, two-slot VME modular system
    • VPX3-535 3U VPX ADC DAC 6 GSPS
      The VPX3-535 combines high-speed multi-channel analog IO, VITA 48.8 Air-Flow Through (AFT) technology, user programmable FPGA processing and local processing in a single 3U VPX slot for direct RF wideband processing to 6Gsps. This card allows for a high performance single slot transceiver with two 6Gsps 12bit channel, to over 6GHz instantaneous analog bandwidth, but can also scale to larger system with many channel. The architecture is optimized for RADAR, Electronic Warfare (EW), Signal Intelligence (SIGINT), Radar Warning Receivers (RWR) & Software Defined Radio (SDR). (+)

      Features:

      • 3U VPX ADC DAC Card with Xilinx UltraScale FPGA
      • 2x 6Gsps/12b analog inputs (or 4x 3Gsps/12b)
      • 2x 6Gsps/12b analog outputs
    • CHAMP-FX4 6U OpenVPX Virtex-7
      The CHAMP-FX4 is the flagship 6U product in Curtiss-Wright Defense Solutions’ family of user programmable Xilinx® Virtex®-7 FPGA-based computing products, designed to meet the needs of challenging embedded high performance digital signal and image processing applications. Curtiss Wright’s 4th generation 6U FPGA card, the CHAMP FX4 combines the dense processing resources of three large Xilinx Virtex-7 FPGAs with over 12 GB of memory resources, all on a rugged 6U OpenVPX (VITA 65) form factor module. (+)

      Features:

      292163107861464693.jpg
      • Over 100 GB/s of backplane I/O bandwidth
      • Gen2 Serial RapidIO (SRIO) provides standards-based connectivity to general-purpose processing boards such as the VPX6-1957 and CHAMP-AV8
      • Two FMC interfaces with 80 differential signal pairs
  • ELMA Electronic  (1)
    • VPX-300 SystemPak
      The VPX-300 SystemPak is a reference development platform based on 3U VPX architecture (+)

      Features:

      52829.jpg
      • Designed around a Virtex-6 FPGA front end processor (FEP) card
      • Combining data and control plane topology, the architecture supports multi-processor capability via two clusters for front-end and back-end processing
      • The OpenVPXTM standard backplane profile has two separate star sections that are established through a data and control plane switch, handling both PCIe and GigE links
  • GE Intelligent Platforms, Inc.  (15 of 33)
    • AXISLib-CL
      AXISLib-CL Signal and Vector Processing Library providing digital signal processing and mathematical functions (+)

      Features:

      • Comprehensive signal and vector processing functionality
      • Accelerates engineering development
      • Both industry standard VSIPL and proprietary AXISLib0RSPL API provided
    • G4ADSP
      Rugged 6U VME Quad Processor addresses Radar, Sonar, Image Processing, and Communications Applications (+)

      Features:

      43935.jpg
      • Four Freescale MPC 7448 processors operating at up to 1.4 GHz
      • 2 GB of DDR memory
      • Four GbE channels and PCI on P0
    • AXISLib-CL
      A platform-independent linkable software Signal and Vector Processing Library (+)

      Features:

      41674.jpg
      • Software development can begin before target hardware is available · Rapid migration from modeling to embedded platform deployment
      • Designed for developers of military and aerospace applications such as radar, sonar, and SIGINT, but is also applicable to any industry – such as medical imaging – where rapid development of sophisticated digital signal- and image processing applications is a requirement
      • Works in conjunction with AXIS, GE Intelligent Platforms Advanced Multiprocessor Integrated Software development environment, designed to dramatically speed and simplify the creation and debugging of sophisticated DSP applications
    • ICS-1580
      FPGA DSP Board with high-speed Inputs in PMC format (+)

      Features:

      33574.jpg
      • Xilinx Virtex-II Pro FPGA with two on-chip PowerPC processor
      • Linux kernel pre-installed
      • 64 MB of SDRAM
    • G4DSP-XD3
      Massive signal and data processor (+)

      Features:

      36791.jpg
      • Four MPC7448 nodes at 1 GHz to 1.4 GHz
      • AccellerX PCI-X architecture
      • Up to 2 GB DDR SDRAM
    • AXISLib-GPU
      DSP/Math Library for NVIDIA Many-Core GPU Platforms (+)

      Features:

      • Optimize your performance with GE Intelligent Platforms' new AXISLib-GPU – a Signal and Vector Processing Library that supports the development and deployment of high-performance DSP and multiprocessing applications on GE's NVIDIA CUDA-enabled GPGPU (general purpose processing on a graphics processing unit) platforms
      • Typical applications include radar, sonar, image processing, signals intelligence and ISR (intelligence, surveillance, reconnaissance)
      • The AXISLib family of performance-optimized DSP and math libraries includes AXISLib for Power Architecture, our recently announced AXISLib-x86 for systems based on Intel processors as well as AXISLib-GPU, which can operate as stand-alone modules or within the AXIS Advanced Multiprocessor Integrated Software development environment [...]
    • GE Fanuc ICS-1556B
      ADC module (+)

      Features:

      42046.jpg
      • 400 MHz bandwidth
      • 14-bit ADC PMC Module
      • Designed for demanding communication applications such as software defined radio, signals intelligence (SIGINT), digital receivers, and tactical communications where the requirement is to convert analog data into digital information in as close to real-time as possible
    • ICS-8560
      The ICS-8560 is a XMC/PMC form factor digital transmitter module intended for Software Defined Radio (SDR) applications (+)

      Features:

      36709.jpg
      • 2 AC-coupled analog outputs, 16-bit resolution (Analog Devices AD9726)
      • FS ≤ 200 MHz (Single Data Rate Mode), Fs ≤ 400 MHz (Double Data Rate Mode)
      • Xilinx Virtex-4 FX60 or FC100 FPGA with multiple IP cores (incl.SDR 200 MHz, DDR 400 MHz)
    • ICS-1650
      High-speed data acquisition and DSP engine for PCI Express-based desktop PCs and servers deployed in SIGINT, communications, radar, medical imaging, and T&M applications (+)

      Features:

      38089.jpg
      • 4-channel, 250 MHz 12-bit ADC
      • Transformer-coupled inputs
      • 50 ohm input impedance
    • V4DSP
      A COTS FPGA multiprocessor designed for rugged defense and aerospace applications (+)

      Features:

      36792.jpg
      • Two Xilinx Virtex-4 FX100 FPGAs
      • QDR SRAM 2M x 36 bits
      • DDR2 SDRAM 2 banks 64M x 16 or 1 bank 64M x 32 bits per node
    • Tsumani 6U CPCI Development Kit
      FPGA processor solution targeted at high performance software defined radio applications (+)

      Features:

      • Dual Stratix EP1S80 FPGAs are tightly coupled to provide a power platform for signal processing
      • Two PMC module sites provide I/O connectivity to either front panel or back panel connections
      • A direct high bandwidth 1 GBps path from the PMC P4 connector directly to the FPGAs
    • DSP220
      The DSP220 is a 6U VXS (VITA 41.2) quad 8641/8641D multiprocessor (+)

      Features:

      36788.jpg
      • Featuring 4 single-or dual core Freescale PowerPC 8641 System-on-Chip nodes and a VITA 42.2-compliant XMC slot
      • Four Freescale MPC8641D processors
      • Eight banks DDR SDRAM, up to 8 GB total
    • TS-PMC A30
      FPGA processor solution targeted at high performance military and commercial computing applications (+)

      Features:

      20869.jpg
      • Stratix FPGA and high bandwidth capability PCI Mezzanine Card
      • Ideal for video and image processing, software defined radio, radar, sonar as well as other high performance signal processing applications
      • Flexibility of front or rear panel connections [...]
    • ICS-8554D
      For use in communications, radar, and test and measurement applications in harsh environments (+)

      Features:

      33318.jpg
      • Suitable applications include military communications, signal intelligence, smart antenna, radar beam forming, wireless test and measurement and satellite ground stations
      • DC-coupled digital receiver
      • Four 14-bit ADCs that sample synchronously at frequencies up to 105 MHz
    • ICS-1554
      4-channel, 160 MHz 16-bit ADC PMC module with Virtex-5 SX95 user programmable FPGA (+)

      Features:

      • Four AC-coupled analog inputs
      • FS < 160 MHz per channel
      • Xilinx Virtex-5 SX95 User Programmable FPGA
  • Innovative Integration  (15 of 21)
    • X6-250M
      The X6-250M integrates digitizing with signal processing on a PMC/XMC IO module. The module has a powerful Xilinx Virtex 6 FPGA signal processing core, and high performance PCI Express/PCI host interface. Applications include software-defined radio, RADAR receivers, and multi-channel data recorders. The X6-250M has eight simultaneously sampling A/D channels that sample at rates up to 250 MSPS (14-bit). The A/D have matched input delays and response. The A/D are supported by a programmable sample clock PLL and triggering that support multi-card synchronization for large scale systems. A Xilinx Virtex6 SX315T (LX240T and SX475T options) with 4 banks of 1GB DRAM provide a very high performance DSP core with over 2000 MACs (SX315T). The close integration of the analog IO, memory and host interface with the FPGA enables real-time signal processing at extremely high rates. FEATURES: Eight 250 MSPS, 14-bit A/D channels 1.5Vp-p, AC-Coupled, 50 ohm, SSMC inputs Xilinx Virtex6 SX315T/SX475T or LX240T 4 Banks of 1GB DRAM (4 GB total) Ultra-low jitter programmable clock Gen2 x8 PCI Express option providing 2 GB/s sustained transfer rates PCI 32-bit, 66 MHz with P4 to Host card PMC/XMC Module (75x150 mm) 18-22W typical Conduction Cooling per VITA 20 Ruggedization Levels for Wide Temperature Operation Adapters for VPX, Compact PCI, desktop PCI and cabled PCI Express systems [...] (+)

      Features:

    • Quixote 64-bit 6U
      A 64-bit CompactPCI 6U board for advanced signal capture, generation, and co-processing (+)

      Features:

      • 1 GHz TMS320C6416 DSP and 2 to 6 MGATE Virtex-II FPGA
      • 32 MB SDRAM, 8 MB ZBT SBSRAM and AD6645 and AD9764 converters
      • 64/32 bit CompactPCI, 66 MHz, 5 V/3.3 V and complex trigger modes with HW event logging
    • Quixote Complete SDR Solution
      1 GHz TMS320C6416 DSP (+)

      Features:

      22229.jpg
      • 2 to 6 MGATE Virtex-II FPGA
      • 32 MB SDRAM, 8 MB ZBT SBSRAM
      • AD6645 and AD9764 converters
    • X5-G12
      PCI Express XMC Module with Dual channel 1 GSPS, 12-bit Digitizer, Virtex5 FPGA and 512MB Memory. An excellent choice as a front-end digitizer (+)

      Features:

      • PCI Express XMC Module with Dual channel 1 GSPS, 12-bit Digitizer, Virtex5 FPGA and 512MB Memory an excellent choice as a front-end digitizer for RADAR or 3/G/4G wireless receivers
      • An XMC I/O module featuring dual channels of 1 GSPS 12-bit digitizing with a Virtex5 FPGA computing core, DRAM and SRAM memory, and eight lane PCI Express host interface
      • A Xilinx Virtex5 SX95T or LX155T with 512 MB DDR2 DRAM and 4MB QDR-II memory provides a very high performance DSP core for demanding applications such RADAR and direct RF digitizing
    • Quadia
      Quad-DSP (+)

      Features:

      34737.jpg
      • Dual FPGA
      • Dual PMC sites
      • CompactPCI board with an advanced architecture that provides inter-processor connectivity and access to external interfaces
    • FMC Family
      Innovative Integration's FMC Family offers a wide range of dense, high-performance I/O solutions in VITA57 form-factor. The FMC standard requires only the core I/O transceiver circuitry that connects directly to the FPGA on the carrier card.  The resulting efficiencies translate to substantial benefits. The FMC modules deliver a wide range of solutions:  High Speed digitizing Signal Generation for wireless Transceiver Pulse Generation, Medical Imaging, Precision Recording/Playback, RADAR, LTE WiMAX Physical Layer, Wireless Receiver and Transmitter, Remote Radio Head receiver, OBSAI and CPRI interface, Serial FPDP and SRIO fiber optic ports. FEATURES: High speed digitizing and signal generation FMC I/O modules FMC-1000 Module with 2x 1000 MSPS 14-bit A/D, 2x 1000 MSPS 16-bit DAC with PLL and Timing Controls FMC-500 Module with 2x 500 MSPS 16-bit A/D, 2x 1230 MSPS 16-bit or 1x 1GSPS DAC with PLL and Timing Controls FMC-310 Module with 4x 310 MSPS 16-bit A/D with PLL and Timing Controls FMC-250 FMC Module with 2x 250 MSPS 16-bit A/D, 2x 500 MSPS 16-bit or 1x 1GSPS DAC with PLL and Timing Controls FMC-SFP+ FMC Module with Four SFP+ Ports [...] (+)

      Features:

    • X6-1000
      X6-1000M integrates high-speed digitizing and signal generation with signal processing on a PMC/XMC IO module for demanding DSP applications. The tight coupling of the digitizing to the Virtex6 FPGA core realizes architectures for SDR, RADAR, and LIDAR front end sensor digitizing and processing. The PCI Express system interface sustains transfer rates over 2 GB/s for data recording and integration as part of a high performance realtime system. (+)

      Features:

      307375327861483711.jpg
      • Two 1 GSPS, 16-bit DAC channels and Two 1 GSPS, 12-bit A/D channels
      • +/-0.5V, AC or DC -Coupled, 50 ohm, SSMC inputs and outputs
      • Xilinx Virtex-6 SX315T/SX475T or LX240T
    • ePC-nano Rugged Embedded Computer 5.9" x 3" XMC IO
      The ePC-nano – a user-customizable, turnkey computer with full Windows/ Linux PC functionality to provide autonomous operation of a huge assortment of FPGA-accelerated, analog I/O-equipped XMC modules. The ePC-nano is a conduction-cooled solution, engineered to ruggedization level 3, for use in vehicles or other mobile applications. Distributed Data Acquisition: Put the ePC-nano at the data source and reduce system errors and complexity. Limitless flexibility – embellish FPGA signal processing or swap XMC module to alter functionality. XMC site for I/O, userprogrammable FPGA for real-time DSP, ethernet for WAN system connectivity, dual mSATA for long-duration data logging/signal playback, GPS/IEEE-1588 supporting synchronous operation over large distances, USB ports to allow connectivity to ubiquitous peripheral devices. Remote or Local Operation: Continuous data streaming up to 500 MB/s (local SSDs) or 1 Gb/s Ethernet. A dual, 10 GbE expansion module will be available soon. Rugged: Boots OS from embedded 16 GB eMMC drive in a compact, rugged 150x75mm footprint that is ready for deeply embedded operation in a rugged environment. Perfect for portable or automotive battery operated RF data loggers, beam steering, LIDAR/RADAR or waveform synthesis applications powered via a 6-14V DC supply [...] (+)

      Features:

      333882733491719056.jpg
    • XU-TX
      An XMC module with two, 5.1 GSPS, 16-bit DAC's, PLL, 8 GB DDR4 and Xilinx UltraScale FPGA. A Xilinx Kintex UltraScale XCVU060/085 FPGA lies at the heart of the product, supported by with 8 GB DDR4 and 4 MB of QDRAM memory, providing a very high performance DSP core for demanding applications such RADAR and wireless IF generation. (+)

      Features:

      • Two 16-bit, > 5.1 GSPS DAC channels: Single ended AC coupled outputs with programmable DC bias Differential DC model option >2 GHz analog bandwidth (1X) Digital inverse sinc filter Enhanced 2nd and 3rd Nyquist modes “Frequency doublingâ€? 2X mode Interpolation filters: 1X(bypassed)-64x 48 bit NCO and 31 32bit fast hop NCOs
      • Up to 7800 MB/s streaming via PCIe or Aurora Internal or external clocking Internal 0.3 to 4.8 GHz PLL each DAC Internal or external triggering Fixed latency, multi-board synchronization
      • Xilinx Kintex UltraScale FPGA XCKU060/085:
    • X6-1000M
      Integrates high-speed digitizing and signal generation with signal processing on a PMC/XMC IO module for demanding DSP applications. (+)

      Features:

      • Two 1 GSPS, 12-bit A/D channels
      • Two 1 GSPS, 16-bit DAC channels
      • +/- 1V, AC or DC -Coupled, 50 ohm, SMA inputs and outputs
    • X3-DIO
      64 single-end/32 differential digital I/O (+)

      Features:

      • 100 MHz signal rates to FPGA using LVDS
      • 50 MHz LVCMOS signal rates
      • 400 MB/s LVDS capture/playback to SRAM
    • XMC Modules Kintex UltraScale & Virtex Advantage
      Introducing cutting-edge I/O without the increased investment and risk required to include such new technology in larger, fully custom products. The XU-TX is an XMC module which features two AC-coupled single-ended 16-bit DAC outputs with programmable DC bias. The DAC devices employed support synchronization, interpolation, and their unique output circuits allow improved frequency synthesis in the 2nd Nyquist zone. This can shift the Nyquist null frequency in the output spectrum to two times the typical Nyquist null frequency. The maximum sample rate of the DAC IC is 12 GSPS, the maximum external direct clocking rate is 6 GSPS and the on board PLL can generate clocks up to 4.8 GHz. The DACs' JESD 204B interfaces can stream data with transfer rates up to 6 GSPS. The XA Family provides an extremely economical solution for real-time, FPGA-accelerated stimulus-response applications such as RADAR, LIDAR, optical servo or medical scanning. Mated with one of our rugged, embedded PCs, the XA-160M becomes an autonomous, self-booting instrument with dual, 10 GbE connectivity " perfect for distributed instrumentation. Applications: High Speed Arbitrary Wave Generation, Wireless MIMO transmitter, RADAR Waveforms, Electronic Warfare, Medical Scanning & Imaging, Optical servo, LIDAR, Servo Control, High speed stimulus-repsonse & (+)

      Features:

      • XU Series 4GB component memory system Eight x 16 2400 MHZ DDR4 SDRAM sync bandwidth of 20 GB/s! One x 18 600 MHz QDR SRAM bandwidth to 72 Mbit
      • XU-TX 12 GSPS - 2 channel 16-bit transmitter
      • XU-RX 4 GSPS - 2 channel 12-bit receiver
    • FMC-1000M
      FMC Module with 2x 1250 MSPS 14-bit A/D, 2x 1250 MSPS 16-bit DAC with PLL and Timing Controls, (+)

      Features:

      • Two 14-bit A/D Inputs 1250 MSPS AC or DC coupled
      • Two 16-bit D/A outputs 1250 MSPS @ 1x, 2500 MSPS @ 2x interpolation AC or DC coupled
      • Sample clocks and timing and controls External clock/reference input Programmable PLL 10 MHz, 0.5 ppm reference Integrated with FMC triggers
    • X6-250M PMC/XMC Module with 8 250PSPS
      The X6-250M integrates digitizing with signal processing on a PMC/XMC IO module. The module has a powerful Xilinx Virtex 6 FPGA signal processing core, and high performance PCI Express/PCI host interface. Applications include software-defined radio, RADAR receivers, and multi-channel data recorders. (+)

      Features:

      214503304641304979.jpg
      • Eight 250 MSPS, 14-bit A/D channels
      • +/-1V, AC-Coupled, 50 ohm, SSMC inputs
      • Xilinx Virtex6 SX315T/SX475T or LX240T
    • Quadia.. Advanced Signal Capture & Realtime
      1 GHz TMS320C6416 DSP (x4) (+)

      Features:

      22230.jpg
      • 64 MB SDRAM per processor
      • Flexible internal/external communication mesh
      • 64-bit/66 MHz CompactPCI
  • Interface Concept  (2)
    • IC-DC2-VMEb
      The IC-DC2-VMEb, being VME64x-VITA31.1 compliant, is aimed at highly integrated applications like leading-edge computing, embedded network control, signal processing, etc. The large number of interfaces turns this IC-DC2-VMEb into an ideal open platform for a wide range of applications. The board boasts an AMD/ATI M96 Graphic Processor Unit (Radeon E4690- R700 core), which provides the IC-DC2-VMEb with the performance needed for high demanding embedded graphics applications (marine and airplane displays, industrial monitoring, medical equipment, night vision systems...). The analog video interfaces offer STANAG B & C support, especially useful to airborne applications. While maintaining a low power-consumption and a wide temperature range, the IC-DC2-VMEb benefits from a long life product cycle for high reliability and safety critical embedded applications. (+)

      Features:

      188284515194296216.jpg
      • based on an Intel Core2 Duo processor SL9380 processor
      • VME64x-VITA31.1 compliant
      • AMD/ATI M96 Graphic Processor Unit
    • IC-FEP-TCAa
      New FPGA Xilinx Virtex®-7 processing engine in a single MTCA.4 form factor (+)

      Features:

      295068508410660521.jpg
      • FPGA Xilinx Virtex®-7
      • MTCA.4 form factor
      • Six Serdes transceivers
  • Kontron  (3)
    • VX6060
      HPEC computer blade in 6U VPX format (+)

      Features:

      44028.jpg
      • Two independently implemented Intel Core i7 processing nodes
      • VPX computing blade for parallel data and signal processing applications
      • Two independently implemented Intel Core i7 processing nodes linked to a powerful Ethernet and PCIe infrastructure
    • StarVX - High Performance Embedded Computing
      The Kontron StarVX HPEC Proof-of-Concept delivers breakthrough I/O data bandwidth in small footprint for next-generation embedded radar/sonar applications. Kontron designed the StarVX HPEC PoC to help developers dramatically streamline the process from design to field deployment of next-generation radar and sonar applications. Based only on mainstream IT technology (TCP/IP, PCIe, Intel® CPUs), the Kontron StarVX HPEC PoC is also developed to address the U.S. military’s smart procurement initiatives that put into place more rapid and agile purchasing processes. Co-developed with Intel, the Kontron StarVX HPEC PoC demonstrates the breakthrough technology that restores matched I/O and CPU performance ratios. Based on the 3rdgeneration Intel® Core™ processors and the Kontron 3U VPX platform, the Kontron StarVX HPEC PoC leverages Kontron’s extensive computing platform design capabilities in small, air cooled or conduction-cooled platforms. The Kontron StarVX HPEC PoC presents an optimal application-ready solution for radar and sonar systems that are expected to make a tremendous jump in a processing power and data I/O bandwidth. FEATURES: » Based on the latest Intel® Core™ i7 processors » Rugged, conduction-cooled 3U VPX-based system » 24 lanes of PCI Express® (PCIe®) centralized backplane interconnect at gen3 speed » Utilizes VXFabric™ software [...] (+)

      Features:

    • StarVX - High Performance Embedded Computing
      The Kontron StarVX HPEC Proof-of-Concept delivers breakthrough I/O data bandwidth in small footprint for next-generation embedded radar/sonar applications. Kontron designed the StarVX HPEC PoC to help developers dramatically streamline the process from design to field deployment of next-generation radar and sonar applications. Based only on mainstream IT technology (TCP/IP, PCIe, Intel® CPUs), the Kontron StarVX HPEC PoC is also developed to address the U.S. military’s smart procurement initiatives that put into place more rapid and agile purchasing processes. Co-developed with Intel, the Kontron StarVX HPEC PoC demonstrates the breakthrough technology that restores matched I/O and CPU performance ratios. Based on the 3rd generation Intel® Core processors and the Kontron 3U VPX platform, the Kontron StarVX HPEC PoC leverages Kontron’s extensive computing platform design capabilities in small, air cooled or conduction-cooled platforms. The Kontron StarVX HPEC PoC presents an optimal application-ready solution for radar and sonar systems that are expected to make a tremendous jump in a processing power and data I/O bandwidth. FEATURES: » Based on the latest Intel® Core i7 processors » Rugged, conduction-cooled 3U VPX-based system » 24 lanes of PCI Express® (PCIe®) centralized backplane interconnect at gen3 speed » Utilizes VXFabric software [...] (+)

      Features:

  • Mistral Solutions Pvt. Ltd.  (1)
    • OMAP3 EVM
      The OMAP3 EVM is an ideal software development and device prototyping platform for users to get started on their wireless/multimedia based application and device development (+)

      Features:

      • Built around TI's OMAP35x processor powerful 35x processor comprising of advanced Superscalar ARM Cortex-A8 RISC core with NEON co-processing, IVA2.2 subsystem with a C64x+ digital signal processor (DSP) core and SGX subsystem for 2D and 3D graphics acceleration
      • Support for multiple display outputs like VGA LCD, DVI, S-Video and Composite-Video
      • Modular & extendable architecture
  • Nallatech  (3)
    • XMC-240
      FPGA processing and analog input PMC/XMC mezzanine (+)

      Features:

      42876.jpg
      • Designed to meet the signal processing needs of modern signal intelligence, software defined radio and radar applications
      • The XMC-240 is the latest product to be introduced to the highly successful Nallatech REVX Series of rugged embedded processing solutions
      • The XMC-240 features four channels of analog input that can sample analog signals at up to 250 MSPS with 14 bits resolution
    • VXS-620 FPGA
      FPGA and PowerPC VXS multiprocessor (+)

      Features:

      42875.jpg
      • Designed to meet the signal processing needs of modern signal intelligence, software defined radio, and radar applications
      • The VXS-620 is the latest product to be introduced to the highly successful Nallatech REVX Series of rugged embedded processing solutions
      • The VXS-620 features an onboard Xilinx Virtex-5 FPGA for the implementation of high performance DSP applications
    • VXS-610
      Dual FPGA and PPC multiprocessor VXS card (+)

      Features:

      • Single-slot VXS card
      • PowerPC node with MPC8548E processor
      • Two FPGA nodes with Xilinx Virtex-5 LX155T or SX95T
  • National Semiconductor  (2)
    • LM49352 and LM49151
      The PowerWise LM49352 mixed-signal audio subsystem and LM49151 analog subsystem are targeted at smart phones, full-featured phones, portable gaming devices, and GPS devices (+)

      Features:

      41693.jpg
      • The LM49352 is a mixed-signal audio subsystem that integrates audio codec functionality with ground-referenced headphone amplifiers, earpiece driver, Class D loudspeaker and audio Digital Signal Processor (DSP) in one miniature 3.3 mm by 3.3 mm package
      • The loudspeaker delivers ultra-high efficiency (93 percent at 970 mW from a 4.2 V supply), while the headphone amplifier offers low-power (18 mW) MP3 playback to extend battery life
      • The LM49151 analog subsystem integrates an earpiece driver, Class D loudspeaker, ground-referenced headphone amplifiers and automatic level control (ALC) in an ultra-small 2.2 mm by 2.6 mm package
    • Sensor WEBENCH
      National Semiconductor's WEBENCH Sensor Designer tool enables engineers to quickly move from concept to simulation to prototyping of common sensor solutions (+)

      Features:

      • National's WEBENCH Sensor Designer tool matches the industry's leading bridge pressure sensors, photo detector sensors and thermocouple sensors with National's PowerWise energy-efficient op amps and pin- and function-compatible 8-, 10-, 12-, 14- and 16-bit ADCs
      • Each signal path solution amplifies, conditions and digitizes the sensor output to directly link to a microcontroller or digital signal processor (DSP)
      • Using the ‘Build It!' option, designers can generate solutions they can use for evaluation and prototyping
  • Neff Instrument Corporation  (1)
    • Dynamic Signal Acquisition
      Individual digital signal processors complete with transducer conditioning including programmable excitation, excitation readback, and auto-identification of channel configuration; programmable gain amplifier; built-in autocalibration; programmable filter cutoff frequency; rolloff rates greater than 290 dB per octave; ADC per channel; bandwidth to 14 KHz; channel sampling rates to 37 KHz; and aggregate throughput rate to 2 Msamples/sec (+)

      Features:

      • Digital filters guarantee phase matching [...]
  • Nuvoton Technology  (1)
    • WAU8812
      Mono audio Codec for VoIP-telephone, hands-free telephony markets; provides flexibility in performance and power consumption (+)

      Features:

      38376.jpg
      • Robust, high-fidelity, 24-bit signal architecture
      • 93dB Digital-to-Analog Converter (DAC), Signal to Noise Ratio (SNR), and 91dB Analog-to-Digital Converter (ADC) SNR at audio sampling rates from 8 KHz to 48 KHz
      • Industry-leading 6uA standby current, which greatly reduces power consumption and extends battery life in hand-held applications
  • Parsec  (3)
    • PM431
      A PMC module that employs FPGA technology to provide a high bandwidth processing platform targeted at typical Radar/Video functions such as FFT, FIR filters, and convolution (+)

      Features:

      41445.jpg
      • FPGAs: High speed DSP processing in ALTERA Stratix FPGA; EP1S25C6 Processing FPGA (standard) to EP1S40 ; onboard non-volatile storage of FPGA configuration data; Two banks of Processing FPGA configuration data provided; automatic configuration of FPGAs after power-up
      • Memory: standard: 5 x 256K x 36 ZBT memories (5 MB); Optional: 5 x 512K x 36 ZBT memories (10 MB)
      • PCI Interface:
    • COTS Radar Signal Processor Platform
      Programmable RSP platform (+)

      Features:

      • High processing bandwidth
      • High data bandwidth
      • Built-in test features
    • PM432
      A single PMC module that leverages on ALTERA Stratix II GX FPGA technology to provide a high-speed, high-bandwidth processing platform, ideally suited for Software Defined Radio (SDR), WiMAX, Radar, Video, as well as other computation and bandwidth intensive applications (+)

      Features:

      41446.jpg
      • Processing FPGA
      • EP2SGX90 ALTERA Stratix II GX FPGA
      • 90,960 Logic Elements, 192 18x18 multipliers and 4.3 Mb RAM
  • Pentek, Inc.  (15 of 33)
    • 71851
      Jade family of data converter XMC modules. The Model 71851 is based on the Xilinx Kintex Ultrascale FPGA and features two 500 MHz, 12-bit A/Ds with multiband digital down converters (DDCs), one digital upconverter (DUC) and two 800 MHz 16-bit D/As. The Model 71851 offers a well-matched 200 MHz bandwidth on both the receive-side and on the transmit-side, which provides the complimentary solution necessary in many high-speed data acquisition, waveform generation, communications, satcom, UAV and radar applications (+)

      Features:

      3697998766215604825.jpg
      • The front end accepts two analog HF or IF inputs on front panel SSMC connectors with transformer-coupling into two Texas Instruments ADS5463 500 MHz, 12-bit A/D converters
      • A TI DAC5688 DUC (digital upconverter) and D/A accepts a baseband real or complex data stream from the FPGA and provides that input to the upconvert, interpolate and dual D/A stages
      • A/D Acquisition IP Modules: The Model 71851 features two A/D Acquisition IP modules for easily capturing and moving data. Each module can receive data from any of the two A/Ds or a test signal generator
    • RTR 2727
      the Model RTR 2727 rugged portable recorder suitable for military and aerospace applications. The system features recording and playback of IF signals up to 700 MHz with signal bandwidths to 200 MHz. It can be configured with 500 MHz 12-bit A/Ds or 400 MHz 14-bit A/Ds and an 800 MHz 16-bit D/A. Pentek’s SystemFlow software allows turnkey operation through a graphical user interface (GUI), while the SystemFlow application programming interface (API) allows easy integration of the recording software into custom applications. (+)

      Features:

      223484716525535130.jpg
      • Designed to operate under conditions of shock and vibration
      • Portable system measuring 16.9" W x 9.5" D x 13.4" H
      • Lightweight: approximately 30 pounds
    • Cobalt 78621
      A data acquisition module for high-performance applications and part of Pentek Inc.'s Cobalt family (+)

      Features:

      • Utilizes Xilinx's Virtex®-6 FPGA family for onboard signal processing
      • Available in both XMC and PCIe formats to satisfy a range of system needs
      • Includes ruggedized XMC-format modules with extended temperature range options for deployed applications such as an unmanned aerial vehicle (UAV) collecting radar and signal intelligence data
    • Model RTR 2726
      The Talon® RTR 2726 is a turnkey, multiband recording and playback system that allows the user to record and reproduce high-bandwidth signals with a lightweight, portable and rugged package. The RTR 2726 provides aggregate recording rates of up to 2.4 GB/sec and is ideal for the user who requires both portability and solid performance in a compact recording system. (+)

      Features:

      311483491927561.jpg
      • Designed to operate under conditions of shock and vibration
      • Portable system measuring 16.9" W x 9.5" D x 13.4" H
      • Lightweight: approximately 30 pounds
    • SigPro 1
      Small Form Factor (SFF) acquisition system that combines OpenVPX devices from Elma Electronic, Pentek, and Concurrent Technologies (+)

      Features:

      • The multivendor platform is targeted at radar, signal processing, high-speed data acquisition, and beamforming applications
      • SigPro 1 is based on the Pentek Cobalt FPGA XMC products with a high-performance analog-to-digital front end and the 803 Series 3U VPX-REDI Corei7 Single Board Computer (SBC) from Concurrent Technologies for processing functions and a storage subsystem that is based on solid-state disk from Elma
      • The new solution uses a three-slot VPX backplane in a conduction-cooled chassis and uses sealed MIL-STD DTL 38999 connectors for I/O
    • 6235-401
      GateFlow dual wideband 1k FFT receiver VIM-2 module (+)

      Features:

      32551.jpg
      • Dual 12-bit 105 MHz A/Ds
      • Built-in real-time 105 MHz 1k or 4k FFT processor
      • Radar preprocessor
    • Cobalt Model 71664
      The Model 71664 comes preconfigured with a suite of built-in functions for digital down conversion, data capture, synchronization, time tagging, and formatting, making them ideal turn-key interfaces for radar, communications or general data acquisition applications. IP modules for A/D acquisition, DDC, DDR3 or QDRII+ memories, programmable beamforming, controller for data clocking and synchronization, and a VRT protocol engine are all included. (+)

      Features:

      335617248561987861.jpg
      • Complete radar and software radio interface solution
      • PCIe output supports VITA 49.0 VITA Radio Transport (VRT) Standard
      • Supports Xilinx Virtex-6 LXT and SXT FPGAs
    • Cobalt 71621
      Three 16-bit, 200 MHz A/Ds, three multiband DDCs (digital downconverters), two 16-bit 800 MHz D/As with DUC (digital upconverter) and interpolator (+)

      Features:

      • Complete radar and software radio interface solution
      • Supports Xilinx Virtex-6 LXT and SXT FPGAs
      • Three 200 MHz 16-bit A/Ds
    • Model 71624
      The Model 71624 dual channel, 34 signal, adaptive IF (Intermediate Frequency) relay XMC with a Virtex-6 FPGA. As an IF relay, it accepts two IF analog input channels, modifies up to 34 signals, and then delivers them to two analog IF outputs. Any signal within each IF band can be independently enabled or disabled, and changed in both frequency and amplitude as it passes through the module. The Model 71624 supports many useful functions including signal drop/add/replace, frequency shifting and hopping, amplitude equalization, and bandwidth consolidation. (+)

      Features:

      308688793538844775.jpg
      • Modifies 34 IF signals between input and output
      • Up to 80 MHz IF bandwidth
      • Two 200 MHz 16-bit A/Ds
    • 71760 Onyx
      The next generation of the company’s Virtex-6 Cobalt line -- a four-channel, 200 MHz A/D XMC module targeted at SDR and signal-processing applications in military radar, communication, and Unmanned Aircraft System (UAS) programs (+)

      Features:

      • The new Onyx devices have the same modular I/O interfaces as their Virtex-6 FPGA Cobalt line of products, while increasing memory, I/O performance, and logic
      • The 71760, for instance, is similar to the Pentek Cobalt 71660, but has twice the memory capacity and I/O bandwidth
      • Enhancements in the Onyx product line include doubling the DDR3 memory in size and speed to 4 GB and 1,600 MHz, respectively
    • RTS 2701
      Rack-mount Real-Time Data Recording and Playback System with Multiband Transceiver (+)

      Features:

      43193.jpg
      • Complete dual-channel recording and playback system
      • 19-inch industrial rack-mount PC server chassis
      • High-performance Windows workstation
    • Onyx Model 71720
      Model 71720 3-Channel 200 MHz A/D and 2-Channel 800 MHz D/A with Virtex-7 FPGA - XMC (+)

      Features:

      223485199525664546.jpg
      • Supports GateXpress FPGA-PCIe Configuration Manager
      • Complete radar and software radio interface solution
      • Supports Xilinx Virtex-7 VXT FPGAs
    • Onyx Model 71730
      Model 71730 is a member of the Onyx® family of high performance XMC modules based on the Xilinx Virtex-7 FPGA. A highspeed data converter, it is suitable for connection to HF or IF ports of a communications or radar system. (+)

      Features:

      248454973525477800.jpg
      • Complete radar and software radio interface solution
      • Supports Xilinx Virtex-7 VXT FPGAs
      • GateXpress supports dynamic FPGA reconfiguration across PCIe
    • Model 56721
      Model 56721 is a member of the Onyx® family of high performance AMC boards based on the Xilinx Virtex-7 FPGA. A muti-channel, high-speed data converter with a programmable DDC, it is suitable for connection to HF or IF ports of a communications or radar system. Its built-in data capture and playback features offer an ideal turnkey solution. (+)

      Features:

      292411886442203400.jpg
      • Complete radar and software radio interface solution
      • Supports Xilinx Virtex-7 VXT FPGAs
      • GateXpress supports dynamic FPGA reconfiguration across PCIe
    • Model 7142-428 Digital Transceiver
      Digital Transceiver with Multiband DDC Core and Interpolation Filter (+)

      Features:

      • Ideally suited for military software defined radio systems that require flexible hardware capable of emulating multiple radio waveforms
      • A complete software radio system in a COTS PMC/XMC module
      • Quad DDC IP Core Combines Narrowband and Wideband Functions
  • Pentland Systems  (1)
    • RAD2
      Digital receiver featuring dual channel, 14-bit resolution with up to 105MSPS sampling speed (+)

      Features:

      16182.jpg
      • Up to 16 individual down-converter channels for I&Q demodulation
      • Xilinx Virtex II FPGA for digital signal processing and A/D control
      • Bi-directional high-speed FIFO buffers
  • Pickering Interfaces Ltd.  (1)
    • 41-100-001
      Frequency Counter (+)

      Features:

      • Peak Power Meter
      • Time Interval Analyzer of Pulsed RF Input
      • Continuous or Pulsed RF Input Signal
  • RF Engines Limited  (2)
    • DSP Cores for FPGA
      Signal processing cores are highly optimized FPGA designs for applications with high sample rates and demanding performance requirements (+)

      Features:

      • Guaranteed bit-true models provided with each core
      • Highly optimized implementations using pipelined architectures
      • Designs tailored to specific bit width and precision requirements
    • SpectraView™ SV900
      RF Engines' SpectraView™ SV900 system is being developed to provide a complete and cost-effective solution for performing real-time spectral analysis of very wideband analog signals. The SV900 is based around the latest high performance digitisers and powerful signal processing hardware, and can be interfaced directly to a standard personal computer. The package includes Advanced Signal Display Software (ASDS), a full-featured PC application that provides the user interface to the analysis system, with a variety of mechanisms for displaying, analysing and storing both time and frequency domain data. (+)

      Features:

      • Cost-effective spectral analysis solution
      • Extremely wideband analysis capabilities
      • Minimal setup and configuration
  • Sensoray Co., Inc.  (2)
    • Model 2253P | USB H.264 A/V Codec with GPS and Incremental Encoder Interfaces
      Model 2253P is a compact and robust USB-compatible audio/video codec that is powered from a single USB port. The unit is capable of simultaneously producing two different video streams from its single composite input and sending the streams out over USB. Video and audio are available as elementary streams or may be multiplexed in MP4 container format. The Model 2253P can also perform as a decoder, converting the compressed audio/video stream into standard analog video and audio signals, as well as offering closed-caption support for H.264 streams. It is well-suited for uncompromising capture of various video sources, such as video pipeline inspection, radar and sonar processing, remote video surveillance and traffic monitoring. The Model 2253P features a GPS receiver and two incremental encoder interfaces accessible through two RJ-45 sockets. Each multifunction interface can be independently configured to operate as an incremental encoder interface or as two digital inputs. When a port is configured as dual digital inputs, each of the inputs can optionally be used to pause/resume capture of a video stream. FEATURES: - Simultaneous encode/decode/preview in a robust, compact unit - Low preview latency - H.264 HP@L3, MPEG-4 ASP, MJPEG video compression - AAC, G.711 audio compression, uncompressed PCM - Unicode text and graphic overlay - Closed caption/VBI support for H.264 streams - GPS receiver and two incremental encoder interfaces/dual GPIO - Incremental encoder counts and GPS data can be overlaid onto video - Ideal for video pipeline inspection, radar processing and video surveillance applications [...] (+)

      Features:

    • Model 2253P | USB H.264 A/V Codec with GPS and Incremental Encoder Interfaces
      Model 2253P is a compact and robust USB-compatible audio/video codec that is powered from a single USB port. The unit is capable of simultaneously producing two different video streams from its single composite input and sending the streams out over USB. Video and audio are available as elementary streams or may be multiplexed in MP4 container format. The Model 2253P can also perform as a decoder, converting the compressed audio/video stream into standard analog video and audio signals, as well as offering closed-caption support for H.264 streams. It is well-suited for uncompromising capture of various video sources, such as video pipeline inspection, radar and sonar processing, remote video surveillance and traffic monitoring. The Model 2253P features a GPS receiver and two incremental encoder interfaces accessible through two RJ-45 sockets. Each multifunction interface can be independently configured to operate as an incremental encoder interface or as two digital inputs. When a port is configured as dual digital inputs, each of the inputs can optionally be used to pause/resume capture of a video stream. FEATURES: - Simultaneous encode/decode/preview in a robust, compact unit - Low preview latency - H.264 HP@L3, MPEG-4 ASP, MJPEG video compression - AAC, G.711 audio compression, uncompressed PCM - Unicode text and graphic overlay - Closed caption/VBI support for H.264 streams - GPS receiver and two incremental encoder interfaces/dual GPIO - Incremental encoder counts and GPS data can be overlaid onto video - Ideal for video pipeline inspection, radar processing and video surveillance applications [...] (+)

      Features:

  • SKY Computers, Inc.  (1)
    • 2U Rack Mount
      2U Rack Mount Digital Signal Processor (+)

      Features:

      • Intel based Digital Signal Processing Computing System
      • Designed for radar or imaging applications
      • Input bandwidth: 2.5 GByte per second
  • Spectrum Digital  (3)
    • eZdsp for TMS320VC5410
      A starter kit for the TMS320VC5410 DSP (+)

      Features:

      • TMS320VC5410 Digital Signal Processor operating at 100 MHz
      • Embedded IEEE 1149.1 JTAG scan controller
      • Interface to host PC through parallel port for debug and communications
    • eZdsp for TMS320VC33
      A starter kit for the TMS320VC33 DSP (+)

      Features:

      • TMS320VC33 Digital Signal Processor operating at 60 MHz
      • Embedded IEEE 1149.1 JTAG scan controller
      • Interface to host PC through parallel port for debug and communications
    • eZdsp for TMS320VC5402
      A starter kit for the TMS320VC5402 DSP (+)

      Features:

      • TMS320VC5402 Digital Signal Processor operating at 100 MHz from Texas Instruments
      • Embedded IEEE 1149.1 JTAG scan controller
      • Interface to host PC through parallel port for debug and communications
  • Spectrum Signal Processing  (11)
    • Ingliston
      A quad PCI DSP system based on the 250 MHz, fixed-point 'C6202 processor (+)

      Features:

      3663.jpg
      • 2000 MIPS
      • One PMC mezzanine site
      • Two PEM Mezzanine sites
    • Barcelona/67
      CompactPCI DSP system supports TMS320C6701 architecture (+)

      Features:

      • Dual or quad processor with distributed shared memory architecture provided by the Hurricane PCI-to-DSP bridge chip
      • SBSRAM distributed shared memory
      • Additional I/O capabilities include IP Modules, PMC modules, DSP-Link 3, custom I/O, and Spectrum-developed PEM modules which provide 400 Mbytes/sec of I/O bandwidth per DSP
    • TIM-SDR
      Single-channel digital radio receiver module with software demodulation libraries (+)

      Features:

      • This surveillance solution combines an A/D converter, digital down converter, TMS320C44 DSP processor, and a D/A converter on a single-wide TIM-40 module
      • Designed to work with Spectrum's LeMans VXI product [...]
    • TIM-SDR
      Single-channel digital radio receiver module with software demodulation libraries (+)

      Features:

      • This surveillance solution combines an A/D converter, digital down converter, TMS320C44 DSP processor, and a D/A converter on a single-wide TIM-40 module
      • Designed to work with Spectrum's LeMans VXI product [...]
    • Smart Antenna Development Platform
      A Smart Antenna Development Platform that leverages upon the reconfigurability, flexibility, and modularity of Spectrum's flexComm solutions (+)

      Features:

      • Targeted at government and commercial users that require increased capacity, extended range, and signal enhancement to get the most out of their infrastructure investment.
      • Supports two to eight receive channels with a 10 MHz bandwidth and can scan the frequency range from 20 MHz to 3 GHz, sufficient for all military communications and cellular bands
      • Provides a direction finding example program that can determine the relative position of an incoming narrowband signal
    • flexComm SDR-4000 TMRDP
      Off-the-shelf platform to develop and deploy their complex tactical MILCOM applications (+)

      Features:

      • Tactical Military Communications (MILCOM) Rapid Deployment Platform (TMRDP)
      • Platform equips quick response teams with an integrated platform designed for the rapid development and deployment of tactical MILCOM applications
      • The commercial-off-the-shelf SDR-4000 TMRDP provides full "RF to Ethernet" functionality of a software defined radio (SDR) with support for the Software Communications Architecture (SCA) in a single 19" rack
    • flexComm SDR-4000 WML
      Wireless Modem Lite (WML) (+)

      Features:

      • A lower power rugged package that supports the critical modem, link, and network layer processing functions necessary in a software defined radio
      • The Lite version reduces the power required per slot by supporting a selective feature set from Spectrum's SDR-4000 products
      • Specifically designed for tactical Military Communications (MILCOM) applications and provides black-side "IF to Ethernet" digitization and processing of complex waveforms
    • PMC-2MAI Dual A/D Converter PMC Module
      Two 12-bit 65 MSPS A/D converters (+)

      Features:

      • Digital step attenuator allowing input levels from -9 to +6 dBm
      • Digital signal level monitor
      • External input/output clock source
    • Barcelona-HS
      A 6U, hot-swap CompactPCI board combining DSP multiprocessor hardware and software tools for designing high availability systems (+)

      Features:

      11843.jpg
      • Fixed-point or floating-point DSP signal processing engine
      • Ultra-high bandwidth mezzanine interfaces directly to DSP
      • Compliant with PICMG 2.1 R2.0
    • LeMans - Octal TMS320C4x VXIbus Master Board
      The LeMans 840 MFLOP octal TMS320C4x VXIbus master board can host up to six single-wide or four double-wide 'C40/44 DSP modules and TIM-40 form factor SRAM, DRAM, EDRAM, or I/O modules (+)

      Features:

      • Supports VXI shared memory, VXI master/slave modes, and 80 Mbytes/sec data transfers via the HP local bus
      • Features JTAG input and output connectors, a test bus controller, and device driver support via VISA or SICL [...]
    • TMI-3350 4-Channel Wideband Analog I/O
      Hot swappable (+)

      Features:

      22244.jpg
      • External frequency reference input for accurate sampling frequency control and time-stamping
      • IRIG-B time code input for time stamping
      • Synchronization connector allows up to three TM1-3350 and DDCs/DUCs running on PRO-3100 boards to receive a common synchronization signal
  • Synopsys, Inc.  (1)
    • SPW Hardware Design System (HDS)
      Fastest path from innovation into implementation for digital signal processing systems, applying a model-based design approach (+)

      Features:

      46490.jpg
      • At its core is the C Data Flow (CDF) modeling paradigm, which enables the most efficient description of digital signal processing systems which may be implemented in dedicated digital hardware or embedded software
      • SPW Hardware Design System (HDS) is a key component in the SPW product family
      • It accelerates the hardware design, verification, and analysis of complex, algorithm intensive Digital Signal Processing (DSP) systems
  • The MathWorks, Inc.  (1)
    • Signal Processing Toolbox
      A collection of MATLAB functions that provides a rich, customizable framework for analog and digital signal processing (+)

      Features:

      • Tools for finite impulse response (FIR) and infinite impulse response (IIR) digital filter design, analysis, and implementation
      • Extensive list of filter structures
      • Widely-used transforms, including fast Fourier transform (FFT) and discrete cosine transform (DCT)
  • Traquair Data Systems, Inc.  (1)
    • ORS-11x
      Multi-channel analog interfaces with a user-programmable Spartan-IIE or Virtex-II FPGA, providing developers with the means to implement FPGA-based digital signal processing solutions (+)

      Features:

      31753.jpg
      • Can be used as stand-alone devices with the user-programmable FPGA responsible for supporting all signal processing functionality, or as daughtercards to micro-line DSP/FPGA boards
      • A variety of multi-channel A/D/A configurations are supported: 2-channel 14-bit A/D/A with ADC sample rates up to 65 MSps; 4-channel 16-bit A/D/A with ADC sample rates up to 2.5 MSps; 12-channel A/D/A with ADC sample rates up to 250 KSps
      • If the capabilities of a Texas Instruments TMS320C6000 DSP processor are required, an ORS-11x board can be fitted as a daughtercard to a TMS320C6000-based micro-line embedded DSP/FPGA board
  • XILINX, Inc.  (2)
    • Virtex-5 SXT platform
      Getting all the processing performance, memory and high-speed I/O is a never ending quest for applications heavy in digital signal processing (+)

      Features:

      32897.jpg
      • Integrating the flexibility of programmable logic makes building a processor even more challenging
      • The Xilinx Virtex-5 SXT platform establishes an industry record for DSP performance delivering 352 GMACs at 550MHz, while consuming 35 percent less dynamic power as compared to previous 90nm generation devices, and is the first DSP-optimized FPGA family to integrate serial transceivers
      • The Virtex-5 SXT platform delivers the highest ratio of DSP blocks-to-logic needed for high-performance digital signal processing applications in wireless, such as WIMAX and high-definition video, such as surveillance and broadcast
    • System Design Tools
      Build highly integrated 8- to 32-bit µP/µC systems (+)

      Features:

      19224.jpg
      • Implement sophisticated signal processing designs
      • Accelerate your real-time DSP processor systems [...]
  • ZTEC Instruments, Inc.  (8)
    • ZT100PC
      A DSP processor that provides high-speed signal acquisition and processing in a PC/104 instrument (+)

      Features:

      • 80 MHz TMS320C5X DSP
      • User interface is provided through the PC/104 bus or through the RS-232/485 serial port
      • 32 general purpose digital I/O ports
    • ZT500PXI
      14-Bit Arbitrary Waveform Generator (+)

      Features:

      • 2 mVpp to 7 Vpp Programmable Output Signal Range in 2 mV Steps
      • 300 MSample/s to 40 MSample/s Programmable Sample Rate
      • 200 MHz Maximum Analog Bandwidth
    • ZT420PXI-TMT
      PXI/CompactPCI 200MSPS Digitizer / Digital Oscilloscope (+)

      Features:

      • Ability to test both pre-defined and user defined telecom masks
      • Automated scope configuration file save and detailed examples on mask definition allow straightforward creation of specialized masks
      • Onboard DSP software allows capture of up to 1024 waveforms with microsecond duration rearm times between waveforms
    • ZT200VME
      A modular intermediate frequency (IF) processor providing IF signal detection, processing, and modulation in a 6U VMEbus instrument (+)

      Features:

      • TMS320C50 DSP provides a complete set of IF measurement and processing capabilities including magnitude/phase measurements, In-phase/Quadrature (IQ) measurements, modulation analysis, signal modulation and demodulation, error detection and correction, equalization and filtering, feedback control, and adaptive beam-forming and noise cancellation
      • Three IF inputs (100- kHz to 10 MHz adjustable frequency range)
      • 80 dB input signal dynamic range
    • ZT400VXI
      A high-speed digitizer (+)

      Features:

      • DC to 150 MHz analog input bandwidth
      • ± 1V analog input signal range
      • X1, X2, X4, and X5 selectable analog input gain
    • ZT400VXI
      A high-speed digitizer (+)

      Features:

      9289.jpg
      • DC to 150 MHz analog input bandwidth
      • ± 1V analog input signal range
      • X1, X2, X4, and X5 selectable analog input gain
    • ZTC400SCU
      Analog input: DC to 150 MHz bandwidth (+)

      Features:

      • Analog signal range: 1V maximum
      • 500 MSamples/sec sample rate
      • 12-bit ADC resolution
    • ZT450PXI-00 -Digital-Storage Oscilloscope
      2 (PCI, PXI) or 4 (VXI) channels (+)

      Features:

      • 8-bit resolution
      • 1 GSps to 2.5 GSps single-channel interleaved sample rates
      • 500 MHz to 1 GHz max analog bandwidth
06/27/22 06:00
Close

Subscribe to DSP updates